工业设备批发在 Qoovee市场

Liquid fuel and gas boilers KVa are smooth-tube, the movement of the coolant takes place in a welded pipe system consisting of collectors and pipes of furnace and convective panels welded into them. Fuel entering through the burner device burns in the boiler combustion chamber, hot gases wash the tube surface of the combustion chamber, then enter the convective packets and through the flue duct are thrown into the chimney. The KVa boiler unit is installed on a frame with supports and has a frame with heat-insulating materials, sheathed with steel sheet. An explosion valve is installed in the rear screen of the furnace, which protects the boiler structure from destruction in the event of excessive pressure in the furnace. The burner is mounted in the front part of the combustion chamber. The front plate is fixed to the boiler with hinges and acts as a hatch, which allows access to the boiler combustion chamber for inspection and repair work without disassembling the front lining and insulation. The operation of the KVa hot water boiler is carried out with various models of burners that supply fuel to the combustion chamber, where it is burned and the coolant is heated. The block burner burns fuel, changes the combustion mode, maintains the water temperature in the boiler circuit up to 115 ° C. The temperature range of the water in the boiler circuit is set on the control panel. When the extreme values ​​are reached, the burner is switched on and off automatically. This mode ensures reliable and economical operation of the boiler. Technical characteristics of 0.4 MW KVA boilers Indicator name KVa 0.4 boiler Power of a hot water boiler, MW (Gcal / h) 0.4 (0.34) Fuel < / td> Gas Fuel oil Diesel Net calorific value, kcal / h 8120 9260 10200 Boiler efficiency, not less,% 91 85 91 Fuel consumption, nm3 / h (kg / h) 46 4337 Flue gas temperature, no more, ° С 200 220 220 Range of working regulation,% 40-100 Water consumption, m3 / h 14 Working water pressure, MPa (kgf / cm) 2 0.3-0.6 (3-6) Hydraulic resistance of the boiler, no more, MPa (kgf / cm) 2 0.07 (0.7) Water temperature, ° С 70-95 (90-115) Combustion chamber depth, mm 1710 Equivalent diameter, mm 700 Length, mm 2500 Width, mm 1200 Height, mm 1900 < / table>

Construction and arrangement: the presence of 2 loading doors; a large volume of the combustion chamber, for a one-time loading of a large volume of low-calorie wood fuel; the presence of a rotary chamber at the outlet of the boiler combustion chamber in front of the convective beam, which increases the afterburning zone of light and small fuel particles captured by the flow of exhaust gases. In wood-fired boilers with a capacity of 1.1 Gcal, high efficiency is achieved, by applying the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 200-180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of the fuel. The hydraulic circuit in the wood-fired boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler manifolds direct the coolant flow, eliminating the occurrence of stagnant zones and local overheating of heating surfaces. High velocities and turbulization of the water flow minimize the formation of scale, hot water boilers operate reliably without special water treatment. The water heating solid fuel boiler on wood 1,1 is made of a smooth-tube, horizontal layout, consists of two blocks: furnace and convective ... A cast-iron grate is installed in the firebox, at the front there are two cast-iron loading doors. The firebox of hot water boilers is shielded with gas-tight panels. The convective block consists of convective sections. Convective pipes are welded into the risers. The horizontal pipes of the convection sections in the convection block are staggered. The boilers have two convection blocks, separated by a gas-tight partition that guides the movement of gases. The convective heating surface of a hot water boiler consists of packages that can be easily dismantled during repairs even in a confined space (when the width of the passages between the boilers is one meter). In the lower part of the convective packages there is an ash bin with a manhole for cleaning from ash and soot and inspecting the pipes of the convective bundle. Hot water boilers have thermal insulation and a removable decorative casing. The lining of the boilers is made of mineral mats and refractory wire, the cladding is made of galvanized or sheet steel. Hot water boilers KV-1,1 are easy to maintain and repair due to the presence of hatches for inspection and cleaning of convective packages. To ensure safe operating conditions and design operating modes, the wood-fired hot water boiler 1,1 is equipped with safety and shut-off and control valves, instrumentation and safety devices. Shut-off valves are used to drain water from the boiler into the heating network, supply return water to the boiler, drain water from the boiler, for periodic blowdown and removal of sludge. Instrumentation, thermometers and pressure gauges ensure the measurement of pressure and temperature at the inlet and outlet of water from hot water boilers. Technical characteristics of the boiler 1,1 Gcal for wood fuel Name Wood-fired hot water boiler KVr-1,1 KD Power of a hot water boiler, MW (Gcal / h) 1.28 (1.1) Heated area with a ceiling height of 3 m2, m 11000 Working medium consumption, m³ / h 44 Working water pressure, MPa (kgf / cm²) 0.6 (6) Water temperature, ° C 70-95 Heating surface, m² 41 Hydraulic resistance, MPa (kgf / cm²) Not more than 0.02 (0.2) Fuel ( design) Firewood Qir = 2000 kcal / kg Boiler efficiency on design fuel,% Not less than 75 Flue gas temperature, ° C Not more than 210 Aerodynamic resistance, Pa (mm. water. st.) 80 Overall dimensions of the boiler, no more < td> Length, mm 3330 Width, mm 9050 < td> Height, mm 2200 Total weight of the boiler of a wood-fired hot water boiler, kg 3800

Construction and arrangement: the presence of 2 loading doors; a large volume of the combustion chamber, for a one-time loading of a large volume of low-calorie wood fuel; the presence of a rotary chamber at the outlet of the boiler combustion chamber in front of the convective beam, which increases the afterburning zone of light and small fuel particles captured by the flow of exhaust gases. In wood-fired boilers with a capacity of 0.6 Gcal, high efficiency is achieved, by applying the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 200-180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of the fuel. The hydraulic circuit in the wood-fired boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler manifolds direct the coolant flow, eliminating the occurrence of stagnant zones and local overheating of heating surfaces. High speeds and turbulization of the water flow minimize the formation of scale, hot water boilers work reliably without special water treatment. The 0.6 solid fuel boiler is made of a smooth-tube, horizontal layout, consists of two blocks: furnace and convective ... A cast-iron grate is installed in the firebox, at the front there are two cast-iron loading doors. The firebox of hot water boilers is shielded with gas-tight panels. The convective block consists of convective sections. Convective pipes are welded into the risers. The horizontal pipes of the convection sections in the convection block are staggered. The boilers have two convection blocks, separated by a gas-tight partition that guides the movement of gases. The convective heating surface of a hot water boiler consists of packages that can be easily dismantled during repairs even in a confined space (when the width of the passages between the boilers is one meter). In the lower part of the convective packages there is an ash bin with a manhole for cleaning from ash and soot and inspecting the pipes of the convective bundle. Hot water boilers have thermal insulation and a removable decorative casing. The lining of the boilers is made of mineral mats and refractory wire, the cladding is made of galvanized or sheet steel. Hot water boilers KV-0.6 are easy to maintain and repair due to the presence of hatches for inspection and cleaning of convective packages. To ensure safe operating conditions and design operating modes, a wood-fired hot water boiler 0.6 is equipped with safety and shut-off and control valves, instrumentation and safety devices. Shut-off valves are used to drain water from the boiler into the heating network, supply return water to the boiler, drain water from the boiler, for periodic blowdown and removal of sludge. Control and measuring devices, thermometers and manometers provide measurement of pressure and temperature at the inlet and outlet of water from hot water boilers. Technical characteristics of the boiler 0.6 Gcal for wood fuel Name Wood-fired hot water boiler KVr-0.6KD < / tr> Power of a hot water boiler, MW (Gcal / h) 0.6 (0.7) < tr> Heated area with a ceiling height of 3 m2, m 6000 Working medium flow rate, m3 / h 24 Working water pressure, MPa (kgf / cm²) 0.6 (6) < td> Water temperature, ° C 70-95 Heating surface, m2 27 Hydraulic resistance, MPa (kgf / cm²) Not more than 0.02 (0.2) Fuel (design ) Firewood Qir = 2000 kcal / kg Boiler efficiency on project fuel,% Not less than 75 < td> Flue gas temperature, ° C Not more than 210 Aerodynamic resistance, Pa (mm. water. st.) 67 Overall dimensions of the boiler, no more < td> Length, mm 2290 Width, mm 7050 < td> Height, mm 2100 Total weight of the boiler of a wood-fired hot water boiler, kg 2800

Construction and arrangement the presence of 2 loading doors; a large volume of the combustion chamber, for a one-time loading of a large volume of low-calorie wood fuel; < / li> the presence of a rotary chamber at the outlet of the boiler combustion chamber in front of the convective beam, increasing the afterburning zone of light and fine fuel particles captured by the flow of exhaust gases. In wood-fired boilers with a power of 0, 3 Gcal, high efficiency is achieved due to the application of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 200-180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of the fuel. The hydraulic circuit in the wood-fired boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler manifolds direct the coolant flow, eliminating the occurrence of stagnant zones and local overheating of heating surfaces. High velocities and turbulization of the water flow minimize the formation of scale, hot water boilers work reliably without special water treatment. The hot water solid fuel boiler on wood 0.3 is made of a smooth-tube, horizontal layout, consists of two blocks: a furnace and a convective ... A cast-iron grate is installed in the firebox, at the front there are two cast-iron loading doors. The firebox of hot water boilers is shielded with gas-tight panels. The convective block consists of convective sections. Convective pipes are welded into the risers. The horizontal pipes of the convection sections in the convection block are staggered. The wood-fired boiler 0.3 has two convection blocks, separated by a gas-tight partition that guides the movement of gases. The convective heating surface of a hot water boiler consists of packages that can be easily dismantled during repairs even in a confined space (when the width of the passages between the boilers is one meter). In the lower part of the convective packages there is an ash bin with a manhole for cleaning from ash and soot and inspecting the pipes of the convective bundle. Hot water boilers have thermal insulation and a removable decorative casing. The lining of the boilers is made of mineral mats and refractory wire, the cladding is made of galvanized or sheet steel. The KV-0.3 hot water boilers are easy to maintain and repair due to the presence of hatches for inspection and cleaning of convective packages. To ensure safe operating conditions and design operating modes, the boiler is equipped with safety and shut-off and control valves, instrumentation and safety devices. Shut-off valves are used to drain water from the boiler into the heating network, supply return water to the boiler, drain water from the boiler, for periodic blowdown and removal of sludge. Control and measuring devices, thermometers and manometers provide measurement of pressure and temperature at the inlet and outlet of water from water heating boilers. Technical characteristics of the boiler 0.3 Gcal for wood fuel Name Wood-fired hot water boiler KVr-0.3KD < / tr> Power of a hot water boiler, MW (Gcal / h) 0.35 (0.3) < tr> Heated area with a ceiling height of 3 m2, m 3000 Working medium consumption, m³ / h 12 Working water pressure, MPa (kgf / cm²) 0.6 (6) < td> Water temperature, ° C 70-95 Heating surface, m² 17 Hydraulic resistance, MPa (kgf / cm²) Not more than 0.02 (0.3) Fuel (design ) Firewood Qir = 2000 kcal / kg Boiler efficiency on project fuel,% Not less than 75 Flue gas temperature, ° C Not more than 200 Aerodynamic resistance, Pa (mm. water. st.) 51 Overall dimensions of the boiler, no more < td> Length, mm 1940 Width, mm 1300 < td> Height, mm 2050 Total weight of the boiler of a wood-fired hot water boiler, kg 1500

Boiler KVm 1.6 with TSPM The design of the boiler KVm 1.6 with TSPM (KVm 1.86) includes: high efficiency fuel combustion efficiency economic efficiency compactness reliability ease of use increased maintainability ease of installation lack of scale The KVm 1.6 hot water boiler with TShPM-2.0 is characterized by high efficiency, which is achieved through the use of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 180-200 ° C. The use of modern technology of fuel combustion in a bed reduces losses with mechanical and chemical underburning of fuel. The hydraulic circuit in the boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler collectors direct the flow of the coolant, eliminating the occurrence of stagnant zones and local overheating of heating surfaces, high speeds and turbulization of the water flow minimize the formation of scale, KVm 1.6 boilers operate reliably without special measures for chemical water treatment. Technical characteristics of a hot water boiler KVm 1.6 Gcal with TShPM-2.0 Power of a hot water boiler, Gcal / h (MW) 1.6 (1.86) Heated area with a ceiling height of 3 m, m² 12500 Fuel, coal Kuznetskiy D Kharanorskiy B1 Net calorific value 5230 2720 Boiler efficiency, not less,% 83 77 Fuel consumption, kg / h 370 764 Equivalent fuel consumption, kg / h 276 Outgoing temperature their gases, ° C Not more than 550 Working medium consumption, m³ / h 64 Water temperature, ° C 70-95 < td> Working medium pressure, MPa (kgf / cm²) 3-6 Boiler hydraulic resistance at a temperature difference of 25 ° C , MPa (kgf / cm²), no more than 0.07 (0.7) Aerodynamic resistance, Pa (mm water column), Combustion mirror area, m2 no more than 550 Combustion device KVr RPK furnace Gabaoite dimensions of the boiler block, no more < tr> Length, mm 4500 Width, mm 1950 Height, mm 3100

Boiler KVm 1.25 ZP RPK The design of the boiler KVm 1.25 with ZP RPK (KVm 1.44) includes: < li> high efficiency fuel combustion efficiency economy compactness reliability ease of use increased maintainability ease of installation no scale The KVm 1.25 ZP RPK hot water boiler is characterized by high efficiency, which is achieved due to application of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface provides a decrease in the temperature of flue gases from the boiler to 200 -180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of fuel. The hydraulic circuit in the boiler works in a counter-flow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler headers direct the coolant flow, excluding the occurrence of stagnant zones and local overheating of heating surfaces, high speeds and turbulization of the water flow minimize the formation of scale, KVm 1.25 boilers operate reliably without special measures for chemical water treatment. Technical characteristics of the KVm 1.25 hot water boiler with ZP RPK Boiler power, Gcal / h (MW) < / td> 1.25 (1.44) Heated area with a ceiling height of 3 m, m² 12500 Fuel, coal Kuznetskiy D Kharanorskiy B1 Net calorific value 5230 2720 Boiler efficiency, not less,% 83 76 Fuel consumption, kg / h 287 302 Equivalent fuel consumption, kg / h 215 Outgoing gas temperature azov, ° C Not more than 200 Consumption of working medium, m³ / h 50 Water temperature, ° C 70-95 Working medium pressure, MPa (kgf / cm²) 2.5-6 Boiler hydraulic resistance at a temperature difference of 25 ° C, MPa (kgf / cm²), no more than 0.007 (0.7) Aerodynamic resistance, Pa (mm. water column), Combustion mirror area, m2 no more than 230 Combustion device KVm firebox ZP RPK Overall dimensions of the boiler block with a firebox, no more Length, mm 3400 Width, mm 1800 Height, mm 2350

Котел КВм 0,6В конструкции котла КВм 0,6 (КВм 0,7) заложено:высокий КПДэффективность сжигания топливаэкономичностькомпактностьнадежностьудобство эксплуатацииповышенная ремонтопригодностьпростота монтажабезнакипностьТвердотопливный водогрейный котел КВм 0,6 ГКал под механическую топку отличает высокий КПД, что достигается за счет применения следующих конструктивных решений. Большой объем топочной камеры обеспечивает полное выгорание топлива, снижая тем самым потери с механическим недожогом. Газоплотное исполнение топки и качественная теплоизоляция снижают потери тепла через стенки котла и окружающую среду и исключают присосы холодного воздуха в топку котла. Развитая конвективная поверхность нагрева обеспечивает снижение температуры уходящих газов из котла до 200 - 180 °С.Применение современной технологии сжигания топлива в слое снижает потери с механическим и химическим недожогом топлива. Гидравлическая схема в водогрейном твердотопливном котле длительного горения работает по схеме противотока и конвективный пакет выступает в роли экономайзера. Многочисленные перегородки, установленные в коллекторах котла, направляют поток теплоносителя, исключая возникновение застойных зон и локальный перегрев поверхностей нагрева, высокие скорости и турбулизация потока воды максимально снижают образование накипи, котлы КВм с шурующей планкой надежно работают без специальных мероприятий по химводоподготовки.Технические характеристики водогрейного котла КВм 0,6Мощность водогрейного котла, Гкал/ч (МВт)0,52 (0,6)Отапливаемая площадь при высоте потолка 3 м, м²6000Топливо, угольКузнецкий ДХаранорский Б1Низшая теплота сгорания52302720КПД котла, не менее, %8273Расход топлива, кг/ч124302Расход условного топлива, кг/ч93Температура уходящих газов, °CНе более 200Расход рабочей среды, м³/ч21Температура воды, °C70-95Давление рабочей среды, МПа (кгс/cм²)2,5-6Гидравлическое сопротивление котла при перепаде температур 25°C, МПа (кгс/cм²),не более 0,007 (0,7)Аэродинамическое сопротивление, Па (мм.вод.ст.), Площадь зеркала горения, м²не более 220Топочное устройствотопка РПКГабаритные размеры котельного блока с топкой, не более Длина, мм2200Ширина, мм1450Высота, мм2000

KV 0.4 boiler The design of the KV 0.4 (KV 0.47) boiler includes: high efficiency < / li> fuel combustion efficiency economical compactness reliability ease of use increased maintainability ease of installation no scale Solid fuel hot water boiler KV 0.4 Gcal is characterized by high efficiency, which is achieved through the use of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface provides a decrease in the temperature of flue gases from the boiler to 200 -180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of fuel. The hydraulic circuit in the hot water boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler manifolds direct the coolant flow, eliminating the occurrence of stagnant zones and local overheating of heating surfaces. High speeds and turbulization of the water flow minimize the formation of scale, the boilers operate reliably without special measures for chemical water treatment. Technical characteristics of the KV 0.4 hot water boiler Name Boiler 0.4 Power of a hot water boiler, Gcal / h (MW) 0.4 (0.47) < / tr> Heated area with a ceiling height of 3 m, m² 4000 Fuel, coal stone brown Net calorific value 5230 2720 Boiler efficiency, not less,% 82 74 Fuel consumption , kg / h 94.7 205 Equivalent fuel consumption, kg / h 69 Flue gas temperature, ° C No more than 200 < tr> Consumption of working medium, m³ / h 16 Water temperature, ° C 70-95 < tr> Working medium pressure, MPa (kgf / cm²) 3.0-6.0 Hydraulic resistance boiler at a temperature difference of 25 ° C, MPa (kgf / cm²), no more 0.07 (0.7) Aerodynamic resistance, Pa (mm.WC) no more than 135 Combustion mirror area, m2 1,1 Overall dimensions of the boiler block with a furnace, no more Length, mm 2100 Width, mm 1400 Height, mm 1800

KV 0.2 boiler The design of the KV 0.2 (KV 0.23) boiler includes: high efficiency < / li> fuel combustion efficiency economical compactness reliability ease of use increased maintainability ease of installation no scale Solid fuel hot water boiler KV 0.2 Gcal is characterized by high efficiency, which is achieved through the use of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. The gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the heating steel boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 200-180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of fuel. The hydraulic circuit in an industrial steel heating boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the collectors of a water boiler direct the flow of the coolant, eliminating the occurrence of stagnant zones and local overheating of heating surfaces. High velocities and turbulization of the water flow minimize the formation of scale, boilers operate reliably without special measures for chemical water treatment. Technical characteristics of the KV 0.2 hot water boiler Power of the hot water boiler, Gcal / h (MW) 0.2 (0.23) Heated area with a ceiling height of 3 m, m² 2000 Fuel, coal stone brown Net calorific value 5230 2720 Boiler efficiency, not less,% 80 73 Fuel consumption, kg / h < / td> 48 104 Equivalent fuel consumption, kg / h 35 < / td> Flue gas temperature, ° C Not more than 200 medium, m³ / h 8 Water temperature, ° C 70 -95 Working medium pressure , MPa (kgf / cm²) 2.5-6 Boiler hydraulic resistance at a temperature difference of 25 ° C, MPa ( kgf / cm²), no more than 0.05 (0.5) Aerodynamic resistance, Pa (mm.w. st.), Combustion mirror area, m2 no more than 30 Combustion device Grate Overall dimensions of the boiler block with a furnace, no more Length, mm 1050 Width, mm 1300 < / td> Height, mm 2200

KV 0.15 boiler The design of the KV 0.15 (KV 0.17) boiler includes: high efficiency < / li> fuel combustion efficiency economical compactness reliability ease of use increased maintainability ease of installation no scale The hot water boiler KV 0,15 Gcal is characterized by high efficiency, which is achieved through the use of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 200-180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of fuel. The hydraulic circuit in a hot water boiler works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler manifolds direct the coolant flow, eliminating the occurrence of stagnant zones and local overheating of heating surfaces. High velocities and turbulization of the water flow minimize the formation of scale, hot-water solid fuel boilers for long burning work reliably without special measures for chemical water treatment. Technical characteristics of the KV 0.15 Gcal boiler Power of a hot water boiler, Gcal / h (MW) 0.15 (0.17) Heated area with a ceiling height of 3 m, m² 1500 Fuel, coal stone brown Net calorific value 5230 2720 Boiler efficiency, not less,% 80 73 Fuel consumption, kg / h 45 76 Equivalent fuel consumption, kg / h 27 Flue gas temperature, ° C No more than 200 < td> Working medium flow rate, m³ / h 6 Water temperature, ° C 70-9 5 Working medium pressure, MPa (kgf / cm²) 2.5-6 Hydraulic resistance of the boiler at a temperature difference of 25 ° C, MPa (kgf / cm²), no more than 0.05 (0.5) < / tr> Aerodynamic resistance, Pa (mm.WC), Combustion mirror area, m2 no more than 80 Combustion device KVr firebox Overall dimensions of the boiler block with a firebox, no more < td colspan = "2"> Length, mm 950 Width, mm 1300 Height, mm 2050

Main functions: automatic shutdown of the boiler when the pressure and temperature of the water leaving the boiler increase; manual remote shutdown of the boiler; light and sound signaling deviations of technological parameters from the norm and memorizing the root cause of the accident; remote start, stop and light indication of the operation of draft machines; control of temperature and pressure of water at the boiler outlet. The control panel of the KVr coal-fired hot water boiler has several versions: The control panel of the KVr boiler. Option 1 indicator lights and loud bang bell. Signals that the main parameters of the boiler operation are exceeded temperature and pressure; vacuum sensor in the furnace (flue); Boiler control panel KVr. Option 2 indicating devices with the display of the boiler operation parameter on the control panel display; temperature; vacuum sensor in the furnace (gas duct ); Boiler control panel KVR. Option 3 indicating devices with the display of the main parameters of the boiler operation on the control panel display; temperature and pressure; vacuum sensor in furnace (flue)

TShPM-1.45

Cast iron grates 880 * 220 are used in the furnaces of hot water and steam boilers of low power and are installed directly in the furnace part of the boiler on the ledges of the side walls and grate beams. Their purpose is to support the layer of solid fuel and improve the supply of oxygen to the combustion area. Openings are made in the grates 880x220, which are for supplying air to the fuel layer and the furnace, and for screening out the formed coal and ash into the ash pan. Stiffening ribs are made at the bottom of the grate. Grate grates are assembled from cast iron slab grates.

The door of the combustion boiler Bratsk is installed in boilers Bratsk, hot water boilers KVr, KVm, steam boilers, as grooves for furnace mechanical furnaces.

The smoke exhauster is a draft machine that is designed to remove flue gases - products of fuel combustion. Moving gases in the right direction is the primary task of the DN smoke exhauster. By creating the required draft in the boiler, the required performance of the boiler unit develops. Hot water and steam boilers are equipped with smoke exhausters. The smoke exhauster is designed for continuous operation with a long resource. It can be installed indoors or outdoors. The minimum temperature at which the smoke exhauster can operate is -30 ° C, the maximum one is up to 200 ° C. The smoke exhausters of right or left rotation are manufactured. If you look at the DN 3.5 / 1500 smoke exhauster from the side of the electric motor, and the rotation of the boiler smoke exhauster impeller will be counterclockwise, this will be considered counterclockwise rotation. Right-hand rotation - when the rotation of the impeller of the exhauster is performed in the clockwise direction. The main characteristics of the exhauster are performance and pressure. These parameters are controlled by an axial guide vane or a suction pocket with a gate. The suction pocket brings gases to the impeller blades more evenly and eliminates flow swirling, respectively, the efficiency of the smoke exhauster increases. The impeller is equipped with a hub to protect the bearings. The DN 3.5 / 1500 smoke exhauster can have a basic or simplified configuration, and they are also equipped with systems for efficient ash collection. The durability of the smoke exhausters is ensured by the thickened walls of the snail.

The smoke exhauster is a draft machine that is designed to remove flue gases - products of fuel combustion. Moving gases in the right direction is the primary task of the DN smoke exhauster. By creating the required draft in the boiler, the required performance of the boiler unit develops. Hot water and steam boilers are equipped with smoke exhausters. The smoke exhauster is designed for continuous operation with a long resource. It can be installed indoors or outdoors. The minimum temperature at which the smoke exhauster can operate is -30 ° C, the maximum one is up to 200 ° C. The smoke exhausters of right or left rotation are manufactured. If you look at the DN 3.5 / 1500 smoke exhauster from the side of the electric motor, and the rotation of the boiler smoke exhauster impeller will be counterclockwise, this will be considered counterclockwise rotation. Right-hand rotation - when the rotation of the impeller of the exhauster is performed in the clockwise direction. The main characteristics of the exhauster are performance and pressure. These parameters are controlled by an axial guide vane or a suction pocket with a gate. The suction pocket brings gases to the impeller blades more evenly and eliminates flow swirling, respectively, the efficiency of the smoke exhauster increases. The impeller is equipped with a hub to protect the bearings. The DN 3.5 / 1500 smoke exhauster can have a basic or simplified configuration, and they are also equipped with systems for efficient ash collection. The durability of the smoke exhausters is ensured by the thickened walls of the snail.

The hot water boiler KVr ​​0.7 Gcal is distinguished by high efficiency, which is achieved through the use of the following design solutions. The large volume of the combustion chamber ensures complete combustion of fuel, thereby reducing losses with mechanical underburning. Gas-tight design of the furnace and high-quality thermal insulation reduce heat losses through the walls of the boiler and the environment and exclude the suction of cold air into the boiler furnace. The developed convective heating surface ensures a decrease in the temperature of flue gases from the boiler to 200-180 ° C. The use of modern technology of fuel combustion in the bed reduces losses with mechanical and chemical underburning of fuel. The hydraulic circuit in a hot water solid fuel boiler for long burning works according to the counterflow circuit and the convective package acts as an economizer. Numerous partitions installed in the boiler headers direct the coolant flow, excluding the occurrence of stagnant zones and local overheating of heating surfaces, high speeds and turbulization of the water flow minimize the formation of scale, steel boilers operate reliably without special measures for chemical water treatment. Technical characteristics of the KVr 0.7 hot water boiler Boiler power, Gcal / h (MW) 0.6 (0.7) Heated area with a ceiling height of 3 m, m² 6000 < / td> Fuel, coal Kuznetskiy D Kharanorskiy B1 Lower heat combustion 5230 2720 Boiler efficiency, not less,% 82 73 Fuel consumption, kg / h 144 302 Equivalent fuel consumption, kg / h 108 Exhaust gas temperature, ° C 200 Consumption of working medium, m³ / h 24 Water temperature, ° C 70-95 Working medium pressure, MPa (kgf / cm² ) 0.3-0.7 (3-6) Boiler hydraulic resistance at a temperature difference of 25 ° C, MPa (kgf / cm²), no more than 0.07 (0.7) Aerodynamic resistance, Pa (mm.water .st.), Combustion mirror area, m2 no more than 300 Combustion device grate Overall dimensions of the boiler block with a firebox, no more Length, mm 2300 Width, mm 1450 Height, mm 1800

• Productivity of RBU: 60 cubic meters. meters per hour • Production of two grades of concrete at the same time • Twin-shaft concrete mixer V = 750 liters - 2 pieces • Fully automatic control of RBU • Production of ready-mixed concrete and reinforced concrete products (vibropress) simultaneously • The equipment is certified, the certificate of conformity GOST 27338-93 and GOST 16349-85 • Full 1 year warranty

As a rule, for many enterprises using gaseous oxygen in technological processes, its purity is of great importance. To resolve this issue, the employees of ZEPRIKON CJSC offer enterprises to use their oxygen stations with an oxygen output of 99 (± 1)%. This purity is achieved through the use of state-of-the-art oxygen production methods using pressure swing adsorption.

Для заправки большого количества баллонов и снабжения потребителей кислородом в больших объёмах спроектирована модульная кислородная станция для заправки 100 баллонов. Данная станция представлена в трёх исполнениях и может работать в следующих режимах:1. заправка 100 кислородных баллонов в течение 8 часов; 2. заправка 100 кислородных баллонов за 18 часов; 3. заправка 100 кислородных баллонов за 24 часа. Исходя из потребности заказчиков и их режимов работы, каждый клиент может получить свою кислородную станцию. При этом чистота кислорода может регулироваться в диапазоне от 93 до 98%.

For remote oxygen consumers, as well as for organizations that want to organize independent production of gaseous oxygen with its injection into cylinders, it offers a solution in the form of modular oxygen stations for filling cylinders. This equipment is specially equipped with a booster compressor and a ramp for filling cylinders. As a result, at the exit you get cylinders filled with gaseous oxygen, ready for operation.

This equipment is based on the technology of short-cycle adsorption to separate air and obtain gaseous nitrogen at the outlet. This technology allows us to receive nitrogen at the outlet of our stations with a purity of up to 99.9995%. Our adsorption nitrogen stations produce nitrogen with a capacity of 20 to 8000 m3 / min and an outlet pressure of 3 to 150 bar. The stations can be made in a stationary (on a frame), modular design, on a chassis, on a sled.

For supplying remote objects, as well as large industrial enterprises with compressed air, ZEPRIKON CJSC offers the optimal solution - modular air compressor stations. This type of equipment allows you to organize an autonomous supply of compressed air to the consumer, regardless of its location. A distinctive feature of modular air compressor stations is that all technological equipment is mounted in a container, in which they function as a single system. The power source for the operation of the station is the electrical network, as well as a specially installed diesel generator. Modular air compressor stations create a maximum compressed air capacity of up to 120 m3 / min and a maximum working pressure of up to 4.0 MPa.

Mobile nitrogen station ZEPRIKON CJSC is an autonomous operating unit for the production of gaseous nitrogen. This station is based on a diesel compressor or diesel generator, which allows the station to operate without being connected to the mains. All equipment is mounted on a car chassis or installed in a metal container. Mobile nitrogen stations of ZEPRIKON CJSC allow to obtain nitrogen up to 3000 m3 / h and purity up to 99.99%. The control system of this station allows you to control all processes and equipment from one control panel and immediately set the required operating modes and characteristics of the final product.

CJSC "ZEPRIKON" designs and manufactures block-type water compressor stations of medium and high performance according to the customer's specifications. A distinctive feature of this type of station is the placement of all technological equipment in a special building - block box. The advantage of the equipment is the absence of the need to build a building for compressor equipment, the autonomy of the compressor station, high productivity, low maintenance and operation costs.

Contact Fast Freezer "KSA - 3500-12 / 1100" is designed for contact freezing of injected parts of poultry. A thin HDPE (High Density Polyethylene) film is used as a supporting element, sliding over a cooled aluminum plate in which the refrigerant circulates. This type of film is approved for contact with food. The offered equipment is fully equipped and ready to work, it is enough to connect it to the power supply and refrigerant. A complete refrigeration unit can be offered as an option. The equipment is made on a stainless steel frame with adjustable feet for precise height adjustment. All structural elements (with the exception of contact plates, which are made of aluminum), conveyor rollers, housing, etc. made of stainless steel AISI-304, and the drive rollers and shafts are coated with a polymeric coating approved for contact with food. As a drive of the film, a motor with a variable, constantly controlled rotation transmission speed is used. The spent film is wound onto a reel using a transfer coupled to the main drive. A control panel made of stainless steel is installed on the supporting frame of the equipment. The panel contains the following elements: drive motor control unit, start / stop buttons, main switch, emergency stop button and freezer plate temperature sensor.

The sorting system includes: an automated conveyor system controlled by a controller; barcode scanning system; actuators that move the product to the appropriate cells designed to work with a specific type of product. The system is designed based on the number of product types, space-planning solutions of the production site and possible additional requirements for the technological process.

Кулер для охлаждения хлеба, кондитерских изделий Lipsia представляет собой спиральный кулер с центральным барабаном, позволяющий полностью автоматизировать процесс охлаждения хлеба. Преимущества: • Высокая производительность; • Сравнительно небольшой размер; • Возможность непрерывной эксплуатации в течение продолжительного промежутка времени. Кулер для охлаждения хлеба имеет центральный или боковой привод. Как правило, продукция поступает на верхний ярус. Для контроля высоты продукта на входе устанавливают шибер с концевым датчиком.

Оборудование для лимонадов в розлив "Ретро" продается в комплектациях с тремя / шестью колбами в виде конуса из стеклопластика или ударопрочного стекла. В комплект входит сатуратор, собранная колонна для розлива напитков, комплектующие для газового болона и стойки.

Линия разделки птицы предназначена для разделки тушек кондиционной птицы (бройлеров, кур, цыплят) на следующие части: крылья, грудка, спинка, окорочка (с частью спинки или без частей спинки), бедро, голень. Производительность 3000 шт/час. Модульная конструкция линии для разделки птицы позволяет более полно удовлетворить потребности заказчика в выпуске продукции пользующейся спросом. Линия состоит из следующих узлов: Рама Приводная станция -1,5кВт Натяжная станция Модуль отрезания крыльев – 2х1,5 кВт Модуль отрезания грудки 2х1,5кВт Модуль отрезания спинки 1,5кВтМодуль отрезания окорочков и спинки 2х1,5кВт Модуль разделения на бедро-глень 2х1,5кВт Устройство сброса голени Поворотная подвеска Пульт управления

Рукавные линии - предназначены для изготовление многослойной заготовки мешка с нанесением изображения от 2 до 6 цветов с поеречной и продольной проклейкой. Производительность линий в зависимости от модификации, от 50 до 120 м/мин. Управление с пульта управления (сенсорный экран). Тестирование и контроль можно осуществлять дистанционно. Преимущество линии - это увеличенный формат бумаги до 1300 мм, что позволяет изготавливать мешки любого востребованного формата.

CNC milling machine Sale | Manufacturing | Production of any CNC machine tools A milling machine from the "ChPU24RF" Company is designed for high-quality milling and engraving of surfaces of parts and workpieces on a plane (2D) and in three-dimensional space (3D) Application area: advertising production, furniture production, interior and exterior decoration, exclusive products, door production, model production, artistic parquet production, facades Types of processed materials: Soft and hard wood, composite materials (plywood, chipboard, fiberboard, MDF, etc.), plastic, non-ferrous metal, acrylic glass

Vibropress Monolit-100, a simple, inexpensive and reliable machine for the production of small-sized concrete products by the method of semi-dry vibrocompression, it is completed with parts and units from domestic agricultural machinery, which means that after the warranty service will not become a problem for the owner either in price or in time to find the necessary details. The molding zone of the machine, in contrast to many competitors in this class, is -1000 mm, this allows the vibropress to be made the most popular vibropressed product that is in great demand on the market - road curbs and sidewalk curbs 1 meter long. Also, the vibropress can make wall blocks 39x19x19 (cm) with two or four voids, a partition wall block 39x12x19 (cm), a small sidewalk border 50x5x20 (cm) and other concrete products at the request of the customer.

Manual loading of concrete mix. The width of the forming zone is 800 mm. The vibrating press is designed for the production of wall blocks with a size of 390x190x190 mm, two-hollow or four-hollow (depending on the type of installed punch-matrix elements), partition blocks with a size of 390x100x190 mm (in the presence of the required type of punch-matrix elements). The products are molded onto technological replaceable wooden pallets. The productivity of the vibrating press is 20-30 molding cycles per hour. The number of molded products per cycle: wall block - 4 pcs., Partition block - 5 pcs. The recommended number of serviced personnel is 2 workers. Unit size without oil station and concrete mixer: length 1500 mm, width 1700 mm, height 1950 mm. Installation weight 950 kg. Scope of delivery: vibropress, oil station, hydraulic pallet pusher for transferring the pallet with molded products onto removable multi-level racks. Shaping tooling punch-matrix "two-hollow wall block 4 blocks" is included in the delivery set. Form-forming elements punch-matrix "wall block with four hollow blocks 4 blocks", and "two-hollow partition wall block 5 blocks", concrete mixer, technological pallets are supplied for an additional fee. The installed electric power of the vibrating press is 7.5 kW, voltage is 380 V. size 1500x1700x1950 mm

Бетоносмеситель СБМ-550(две в одной) двуполостной смеситель принудительного действия с горизонтальным расположением вала. Габаритные размеры 2450х1500х1550 мм. Масса 1450 кг. СБМ-550 (две в одной) это уникальный бетоносмеситель, созданный специально для одновременного приготовления двух разных по составу и цвету замесов бетона для производства двухслойной тротуарной плитки методом вибролитья и в некоторых случаях вибропрессованных бетонных изделий, где так же используется технология многослойного формования . Бетоносмеситель СБМ-550 (две в одной) по, сути, является двумя разными бетономешалками интегрированными в общий корпус и работающими от общего привода. Первая (меньшая) полость бетоносмесителя способна приготовить готовый раствор в количестве не менее 160 литров, вторая (большая) не менее 400 . Каждая полость имеет свой собственный выгрузной люк, а места выгрузки готового раствора на выходе для предотвращения смешивания разных по составу бетонов разделены специальной перегородкой.

The equipment for the production of carved candles is offered in the semi-professional and professional segment. The first is represented by small wax melters of the Hobby and MonoWax series (from 1 container for melting paraffin to 10), the second - Business wax melters (up to 12 containers).

Balanced sets of equipment and silicone molds for the production of candles (Mini-pack and hobby-pack) will allow you to make cut, other types of candles. They consist of a wax melter, silicone mold sets, wicks, dyes and varnish (depending on the model).

Весы крановые подвесные электронные К ВИД(Ж)А «Металл 1» предназначаются для взвешивания продукции. Корпус выполнен из алюминия. Жидко-кристаллический индикатор, пульт ДУ. Завод «Мидл» производит 8 моделей. Минимальный вес 4 кг, максимальный 2000 кг. Крюк вращается на 360 град. Изделия оснащены аккумуляторными батареями. Рассчитаны на электросеть 220 Вольт.

Advantages of the UPK-14PRGK cable rewinding device with RKU: A technological reel is supplied as standard, which allows winding cables weighing up to 300 kg and centering sleeves. The receiving stand is equipped with a hydraulic lift for lifting and lowering drums with a cable, which allows the cable to be unwound without the involvement of lifting mechanisms. The presence of wheel supports allows the operator to easily move the machine around the warehouse. The presence in the design of the Device for cable rewinding of the cable layer allows to obtain a tighter laying of the rewound material. The machine is equipped with a SEW-Eurodrive geared motor. The frequency converter allows you to smoothly change the rewinding speed from 4 to 60 rpm. Availability of the option to stop when reaching the programmed length Protection of the electric motor against voltage surges, short circuits, overheating. The device for cable rewinding UPK-14PRGK with RKU is a middle-class machine with a manual cable-laying machine, designed for winding cable and wire products with a diameter of not more than 30 mm. The device for cable rewinding UPK-14PRGK with RKU is designed to use cable reels from 8 to 14 numbers, as well as up to 14 drum numbers with the use of centering sleeves.

Устройство намотки кабеля УПК-25 РЧ003 - новый модифицированный станок тяжелого класса предназначен для замены УПК-25РЧ002. Устройство обеспечивает намотку кабельно-проводниковой продукции диаметром до 65 мм на барабаны максимальным весом до 3 тонн. Диапазон используемых кабельных барабанов с 10 по 22 типоразмер. Станок для перемотки кабеля УПК-25 РЧ003 запатентован. Измерительный узел ИДМ имеет патент и сертификат об утверждении типа средств измерения Выпускаются различные модификации станка: С РКУ - ручным кабелеукладчиком; С АКУ - автоматическим кабелеукладчиком; C R97 - вариант исполнения с усиленным редуктором; С ИДМ - возможны различные модификации измерителя длины серии ИДМ Преимущества Устройства для перемотки кабеля на барабаны УПК-25РЧ003: в качестве дополнительной комплектации может поставлятся технологический барабан, позволяющий наматывать кабель массой до 300 кг наличие в конструкции станка кабелеукладчика позволяет получать более плотную укладку. При комплектации с АКУ - автоматическим кабелеукладчиком - обеспечивается ровная укладка перематываемого материала без привлечения оператора. Плавный пуск. Преобразователь частоты позволяет плавно изменять скорость перемотки от 0 до 30 оборотов в минуту. Реверсивное вращение. Измеритель длины реверсивный. Наличие опции звукового сигнала и автоматического останова при достижении запрограммированной длины. В стандартной комплектации предусмотрен сетевой дроссель для стабилизации напряжения. Защита электродвигателя от скачков напряжения, короткого замыкания, перегрева.