All Pumps, compressors for oil & gas suppliers from Turkey

ALUMINUM BODY DIAPHRAGM PUMP PVDF BODY DIAPHRAGM PUMP PP BODY DIAPHRAGM PUMP Such pumps are used when pressure is required in chemical transfer. The body material and diaphragm of the pump are selected specially according to the usage area and the property of the liquid to be transferred. Since it works with air, it is suitable to work in flammable environments. Such pumps; They work with compressed air. The 2 diaphragms inside the pump are connected by a common shaft. Compressed air passes through the air distribution system, first pushing one diaphragm and then the other diaphragm with pressure. The diaphragm on one side is pressurized and pressurized, while the diaphragm on the other absorbs the fluid. When the compressed air changes direction and pushes the suction diaphragm, the fluid is discharged while the other diaphragm is sucked. Thus, while one side absorbs the liquid simultaneously, the other side presses the liquid. usage areas Air diaphragm pumps; used in fluid transfer, tank and barrel emptying, feeding and circulation processes BASIC FEATURES Dry suction Working without electricity Variable flow Fluid transfer containing particles Ex-proof feature Viscous fluid transfer

END SUCTION CENTRIFUGAL PUMPS Flow 1700m³ / h'ekad is Discharge head Up to 100m . The series is designed for printing non-corrosive liquids without large solid particles. . They are single-stage pumps and, thanks to the use of couplings in connection with the motor, offer the possibility to leave the motor or pump without displacement when necessary. . The overall dimensions of the snail comply with the TS EN 733 standard. . Suction and Delivery flanges comply with ISO 7005-2 / PN 16 standard. . Closed wheel is used in its series and balancing holes between the blades are balanced in dynamic loads in order to minimize axial loads. . Soft seal is used for shaft sealing. According to the demand, shaft sealing can also be provided with mechanical seal. . Thanks to its design, the wheel bearings and the packing can be easily replaced when necessary.

END SUCTION CENTRIFUGAL PUMPS Flow 1700m³ / h'ekad is Discharge head Up to 100m . The series is designed for printing non-corrosive liquids without large solid particles. . They are single-stage pumps and, thanks to the use of couplings in connection with the motor, offer the possibility to leave the motor or pump without displacement when necessary. . The overall dimensions of the snail comply with the TS EN 733 standard. . Suction and Delivery flanges comply with ISO 7005-2 / PN 16 standard. . Closed wheel is used in its series and balancing holes between the blades are balanced in dynamic loads in order to minimize axial loads. . Soft seal is used for shaft sealing. According to the demand, shaft sealing can also be provided with mechanical seal. . Thanks to its design, the wheel bearings and the packing can be easily replaced when necessary.

END SUCTION CENTRIFUGAL PUMPS Flow 1700m³ / h'ekad is Discharge head Up to 100m . The series is designed for printing non-corrosive liquids without large solid particles. . They are single-stage pumps and, thanks to the use of couplings in connection with the motor, offer the possibility to leave the motor or pump without displacement when necessary. . The overall dimensions of the snail comply with the TS EN 733 standard. . Suction and Delivery flanges comply with ISO 7005-2 / PN 16 standard. . Closed wheel is used in its series and balancing holes between the blades are balanced in dynamic loads in order to minimize axial loads. . Soft seal is used for shaft sealing. According to the demand, shaft sealing can also be provided with mechanical seal. . Thanks to its design, the wheel bearings and the packing can be easily replaced when necessary.

How Gear Pump Works? In Gear Pumps, two gears working together are mounted in a body. The gear connected to the drive shaft drives the idler gear. The vacuum formed by the movement of the gears working with each other at the small tolerances of the body carries the fluid into the pump. The fluid that fills into the gear cavities proceeds towards the pump outlet under the pressure created by the sliding rolling motion of the gears with each other. Gear pumps can operate in both directions. Transfered Liquids: Alkyd, Asphalt, Acids, Honey, Vegetable Oils, Bitumen, Paint, Glass Water, Chocolate, Detergent, Melted Rubber, Fuel-Oıl, Glucose, Glycerine, Gress, Animal Oils, Isocionate, Gel, Gelatin, Cocoa Yağo, Tar, Caustics , Cream, Mineral Oils, Printing Ink, Molasses, Diesel Oil, Naphtha, Paraffin, Petroleum Products, Poiol, Polyester, Resin, Soap Raw Material, Hot Oils, Solvents, Shampoo, Syrups, Sweeteners, Toluene, Glue, Varnish, Wax, Olive Oil . Gear Pump General Features: Flow rate: 0,5 - 200 m³ / h Pressure: 0 - 15 BAR Performance: With positive displacement, the pump pressure increases and the flow decreases slightly. The flow increases as the pump speed increases. NPSH: 0 - 6 meters Fluid: In all viscous fluids that do not contain hard particles Noise: Quiet with helical gear design. Power: Power increases with increasing Speed and Pressure. Discharge Line: By-pass is absolutely necessary in Discharge lines that may be closed. Temperature: Carbon Mattresses (-40 / 300 ° C) - Bronze Mattresses (-40 / 180 ° C) Viscosity: max. 100,000 SSU Sealing: Graphite, Teflon, Braided Seals - Mechanical Seal Production Types: By rusty - Without rust With steam jacket - Without steam jacket Bearing Plain Bed Outboard Bearing External Slip Bed All machinable metals Gear Pumps Installation and Commissioning Coupling adjustment should be checked. The suction pipe must be airtightly connected and the pump must be protected from dirt using a suitable filter. The suction line is 15 m. In fluids with a length exceeding 10000 SSU; suction pipe, pump, one or two pipe sizes should be larger. Compensator should be placed in suitable places to prevent additional load on the pump due to the installation. When braided graphite packing is used; seal pressure should be adjusted to flow 15-20 drops per minute. The suction circuit must be filled with fluid at the first start. During the first start of the pump; The pump shaft is turned by hand several times. Although they work in both directions, they work quietly in the OK direction. Pumps with By-Pas must be operated in the direction of OK. For this reason, the direction of rotation should be checked. Coupling adjustment should be checked The valves on the pipeline should be open. The pump is ready for operation if the above conditions are met.

Mono Pumps are pumps that provide a smooth, linear and measurable flow. These pumps operate silently and without vibration. Their most important feature is that they do not create turbulence by maintaining continuity. As a result, it does not change the viscosity of the fluid in mono pumps. Mono pumps are suitable for the transfer of low and high viscosity fluids as well as the transfer of abrasive, sticky, crushing and foaming sensitive fluids with their stabilization focused operating principles. It never breaks the fibers of the fluid inside and does not make any changes in the product structure. Mono Pumps generally protect the quality of products and systems by preventing foaming or excessive watering of solid or semi-solid fluids. With these advantageous features, Mono Pumps can transfer fluids smoothly in many sectors, even under the toughest application conditions.