Construction Materials in bulk on Qoovee

- stress-relieving underlayment reduces impact noise safer on problem substrates very low emissions - EC1-PLUS Stress-relieving decoupling and impact attenuation boards for indoor and multi-layer parquet flooring and indoor and outdoor ceramic tiles and natural stone open air. The board is used specifically for problematic substrates. The Unitop disconnector plate is a very low emission (GEV-compliant) laying material that is purulent and rot-resistant. It can be used as a decoupling and impact noise reduction board on walls and floors in rooms under many cover materials for traffic loads up to 5 kN / m². Only the 4 mm slab is suitable for use in underfloor heating systems. White

cement binder frost resistance can be filled in gradients up to 3% stable and can be adjusted to flow. Powdery, plastic hardened, low tension, self-leveling, hydraulically set leveling compound. For indoor and outdoor use, especially for evening extreme unevenness such as hollow slabs and slabs, as well as large area level compensation up to 3% incline. Consumption about 1.6 kg / m² per layer thickness mm

high-calcined leveling compound fast drying extremely good flow very low emission, EC1-PLUS Self-leveling, flowable, pumpable, polymer-modified leveling compounds. Indoors only, for load-bearing cementitious screeds and concrete. For the production of flat substrates before laying all types of floor coverings, especially for extreme evening unevenness, up to 30 mm. Not suitable for commercial use or for driving motor vehicles. Consumption about 1.5 kg / m² per layer thickness mm

indoor and outdoor ready-to-use early strength Prefabricated, universally usable dry mortar for screed production Can be processed manually or by machine. It can be used as floating, grease-free or as a compound screed and is suitable as a heated screed without additional additives. Screed with high early strength and extremely low moisture content, which is also suitable for damp rooms, but not for very high sustained water loads. Consumption about 20 kg / m² / cm

with trass content very fast hardening high stability up to 50 mm in one layer Trass-containing, highly hardened, water and frost resistant, very fast hardening, hydraulically setting leveling mortar. Thanks to special additives, the mortar hardens without tension up to 50 mm and demonstrates very good processing properties. Indoors and outdoors for leveling uneven walls and floor areas before tiling. Consumption about 1.6 kg / m² per layer thickness mm

SCREADING CLAMPS

odorless fast hardening solvent free no mixer required Universal, fast hardening, solvent free, odorless 2K silicate resin based on PUR water glass with very good adhesion and ultimate strength. Indoors and outdoors for positive locking of working and compression joints as well as narrow and wide screed cracks as a quick mortar and adhesive for wood, stone, concrete and metal. Consumption from 1.3 to 1.5 kg per liter of articular space, about 100 ml / running meter of a narrow screed crack, depending on the width and depth of the crack Color Comp.Yellow - Comp.B brown

- high moisture barrier Emicode EC1 Plus / extremely low emission solvent-free / Giscode RE1 odor reduction High quality, low emission, two-component epoxy resin system for blocking moisture on cement screed and concrete. To block excess residual moisture in the room up to 6 CM% in concrete substrates and cement screeds. Consultation is required for use with underfloor heating systems. Consumption depending on the field of application: 200 - 600 g / m²; as a moisture barrier: 450 g / m², as an EP mortar: approx. 0.3 kg / m² for each mm of layer thickness

- high moisture barrier Emicode EC1 Plus / extremely low emission solvent-free / Giscode RE1 odor reduction High quality, low emission, two-component epoxy resin system for blocking moisture on cement screed and concrete. To block excess residual moisture in the room up to 6 CM% in concrete substrates and cement screeds. Consultation is required for use with underfloor heating systems. Consumption depending on the field of application: 200 - 600 g / m²; as a moisture barrier: 450 g / m², as an EP mortar: approx. 0.3 kg / m² for each mm of layer thickness

- EC1 - very low emission blue, solvent free, ready to use High quality synthetic resin dispersion with very good penetration properties and easy handling due to its blue color. Indoors and outdoors as an adhesive bridge for all adhesives, leveling compounds and compound seals for absorbent substrates. Suitable according to ÖNORM B 3407 W1 - W2. Consumption about 150 g / m² Color blue

- EC1 - very low emission blue, solvent free, ready to use High quality synthetic resin dispersion with very good penetration properties and easy handling due to its blue color. Indoors and outdoors as an adhesive bridge for all adhesives, leveling compounds and compound seals for absorbent substrates. Suitable according to ÖNORM B 3407 W1 - W2. Consumption about 150 g / m² Color blue

is a versatile one-component EC1 very low emission fast drying primer filled with quartz sand tiles on tiles Adhesive, solvent-free, one-component, ready-to-use, very fast drying primer based on a special dispersion. A non-slip surface is achieved after drying. Indoor and outdoor for walls and flooring. For the preparation of absorbent and non-absorbent substrates. Suitable both before smoothing with Murexin leveling compounds and before laying tiles; specially for repairing tiles on tiles. Supergrund D4 Rapid can be used as a primer on anhydrite screeds up to 10,000 cm² (eg 100 x 100 cm) (More in the section “For a perfect system”). Suitable according to ÖNORM B 3407 W1 - W2. Consumption 100 - 150 g / m² depending on the substrate Color yellow

is a versatile one-component EC1 very low emission fast drying primer filled with quartz sand tiles on tiles Adhesive, solvent-free, one-component, ready-to-use, very fast drying primer based on a special dispersion. A non-slip surface is achieved after drying. Indoor and outdoor for walls and flooring. For the preparation of absorbent and non-absorbent substrates. Suitable both before smoothing with Murexin leveling compounds and before laying tiles; specially for repairing tiles on tiles. Supergrund D4 Rapid can be used as a primer on anhydrite screeds up to 10,000 cm² (eg 100 x 100 cm) (More in the section “For a perfect system”). Suitable according to ÖNORM B 3407 W1 - W2. Consumption 100 - 150 g / m² depending on the substrate Color yellow

- fiber reinforced improved full hardening very good deformability excellent stability Powdery but fiber reinforced and dustproof, water and frost resistant, highly hardened, hydraulically settable flexible adhesive with improved full hardening for installation in thin layers. For the installation of indoor and outdoor ceramic wall and floor tiles, panels, fine ceramics, natural stones for increased thermal or static loads. Particularly suitable for tiling on tiles. Consumption consumption depending on the teeth: approx. 1.7 kg / m² with 6 mm teeth, approx. 2.3 kg / m² with 8 mm teeth, approx. 3.0 kg / m² with 10 mm notched teeth Color gray

light weight chemically resistant Light weight, excellent adhesion in a concrete matrix, does not resist compaction during compaction, Emodule adapts to the setting of concrete, does not corrode, is chemically resistant to acids and liquids. On concrete, cornices, screeds, garden walls, cellar walls, shotcrete, precast concrete parts. Austrofaser is a ripple free polypropylene staple fiber and is manufactured according to ISO-NORM 9001 quality criteria in a melt spinning process. Austrofaser improves all relevant properties of concrete and mineral-bonded building materials. Consumption about 0.75 kg / m³ or about 0.90 kg / m³ Material: 100% polypropylene Fiber diameter: 7 dtex (32 μm) Fiber length: 12 mm Fiber section: round Color white

liquid roof and building sealant for indoor and outdoor use can be used vertically and horizontally ready to work can be applied to slightly damp substrates High quality, flexible, one-component, ready-to-use, water, solvent and silicone free, flexible and weather resistant for roofs and buildings, suitable for any indoor and outdoor sealing work and compatible with various types of surface materials such as natural stone carpets, ceramic coverings, mineral mortars, etc. Consumption Approx. 2.7 kg / m² for a 2 mm layer or in accordance with the requirements of the standard Color light gray / white

Permanently elastic, low solvent content, can be rolled Permanently elastic, low solvent, unfilled, bituminous coating with high resistance. Indoors and outdoors as a protective coating in biogas and sewage treatment plants, manure and slurry pits and in trays for collecting milk, fruit and fermentation acids. Consumption about 0.15 - 0.20 kg / m² per layer

high adhesion one component absorption-regulating Adhesion-strengthening, physically drying primer for polyurethane sealing compounds. It regulates the absorbency of the backing and provides a better adhesive bond to the edges of the seams and the sealing compound of the seams. Indoors and outdoors as an adhesive undercoat for absorbent and non-absorbent substrates before sealing with polyurethane and silicon seals. Consumption of 1 liter is sufficient for approximately 150 running meters (highly dependent on substrate) Substrate

bonding medium for standard metal substrates dries and degreases metals leaves a pale pink film behind one-component, ready-to-use can also be used as a cleaner Metal Primer MP Plus 2 is a ready-to-use special cleaning and bonding medium based on solvents for standard metal substrates, and is also used as a cleaner for instruments. Consumption approx. 0.1 l / m² as a cleaner for the special seal WD-1K approx. 0.1 l / m² as a binder Color pale pink

low solvent content acid-resistant permanently elastic Permanently elastic, low-solvent, unfilled, bituminous coating with high resistance to dilute acids (except oxidizing ones) and lizhy up to 2% concentration. Indoors and outdoors as a protective paint, for compacting foundations (min. 3 coats), as an undercoat for cold and hot bitumen coatings, for adhesion of films and cardboard. As a primer before bituminous compaction and scarfing works, for refreshing asphalt surfaces, as a sealant for cesspools and sludge pits, as well as a roof covering for weathered bitumen layers. Consumption Primer under the top coat: approx. 0.15 l / m² Primer under the sheathing: approx. 0.30 l / m² Insulating and protective paint, roof paint: approx. 0.25 l / m² (min. 2 coats) Fresh layer on asphalt: about 0.15 l / m²

chemical resistance permanently elastic good edge adhesion high resistance Highly elastic, odorless, permanently elastic, chemical resistant, one component, UV stable polyurethane based sealant with high edge adhesion. Indoors and outdoors as a universal sealant for expanding and joining joints in floors and walls. Especially for chemically stressed surfaces such as gas stations, commercial kitchens, swimming pools, industrial surfaces. Consumption about 1.2 kg per liter of articular space about 10 sq. m with a joint width of 5 mm

galvanized with mounting bracket or corner hinge waterproof easy and quick installation Galvanized steel tape covered on both sides with fabric-reinforced butyl rubber, also covered on both sides with tear-proof, easily removable silicon protective paper, separated in the middle. The butyl rubber coating reacts with the fresh cement paste component. For sealing joints in concrete structures. The flexible butyl rubber coating dissipates movements caused by concrete shrinkage.

solvent-free fiber-reinforced fracture bridge Two-component, solvent-free, fiber-reinforced, fractured bridge, plastically hardened bitumen coating. Two-piece sealing products, tested in accordance with EN 15814, consist of a fluid and a power component. Indoors and outdoors for the manual production of permanent, flexible seals for earth-contacting structures for use in horizontal and vertical applications. For adhesion of perimeter insulation panels on bituminous and mineral substrates in contact with the ground. Consumption Soil moisture approx. 4.5 kg / m² Unstable water = approx. 5.4 Wet layer thickness = approx 3.1 mm Dry layer thickness of standing water approx. 6.0 kg / m² = approx. 6.0 mm Wet layer thickness = approx. 4, 4 mm Dry layer thickness

filled with solvent-free polystyrene low material weight Two-component, filled with polystyrene, solvent-free, highly flexible, crack-like, plastically hardened bitumen coating. Indoors and outdoors for the manual production of permanent, flexible seals for earth-contacting structures for use in horizontal and vertical applications. For adhesion of perimeter insulation panels on bituminous and mineral substrates in contact with the ground. Consumption Adhesion of insulating panels: approx. 2 kg / m² Soil moisture / standing water: approx. 4.5 l / m² = approx. 4.5 mm Wet layer thickness = approx. 3.2 mm Dry layer thickness still water seepage: approx. 6.0 l / m² = about 6.0 mm Wet layer thickness = about 4.3 mm Dry layer thickness

ready to work fast reaction sprayable High quality, one-component polystyrene-filled, fast reaction plastic-hardened bitumen coating. Indoors and outdoors for the manual production of permanent, flexible gaskets for earth-contacting, earth-contacting structures. Consumption Adhesion of insulating panels: approx. 2.0 l / m² Soil moisture / non-standing water seepage: 3.5 - 4.0 l / m² (DIN 18195-4) Water unblown (horizontal): 3.5 - 4.0 l / m2 (DIN 18195-5) Standing seepage water: 4.5 - 5.0 l / m2 (DIN 18195-6)

suitable for drinking water containers whitewashed and spreadable on slightly damp substrates open to vapor diffusion Sulphate-resistant, plastic-hardened, mineral dry sealable sludge, especially for drinking water in accordance with the applicable test principles. Indoor and outdoor for horizontal and vertical sealing against non-pressurized water such as foundations, base plates, basement walls, retaining walls, potable and industrial water, gallery and tunnel construction, cisterns and underground car parks. As a masonry barrier under rising masonry, both as a negative filling and for the formation of cavities. Consumption with a spatula consistency of 2 - 3 kg / m² with a spreading consistency of 1.5 - 1.8 kg / m²

Moisture barrier (type A) Groundwater barrier (type T) Structural sealing membrane SK 100 is a cold adhesion bitumen membrane sealant with an HDPE carrier film. The product is tested in accordance with DIN 18195. The SK 100 structural seal is used for one-layer sealing of components in contact with the ground.

bitumen-free mineral crack bridge can be painted and plastered. Two-component, bitumen-free, solvent-free, very flexible, snappy sealing compounds for components, contact with the ground to protect against moisture. Indoors and outdoors for the manual production of permanent, flexible seals for earth-contacting structures for use in horizontal and vertical applications. Consumption depending on the case of loading: approx. 3 - 4 kg / m² per layer: approx. 1.5 - 2 kg / m² Color blue-green

Repeatedly washed, fire-dried quartz sand. For sanding primers, steam brakes and seals. For the production of filler etching and synthetic resin mortar. For filling epoxy and polyurethane resins and mineral fillers.

Pigmented mixture of polyester resin granulate and metal hydroxide. For filling with reactive resins for the production of creative, visually appealing design coatings. Light gray, anthracite

waterproof integration of shower trays and bathtubs Noise and cut protection high reliability of the filling system Two sets of sealing strips form a strong sealing system around the edges of the tub (tub or shower tray) to which the composite seal can be easily attached. The Basic WDB 35 bathtub sealing strip is used for connecting to towering walls, and the Basic HDB 36 horizontal bathtub sealing strip is used for horizontal bathtub to shelf transitions and edge joints of the bathtub to the floor.

thermal insulation versatile practical Thermal insulation, waterproof, fire-resistant, frost-resistant, vapor-dissipating, non-extinguishing carrier plate with high compressive strength made of extruded rigid polystyrene foam with textile glass mesh, reinforced with a special mortar coating. The Murexin Uni group is free of chlorofluorocarbons (CFCs), HCFCs or HFCs, and HBCD. For finishing facades and pedestals, as well as for special structures.

Ease of installation Continuously adjustable frame encloses the access points invisibly for the installation With the Uniflex stacking door, you get an invisible door to cover the access points after preparation. Thanks to the continuously adjustable plastic frame, Uniflex Classic tiles can cover door openings up to 45 x 45 cm. Without a frame, even cladding doors up to 60 x 60 cm are possible!

Cut protection for all sealing tapes self-adhesive alkali-resistant easy processing Self-adhesive cutting protection tape made of polyamide and aramid fabric. The tape is woven twice in the middle and thus provides the necessary cut protection or increases cut resistance. Cutting protective tape is a complement to sealing tapes for use in areas of silicone or sealing compound joints (walls, floor joints, bath or shower edges).

self-adhesive alkali-resistant Self-adhesive alkali-resistant reinforcing mesh. For reinforcing adhesive filler and lip seals. Used to absorb force, such as bridging cracks. ConsumptionCalculate overlap

glitter effect gold and silver for all RAL colors The glitter effect is created by mixing the glitter of a joint with an FMY 90 epoxy compound. As a sparkling showstopper or backlight to be able to set additional accents on the tiles. Consumption200 g / 6 kg of grout Color gold and silver

for indoor and outdoor use for walls and floors high flexibility, abrasion resistance and pearl effect for natural stone, fine porcelain stoneware and more for joints 1 to 6 mm wide (national specifications must be observed and observed) Powdered, food safe, water and frost resistant, super smooth, high strength and flexible pearl grout. Simple processing and further processing are possible without delay due to the simple application of filler in the joint and the same fast application, especially for non-absorbent material. In addition, the low water consumption of the highly abrasive grout reliably prevents staining. For grouting joints 1 to 6 mm wide for indoor and outdoor wall and floor surfaces. For water- and dirt-repellent grouting of ceramic tiles, boards, mosaics, as well as natural stone and fine porcelain stoneware. Suitable for underfloor heating systems in residential areas, as well as for wet rooms, terraces and balconies. Consumption 0.2 - 0.9 kg / m² (depending on tile format and joint width) Consumption calculator for Color gray, white, silver gray, Manhattan gray, cement gray, jasmine, bahama, silk gray, hazelnut, sand gray, camel , sanitary gray, walnut brown, bali, basalt, anthracite, black

permanently elastic very elastic membrane aging resistant hydrophobic Sealing collar, lined with fleece on both sides and with a very elastic expansion zone to absorb movement. In this way, pipes of different diameters can be sealed. Murexin sealed collars are waterproof and also chemically resistant to dilute acids, alkalis and saline solutions. System components for sealing water inlet / outlet in combination with sealing products or Murexin systems. Color is yellow

self-adhesive waterproof with fleece side Self-adhesive sealing tape made of butyl-coated polypropylene fleece with a split, overlapping silicone paper backing. Coated with highly elastic, self-adhesive butyl rubber. Component of a system for sealing walls and floors. For bridging and sealing joints and fillets.