Kharkov pumping plant

تقدم Trading House "Kharkiv Pump Plant" مجموعة كاملة من المواد الاستهلاكية عالية الجودة وقطع الغيار لمضخات الغطاس ND ، ومضخات الغشاء NDR-2M ، ومضخات ثلاثية الغطاس PT و T. نحن نقدم قطع الغيار: الديدان ، العلب ، المنزلقات ، والأصابع ، والحلقات ، والفواصل ، والبطانات وكذلك جميع أنواع السدادات والحشيات الخاصة بالجزء الهيدروليكي من المضخات. هناك أيضًا مجموعة واسعة من الأسطوانات الهيدروليكية للمضخات ومكونات الإصلاح الرئيسية. جميع أجزاء SPTA مصنوعة من مواد عالية الجودة في مصنع مضخة خاركيف. مهما كانت المضخة التي تستخدمها - جرعات الغشاء NDR-2M ، ومكبس الجرعات ND ، وثلاثة مكابس PT و T ، ستجد جميع قطع الغيار اللازمة لإبقائها في حالة صالحة للعمل. تضمن المعرفة والخبرة والمعدات الموثوقة إنتاجية عالية وتقليل وقت التوقف عن العمل.

Three-plunger crank pumps PT and T are designed for pumping neutral and aggressive liquids, neutral to the materials of the hydraulic part with a kinematic viscosity of no more than 800 mm2 / s (8 St) with a temperature, depending on the version, from 243 K to 473 K (from minus 30 to plus 200 ° С). The permissible content of solid non-abrasive particles in the pumped liquid is not more than 0.2% by mass, the permissible dimensions are not more than 0.2 mm. Three-plunger pumps of the PT and T type are used in industries requiring high pressures, including explosion and fire hazardous ones. Areas of use: ·                  oil production: drilling and well workover, circumferential waterflooding, enhanced oil recovery, oil dewaxing and well equipment. ·                  chemical and petrochemical industry: production of ammonia, urea, melamine, acetic, nitric and other acids, supply of reagents under high pressure; ·                  mechanical engineering: hydraulic cutting, hydroforming, power equipment for hydraulic presses. ·                  power engineering: feed pumps for boiler plants, steam generators. ·                  food industry: reverse osmosis plants, homogenizers. ·                  utilities: repair and pressure testing of pipelines and hydraulic systems, flushing of the sewage system. On the basis of pumping units, UN, UPG units are manufactured, which are designed for hydrotreating sewage and other pipelines with a diameter of 80 mm to 600 mm, as well as external and internal surfaces of various technological equipment, mechanisms, buildings, structures and other objects. Specifications: Supply - 1.25-3.2 m3 / hour; Pressure at the outlet of the pump-10 MPa Execution D1 Weight-355 kg Check the cost with the manager! Manufacturer's warranty - 1 year!

Pump membrane dosing units NDR-2M are designed for volumetric pressure head dosing of neutral and aggressive liquids, emulsions and suspensions. The area of ​​application of the membrane dosing unit is determined by the resistance of the materials of the flow path in the dosing medium and the design of the electrical equipment. Membrane pumping dosing unit NDR-2M can be used for dosing hazardous substances, flammable and combustible liquids, provided that safety rules are observed. To improve reliability, the diaphragm metering pump NDR-2M is equipped with a two-layer membrane made by & nbsp; from processed PTFE . 8 advantages of the NDR-2M membrane dosing pump: 1. Tightness. During operation of the NDR-2M pump, leakage of the pumped and working fluid is completely excluded. 2. Possibility of regulation without stopping the pump. & nbsp; The design of the NDR-2M pump provides pump running time. & nbsp; 3. Ease of operation and maintenance. & nbsp; In the pump NDR-2M & nbsp; no need to constantly monitor and maintain & nbsp; seal the plunger as it does with LP plunger pumps. & nbsp; 4. Wear-resistant valve. Diaphragm pump valves are specially designed for long-term operation in contact with aggressive media. Their service life is significantly longer than on conventional & nbsp; pumps ND. 5. The pump can operate at high pressures up to 100 MPa. Many diaphragm pump manufacturers cannot achieve this. 6. Membrane condition monitoring system. If the membrane is damaged, the control system will inform about it. Even in the event of a diaphragm rupture, the pump remains operational until the end of the process. Both a pressure gauge and electronic devices can serve as an alarm, which will report a problem to the control station. 7. Safety system In the event of blockage in the outlet piping due to faults or errors, a built-in valve will protect the pump from overload. & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp ; 8. Saving money Favorable price level achieved through our own production Technical characteristics of NDR-2M 400/63: & nbsp; Flow rate-400 l / h; Pressure at the pump outlet - 63 kgf / cm2; Engine-3 kW 1500 rpm; Order a diaphragm pump of European quality at a Ukrainian price!

Three-plunger crank pumps PT and T are intended for pumping neutral and aggressive liquids, neutral to the materials of the hydraulic part with a kinematic viscosity of no more than 800 mm2 / s (8 St) with a temperature, depending on the version, from 243 K to 473 K (from minus 30 to plus 200 ° С). The permissible content of solid non-abrasive particles in the pumped liquid is not more than 0.2% by mass, the permissible dimensions are not more than 0.2 mm. Three-plunger pumps of the PT and T type are used in industries requiring high pressures, including explosion and fire hazardous ones. Areas of use: ·                  oil production: drilling and workover of wells, circumferential waterflooding, enhanced oil recovery, oil dewaxing and well equipment. ·                  chemical and petrochemical industry: production of ammonia, carbamide, melamine, acetic, nitric and other acids, supply of reagents under high pressure; ·                  mechanical engineering: hydraulic cutting, hydroforming, power equipment for hydraulic presses. ·                  power engineering: feed pumps for boiler installations of steam generators. ·                  food industry: reverse osmosis plants, homogenizers. ·                  utilities: repair and pressure testing of pipelines and hydraulic systems, flushing of the sewage system. On the basis of pumping units, UN, UPG units are manufactured, which are designed for hydrotreating sewage and other pipelines with a diameter of 80 mm to 600 mm, as well as external and internal surfaces of various technological equipment, mechanisms, buildings, structures and other objects. Specifications: feed - 6.3 m3 / hour; Pump outlet pressure - 6.3 MPa Version D1 A1 - V-belt transmission Order pumping equipment from the Manufacturer with a 1 year quality guarantee!

Pump membrane dosing units NDR-2M are designed for volumetric pressure dosing of neutral and aggressive liquids, emulsions and suspensions. The scope of application of the membrane dosing unit is determined by the resistance of the materials of the flow path in the dosing medium and the design of the electrical equipment. The diaphragm pumping dosing unit NDR-2M can be used for dosing harmful substances, flammable and combustible liquids, provided that safety rules are observed. To increase reliability, the diaphragm metering pump NDR-2M is equipped with a two - layer membrane made   from treated PTFE . 8 advantages of the diaphragm dosing pump NDR-2M: 1. Tightness. During operation of the NDR-2M pump, leakage of the pumped and working fluid is completely excluded. 2. Possibility of regulation without stopping the pump.   The design of the NDR-2M pump provides for flow adjustment during pump operation.   3. Simplicity of operation and maintenance.   In the pump NDR-2M   there is no need to constantly monitor and maintain   plunger seal as is the case with LP plunger pumps. 4. Wear-resistant valve. The diaphragm pump valves are specially designed for long-term operation in contact with aggressive media. Their service life is much longer than that of conventional   pumps LP. 5. Ability to operate the pump at high pressures up to 100 MPa. Many diaphragm pump manufacturers cannot achieve this. 6. Membrane condition monitoring system. If the diaphragm is damaged, the monitoring system will report this. Even in the event of a diaphragm rupture, the pump remains operational until the end of the process. The signaling device can be both a pressure gauge and electronic devices that will report the problem to the control station. 7. Safety system In the event of a blockage in the outlet piping due to faults or errors, a built-in valve will protect the pump from overload.             8. Saving money Favorable price level achieved through our own production Technical characteristics of the diaphragm pump NDR-2M 40/400: Feed-40 l / hour The pressure at the outlet of the pump is 400 kgf / cm2; Electric motor power - 3 kW 1500 rpm. Factory warranty - 1 year!

ND plunger metering pumps are designed for volumetric pressure metering of neutral and aggressive liquids, emulsions and suspensions. The area of application of pumps is determined by the resistance of the material of which the hydraulic part is made, as well as the resistance of the seal material.   LP metering pumps are positive displacement pumps. By the form of movement of the working bodies - reciprocating.   Pumps of the ND series are single-plunger (double-plunger), horizontal, single-acting, with a manually adjustable flow when the electric motor is stopped. Flow rate-100 l / h The pressure at the outlet of the pump is 250 kgf / cm 2 Order European quality at Ukrainian prices!

The scope of application of the membrane dosing unit is determined by the resistance of the materials of the flow path in the dosing medium and the design of the electrical equipment. The diaphragm pumping dosing unit NDR-2M can be used for dosing harmful substances, flammable and combustible liquids, provided that safety rules are observed. To increase reliability, the diaphragm metering pump NDR-2M is equipped with a double - layer diaphragm made of treated PTFE . Advantages of the diaphragm dosing pump NDR-2M 1. Tightness. During operation of the NDR-2M pump, leakage of the pumped and working fluid is completely excluded. 2. Possibility of regulation without stopping the pump. The design of the NDR-2M pump provides for flow adjustment during pump operation. 3. Simplicity of operation and maintenance.   In the NDR-2M pump, there is no need to constantly monitor the plunger seal and maintain this seal, as is done when using ND plunger pumps. 4. Wear-resistant valve. The diaphragm pump valves are specially designed for long-term operation in contact with aggressive media. Their service life is significantly longer than that of conventional LP pumps. 5. Ability to operate the pump at high pressures up to 100 MPa. Many diaphragm pump manufacturers cannot achieve this. 6. Membrane condition monitoring system. If the diaphragm is damaged, the monitoring system will report this. Even in the event of a diaphragm rupture, the pump remains operational until the end of the process. The signaling device can be both a pressure gauge and electronic devices that will report the problem to the control station. 7. Safety system In the event of a blockage in the outlet piping due to faults or errors, a built-in valve will protect the pump from overload. 8. Saving money Favorable price level achieved through our own production Technical specifications: Feed - 1000 (l / h) The pressure at the pump outlet is 25 kgf / cm 2 European quality - Ukrainian price!          

Diaphragm dosing pumps NDR-2M were developed to replace the classic plunger pumps used in technological processes where leaks of the pumped medium are unacceptable. A distinctive feature and main advantage of diaphragm pumps is the complete tightness of the pumped liquid in relation to the environment. The seal in such a pump does not require maintenance during operation. Dosing diaphragm pumps of the NDR-2M series, manufactured at the Kharkov Pumping Plant, are designed for pumping liquids and suspensions, including toxic and aggressive ones. The presence of abrasive in the pumped liquid is not a problem for the diaphragm pump. The pumps are modular in design. Main units: drive, coupling, electric motor, hydraulic part. Supply - 6.9x10-6 (25) m3 / s (l / h); Pressure at the pump outlet, no more than - 40 (400) MPa (kgf / cm2) Electric motor power - 1.5 kW You can order equipment or its modernization, discuss the required configuration, get answers to your questions on request.

Three-plunger crank units and pumps ПТ and Т are designed for pumping neutral and aggressive liquids, neutral to the materials of the hydraulic part with a kinematic viscosity of no more than 800 mm2 / s (8 St) with a temperature, depending on the version, from 243 K to 473 K (from minus 30 to plus 200 ° С). The permissible content of solid non-abrasive particles in the pumped liquid is not more than 0.2% by mass, the permissible dimensions are not more than 0.2 mm. Pumps and units are used in industries requiring high pressures, including explosion and fire hazardous ones (for example, hydraulic cleaning of technological equipment). It is also used as feed pumps for mobile steam generating units. The three-plunger crank unit consists of an electric motor and a pump mounted on a common frame. The pumps can be driven by an electric motor, combustion engine or diesel engine. The connection between the pump and the electric motor can be carried out through a V-belt transmission, through a gearbox or directly through a clutch. The three-plunger pump consists of a drive and hydraulic parts. The drive end contains a crankshaft for converting the rotational motion of the engine into the reciprocating motion of the plungers. The hydraulic part consists of a valve body, plungers, stuffing box seals, suction and discharge valves, a safety valve. The safety valve is adjusted to the nominal working pressure, and if necessary, the valve can be adjusted to a different pressure. The units can be connected to devices that regulate the engine speed. Three-plunger crank units and pumps ПТ and Т are designed for pumping neutral and aggressive liquids, neutral to the materials of the hydraulic part with a kinematic viscosity of no more than 800 mm2 / s (8 St) with a temperature, depending on the version, from 243 K to 473 K (from minus 30 to plus 200 ° С). The permissible content of solid non-abrasive particles in the pumped liquid is not more than 0.2% by mass, the permissible dimensions are not more than 0.2 mm. Pumps and units are used in industries requiring high pressures, including explosion and fire hazardous ones (for example, hydraulic cleaning of technological equipment). It is also used as feed pumps for mobile steam generating units. Design The three-plunger crank unit consists of an electric motor and a pump mounted on a common frame. The pumps can be driven by an electric motor, combustion engine or diesel engine. The connection between the pump and the electric motor can be carried out through a V-belt transmission, through a gearbox or directly through a clutch. The three-plunger pump consists of a drive and hydraulic parts. The drive end contains a crankshaft for converting the rotational motion of the engine into the reciprocating motion of the plungers. The hydraulic part consists of a valve body, plungers, stuffing box seals, suction and discharge valves, a safety valve. The safety valve is adjusted to the nominal working pressure, and if necessary, the valve can be adjusted to a different pressure. The units can be connected to devices that regulate the engine speed. Delivery - 8 m3 / h Pump outlet pressure 16 MPa Weight-660kg European quality-Ukrainian price!

Three-plunger crank pumps PT and T are designed for pumping neutral and aggressive liquids, neutral to the materials of the hydraulic part with a kinematic viscosity of no more than 800 mm2 / s (8 St) with a temperature, depending on the version, from 243 K to 473 K (from minus 30 up to plus 200 ° C). The permissible content of solid non-abrasive particles in the pumped liquid is not more than 0.2% by mass, the permissible dimensions are not more than 0.2 mm. Pumps and units are used in industries requiring high pressures, including explosion and fire hazardous ones (for example, hydraulic cleaning of technological equipment). It is also used as feed pumps for mobile steam generating units. The three-plunger pump consists of a drive and hydraulic parts. The drive end contains a crankshaft for converting the rotational motion of the engine into the reciprocating motion of the plungers. The hydraulic part consists of a valve body, plungers, stuffing box seals, suction and discharge valves, a safety valve. The safety valve is adjusted to the nominal working pressure, and if necessary, the valve can be adjusted to a different pressure. The units can be connected to devices that regulate the engine speed. Flow rate - 4.0-10 m3 / h Pump outlet pressure 10 MPa 1 year manufacturer's warranty! Order European quality at Ukrainian prices!

Plunger metering pump units ND are intended for volumetric pressure metering of neutral and aggressive liquids, emulsions and suspensions with kinematic viscosity from 8.5 • 10-7 to 8.5 • 10-4 m2 / s (from 0.0085 to 8.5 cm2 / s), with a temperature from 258 to 473 K (from -15 to +200 ° C), with a solid non-abrasive phase concentration of not more than 10% by mass, with a maximum particle density of up to 2000 kg / m3, with a grain size of a solid non-abrasive phase no more than 1% of the nominal bore diameter of the inlet pipe. The area of application of the units (pumps) is determined by the resistance of the material from which the hydraulic part is made, as well as the resistance of the seal material. On the basis of metering pumps, the following installations are manufactured: one-component metering (UND) for metering supply to gas and oil field lines and objects of corrosion inhibitors, paraffin and scale deposits, demulsifiers and other products; multicomponent (up to 6 components at the same time) dosing (UMD) for simultaneous feeding into the technological line of a dosed amount of liquids or liquid mixtures, emulsions and suspensions with a temperature from 258 to 373 K (from -15 to +100 ° C). Multi-plunger units can provide the supply of liquids both separately by each cylinder and together in various combinations both at the inlet and outlet. Technical characteristics of the pump НД 25/400 К 14: Feed-25 l / hour; The pressure at the outlet of the pump is 400 kgf / cm2; Hydraulic part K - steel 12Х18 Н10 Т Order a Ukrainian pump ND from the KhNZ Trading House!

Plunger metering pumps ND are intended for volumetric pressure metering of neutral and aggressive liquids, emulsions and suspensions with a kinematic viscosity from 8.5 • 10-7 to 8.5 • 10-4 m2 / s (from 0.0085 to 8.5 cm2 / s), with a temperature from 258 to 473 K (from -15 to +200 ° C), with a concentration of a solid non-abrasive phase of not more than 10% by mass, with a maximum density of particles up to 2000 kg / m3, with a grain size of a solid non-abrasive phase not more than 1% of the nominal bore diameter of the inlet pipe. The area of application of the units (pumps) is determined by the resistance of the material from which the hydraulic part is made, as well as the resistance of the seal material. On the basis of metering pumps, the following installations are manufactured: one-component metering (UND) for metering supply to gas and oil field lines and objects of corrosion inhibitors, paraffin and scale deposits, demulsifiers and other products; multicomponent (up to 6 components at the same time) dosing (UMD) for simultaneous feeding into the technological line of a dosed amount of liquids or liquid mixtures, emulsions and suspensions with a temperature from 258 to 373 K (from -15 to +100 ° C). Multi-plunger units can provide the supply of liquids both separately by each cylinder and together in various combinations both at the inlet and outlet. Specifications: Feed-25 l / hour; Discharge pressure-250 kgf / cm2; Execution of the hydraulic part K - steel 12 X 18 H10T; Order time-tested quality!