商品描述
修补混合物 用于混凝土 洲际弹道导弹300 预约 : 干混建筑料MBR 300用于制备建筑细粒混凝土,用于修补混凝土结构,单缝,技术孔,密封裂缝等。 组成 : 干式建筑拌料MBR 300 是通过分馏的沙子,波特兰水泥和改性添加剂复合物的强烈混合而获得的聚合物-矿物细粒混合物。 混凝土制备 : 用于干燥建筑混合物MBR 300 倒入干净的淡水中,不断搅拌,直到用木铲,带有混合器喷嘴的电钻或低速强制混合器获得均匀的团块为止。混合进行至少5分钟。 制备混凝土所需的水量由每1千克干建筑混合物0.2-0.22 L的比例(每25千克干建筑混合物每袋5.5-5.75 L的水)确定。当达到工作所需的稠度,建筑混凝土的可塑性时,确定确切的水量。 准备好站立 搅拌5分钟以获得完全均匀,然后重新混合。 准备好的混凝土必须在1小时内使用。 准备工作表面(基础) : 工作表面(底座)必须坚固,耐用,并且没有灰尘,污垢,油脂,蜡,沥青,油漆残留物。裂缝被打破,旧的易碎混凝土被清除,释放的钢筋被清除锈迹。使用压缩空气清除准备好的表面上的灰尘。 聚合物矿物底漆加固的弱旧混凝土或砂浆 在底漆上涂一层高吸收性的表面。 金属零件必须用防腐溶液处理。 具体应用 : 在施加混凝土之前,准备好的表面要充分润湿。让水浸泡,然后手动施加混凝土。对于大面积的要维修的表面,在承受较大弯曲载荷的地方进行维修,必须使用耐碱的玻璃纤维网,金属增强材料或纤维来加固所施加的混凝土层,厚度超过50 mm的混凝土层。 直到完全完成为止或通过抓握,混凝土的铺设都不会间断。在涂覆后续层之前,有必要先润湿之前的层,即遵守加工方法-“湿湿”。 使用MBR300时,工作表面的温度应不低于+5ºС且不高于30ºС。 使用MBR300M时,工作表面的温度应至少为-10ºС,且不超过+5ºС。 混凝土消耗量取决于修补的类型。修复每1平方米要修复的95-110千克损坏的水平表面,层厚度为50毫米。 规格 : 颜色 灰色 涩 硅酸盐水泥 骨料 细砂 占位符分数 高达1.0毫米 保水能力 不少于98% 一轮最大厚度 50毫米 烹调用水 每1 kg混合物0.2-0.22 L 可行性 至少1小时 硬化时间 24小时 工作面温度 对于MBR-300 对于MBR-300M 从+5˚С到+30˚С 从-10˚С到+5˚С 抗压强度(等级) 300 kgf / m 2 (30兆帕) 从混凝土表面剥离的强度 18 kgf / m 2 (1.8兆帕) 防冻性 不少于400次循环 安全注意事项 : 当与水相互作用时,混合物中所含的波特兰水泥会形成碱。避免在皮肤和粘膜上沾上现成的砂浆。如果发生接触,请用干净的自来水冲洗接触区域。 保质期 : 将砂浆存放在相对湿度为60%,温度为–50至+50˚С的干燥地方。从制造日期算起,制造商包装中的保质期为6个月
详情
同类产品
DINIL PLUS
Узбекистан
USD
0.6/个/件/只
0.6
Вентиляционная решетка пластиковая- круглая отлично подходит для прикрытия отверстия в стене, в потолке или для закрытия вентиляционного канала Изготовлена из качественного материала ABS. Экологически чистая, прочная. Для подключения к круглым воздуховодам 125 мм, монтаж с помощью монтажного фланца
DINIL PLUS
Узбекистан
USD
0.8/个/件/只
0.8
Люк ревизионный пластиковый 200х300 мм Люк-дверца ревизионный пластиковый с ручкой. Для доступа к скрытым узлам и инженерным коммуникациям. Предназначен для установки в стене или потолке. Оснащен ручкой для удобства открытия/закрытия люка. Возможно использование во влажных помещениях. Простой уход. Монтаж осуществляется при помощи раствора или клея.
Best Choice Ukraine
Киев, Украина
USD
6.32/个/件/只
6.32
Garden path mold Round Stones 80x80x6 cm
Garden paths create a chic view of the suburban area, which add tidiness and nobility.
Concrete paths are durable and very practical. They are not afraid of any atmospheric conditions and are easy to clean.
At the present time, it is possible to make a concrete path with your own hands using special forms. Such a path will not only create comfort and coziness, but also emphasize the design of your site.
Drawing - an imitation of natural stone will help to create a mold for making a garden path. Round Stones 80x80x6 cm. This plastic mold consists of 9 cells that have an arbitrary shape and are connected together. They form a certain pattern, while the shape is designed in such a way that it allows the slabs to be joined together in any direction, to obtain tracks of the required width, as well as to make turns (bends), while the joints are absolutely indistinguishable.
It is also possible to adjust the color scheme of the garden path using various additives. With this form, you can easily decorate the paths in the garden or playground and you will be satisfied with the work done with your own hands.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the shape for the garden path Round stones:
Manufacturer: Hormusend
Country of origin: Ukraine
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 1.56 pcs
Pattern: round stones
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Number of stones in the form: 9 pcs
Finished board height: 60.0 mm
Finished stone height: 60.0 mm
Volume: 40 l
Length: 800.0 mm
Width: 800.0 mm
Height: 60.0 mm
Weight: 1.6kg
Volume weight: 9.6 kg
Best Choice Ukraine
Киев, Украина
USD
4.5/个/件/只
4.5
Garden path mold Castle Stone 60x60x6 cm
It has become easier to create comfort and coziness in the garden. You can make an unusual geometric design, similar to a composition from a natural stone, without a lot of time. You don't need to match each item individually. Simply pour the solution into the garden mold. From the resulting slabs, you can easily create a decorated walkway.
The garden path mold will serve you for a long time, as it is made of wear-resistant polypropylene. You can always use it to create an additional pedestrian zone in the garden.
The walkway will emphasize the design of your site, as the pattern is similar to a natural stone composition.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the mold for the garden path Castle Stone:
Manufacturer: Hormusend
Country of origin: Ukraine
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Pattern: imitation of a wild stone
Number of stones in the form: 9 pcs
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 2.78 pcs
Finished board height: 20.0 mm
Finished stone height: 40.0 mm
Length: 600.0 mm
Width: 600.0 mm
Height: 60.0 mm
Weight: 1.7kg
Best Choice Ukraine
Киев, Украина
USD
5.54/个/件/只
5.54
Garden path mold Castle Stone 60x60x6 cm with handles
An integral element of a well-groomed garden is a garden path, which allows you to comfortably move through it and not worry about the ground sticking to your shoes.
With minimal knowledge of construction and little effort, it is easier to pour a concrete path than to lay tiles. To make it as quickly and easily as possible, use a unique modern development - a special stencil that looks like cells that realistically imitate natural stones.
An unusual geometric design will allow you to make an easy-to-use shape for a garden path Castle Stone 60x60x6 cm with handles.
The garden path mold is made of wear-resistant polypropylene and is equipped with 2 handles for convenience. You just need to pour the solution into it, and after partial hardening, the form can be removed. Provided manufacturer's warranty for up to 1000 pouring cycles.
For a unique design, it is recommended to add a color pigment directly to the solution.
Benefits of using a garden path mold:
Quickness of manufacture - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the mold for the garden path Castle Stone:
Manufacturer: Hormusend
Country of origin: Ukraine
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Pattern: imitation of a wild stone
Number of stones in the form: 9 pcs
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 2.78 pcs
Finished board height: 20.0 mm
Finished stone height: 40.0 mm
Length: 600.0 mm
Width: 600.0 mm
Height: 60.0 mm
Weight: 1.7kg
Best Choice Ukraine
Киев, Украина
USD
3.68/个/件/只
3.68
Form for a garden path Old Town 60x40x6 cm
A garden path on the site not only creates a beautiful view and comfort, but also is an excellent protection for your shoes from the ground, dirt and dust.
Thanks to modern technologies, it is possible to make the coating independently, which gives complete confidence in its quality.
Plastic mold Old City 60x40x6 cm for laying a concrete path will help you to model and lay your garden path or playground in the shortest possible time.
It is reusable, made of durable material - polypropylene. On the slab there are 9 decorative stones 11x18cm, the seam depth is 2 cm. The wall thickness is 4 mm, the edging of the stone is 2 mm. In places of loading, stiffeners are implemented, which allows it to withstand 1000 moldings.
To use it, it is enough to prepare a concrete solution. The shape fits well on either side, allowing you to make the track seamless.
If we compare the total costs, then a do-it-yourself garden path made of concrete, obtained using a form, will cost less than laying tiles or pebbles.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the form for the garden path Old Town:
Manufacturer: Hormusend
Country of origin: Ukraine
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 4.17 pcs
Pattern: Old Town
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Number of stones in the form: 9 pcs
Finished board height: 60 mm
Finished stone height: 60 mm
Length: 600.0 mm
Width: 400.0 mm
Height: 60.0 mm
Best Choice Ukraine
Киев, Украина
USD
3.68/个/件/只
3.68
Garden path mold Universal Stone 60x40x6 cm
A beautiful view of the countryside provides a decor that should be combined with the rest of the garden. Its main element is a practical and unique garden path or playground, which can be easily modeled and created with your own hands using plastic molds and a concrete grout.
An excellent solution for a plot that is decorated in a strict, classical or modern style would be the use of an unusual shape for the garden path Universal Stone 60x40x6 cm, the design of which is designed for convenient work with concrete.
It is a sturdy and secure shape with strong edges. Its feature is the presence of technological holes for handles, which is convenient when pouring large areas. During the first molding, special cavities in the inner seam are filled with mortar, which gives the form additional strength.
The drawing of the shape is two large and two small triangles. The outer frame is made in such a way that it can be easily docked even with molds from other manufacturers.
For the uniqueness of the design, it is possible to adjust the color scheme of the garden path with the help of various additives.
By making your own coating, you will be sure not only of its quality, but also of budget savings.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the form for the garden path Universal Stone:
Manufacturer: Hormusend
Country of origin: Ukraine
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 4.17 pcs
Pattern: universal stone
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Number of stones in the form: 4 pieces
Finished board height: 60 mm
Finished stone height: 60 mm
Length: 600.0 mm
Width: 400.0 mm
Height: 60.0 mm
Weight: 1.0KG
这些类别的供应商
此类别中的所有供应商
商品:
供应商:
最少订单:
经理处
销售部门:
销售部门:
销售部门:
信息
告诉经理,您在Qoovee 上找到了商品
供应商联系人不可用!
写信给供应商