Raw materials for industrial production in bulk on Qoovee

Aluminum sulfate is used as a coagulant for water purification for domestic and industrial purposes and is used in paper, textile, leather and other industries. Used as food additive E520. In the photograph it is included in the composition of stabilizing solutions and tanning fixers.

Hard gelatin capsules are filled with drug substance in a capsule filling machine. Designed for targeted transfer and release of drugs in the human body. Empty gelatin capsules are used for powdered or granular medicines.

It is made from oxides of aluminum and silicon, with the use of special additives to eliminate defects in the surface of the stone. It is necessary for giving a mirror shine to the surface at the stage of finishing polishing of granite, marble and other types of natural stone, as well as for artificial stones. Due to the shape and hardness of the aluminum oxide monograin, as well as the high dispersion of the powder, the polishing effect is achieved much faster compared to other types of similar products. Average powder consumption: 10-50g/m2 depending on the hardness of the polished material and its pre-treatment. To use, mix the required amount of powder with water to a paste-like mass and apply to the surface to be treated. Buff the paste with a felt nozzle to a final shine. The remains of the polishing material are washed off the treated surface.

Fine-dispersed aluminum hydroxide of various modifications, intended for wide use as a filler in the production of dry building mixtures, artificial stone, as well as a flame retardant filler in thermoplastics, thermoplastics and elastomers.

Crushed quartz sand is a raw material that is obtained by grinding natural quartz extracted from mountain deposits. Differs in purity and uniformity of structure, and also an uneven chipped form. After crushing, the material acquires such properties as high strength and abrasiveness. The composition of the raw material contains the maximum amount of silicon dioxide, as well as the minimum percentage presence of clay impurities. A large amount of silica and a minimum amount of impurities - all this determines the optimum resistance of the material to acids, as well as good refractory properties. Depending on the method of crushing and the subsequent appointment of the material, the grain size of crushed quartz can vary from 0.05 to 4 cm.

Fine-dispersed chalk MTD, MMS - crushed, natural, fraction 1 (2), CaCO3 or calcium carbonate. Content of calcium carbonate and magnesium carbonate: 98% Percentage of calcium: from 90% Insoluble residue in hydrochloric acid: up to 5% Harmless impurities (MgCO3, Fe2O3, Al2O3): up to 8% Moisture content in the composition: up to 6% Residue on a sieve with a diameter of 2 mm: up to 10% Due to the filling properties and low price, it is used by enterprises as a filler in such industries as: paint and varnish; polymeric; paper; glass; rubber technical; dry building mixes; feed and soil fertilizers; plastics and rubber.

triple pressed stearic acid. Acid value (mg KOH/g) 207-211 Color White Solubility in water Insoluble Saponification value (mg KOH/g) 208-212 Iodine value Max. 0.5 Density (g/cm3) 830±20 (℃) 54-57 C18 (%) 37-41 Shape Bead Application Production of glycerol esters, metal stearates, fatty amines, alkyd resins, lubricants, paper, plastics, coatings , paints, soaps, detergents, cosmetics, polishes, top coats and candles

Cotton wool for clothes and furniture. Specifications according to GOST 5679-91. bales of 25 kg, 50 kg, 80-100 kg. Cotton wool Lux, Cotton wool Prima, Cotton wool for sewing, cotton wool for mattresses

used for the production of polyethylene pipes and fittings for water supply, sewage pipes and pipes for gas supply

Our sulfur sales in Iraq and Iran have been going on for many years.

BioPro-V protein is a natural animal product, isolate of connective tissue beef protein. 100% bovine collagen fibers. It has a neutral taste and smell, the absence of gluten and genetically modified organisms. BioPro-V is a food raw material for food production and acts as a structure-forming ingredient. Beef protein is added during the production of meat products and is intended to create a protein framework. Both cold and heat-treated, it retains moisture and maintains emulsifying properties. Other benefits of BioPro-V protein • Helps to preserve the physico-chemical properties of frozen meat products - reduces moisture loss during defrosting and thermal processing; • When storing meat products, it reduces syneresis (release of excess moisture into the packaging of finished products) due to its fibrous structure. It has high water-binding capacity (WCC); • Unlike other proteins, BioPro-V has a high water holding capacity (WHR) throughout the entire heat treatment process. Has the ability to gel at temperatures of 70 degrees Celsius and above. Hot hydration increases gel stability. • High levels of WCC and WHC of protein reduce the secretion of meat juice and help to maintain stable properties of meat products during vacuuming; • BioPro-V is effective in maintaining the shape and stability of thin emulsion and traditional meat products with low protein content and weak structure formation; • High structure-forming properties of BioPro-V help to improve the formation and lagging of minced meat from the equipment in the production of semi-finished meat products; • The addition of natural protein to the recipe of meat products helps to significantly reduce the cost of production and improve the quality of the final product; • BioPro retains its functional properties in combination with other vegetable and animal proteins, fillers, carrageenans.

The high-quality additive is used as an additive in concrete and building mixtures, is a plasticizer and hardening retarder, leads to an increase in the strength of cement after 28 days. Sodium gluconate is used in industrial detergents: improves wetting, enhances cleaning properties, speeds up the rinsing process, prevents the formation of lime deposits and tartar. Sodium gluconate is used in metallurgy: in the production of steel and, especially in the production of aluminum, sodium gluconate works as an effective chelating agent that binds metal ions and thereby prevents deposits of aluminum hydroxide on surfaces, allows the precipitate to be easily removed during the filtration process.

Ascorbic acid E300 Ascorbic acid E300, vitamin C Ascorbic acid E300 or vitamin C is one of the main substances in the human diet necessary for the normal functioning of connective and bone tissue. Ascorbic acid is used in the food industry for the production of confectionery, jelly, marmalade, jams, canned fruits, vegetables, mushrooms, pasta, alcoholic drinks, liqueurs, wines, beer, soft drinks, juices, nectars, lemonade, dairy products, condensed milk, meat products, sausages, sausages, semi-finished products, fish products, bakery products, as well as the feed industry, the cosmetic industry, the pharmaceutical industry, the chemical industry. Used as an acidity regulator, antioxidant, preservative, baking powder, color stabilizer.

Noir Saint Laurent marble

Silver Onyx

Van Gogh Porcelain

BENTONITE (TehnoCLAI, TehnoCLAI HV), REAGENTS FOR REGULATION OF MUD PROPERTIES (TehnoGEL, TehnoPAC PR, TehnoFLOK) and AUXILIARY ADDITIVES TO IMPROVE DRILLING MUD PROPERTIES (TehnoSOAP, TehnoFREE, TehnoGREASE P). Products from Russian and foreign manufacturers with delivery to any city in the country.

Alinda Quartz

Boletus Quartz

Green Onyx

Savana Quartz

Lebedos Quartz

Coltan / Columbite-Tantalite Ore (Fe++Ta2O6) Columbite - (Fe) Formula: Fe2+Nb2O6 Color: Black to brownish black Luster: Vitreous, Sub-Metallic Hardness: 6 Specific Gravity: 5.2 - 6.65 Crystal System: Orthorhombic

Product Description: Specification Condensate cured silicone rubber for mold making, also called condensate curing silicone rubber and tin curing silicone rubber, is a commonly industrial room temperature vulcanized liquid silicone rubber (RTV-2). Areas of use. Condensate cured silicone rubber has a wide application, such as mold making of gypsum, gypsum, concrete, cement, flower pots, candles, soap, resin products, cultural stone, sculpture, GRC/GRG restoration, etc. Technical parameters Model code GTSIL-T10 GTSIL -T15 GTSIL-T20 GTSIL-T25 GTSIL-T30 GTSIL-T40 Hardness Shore A 8-10 14-16 19-21 24-26 28-32 38-40 Viscosity - cP 10000-14000 12000 -16000 14000-18000 16000- 20000 26000-32000 10000-14000 Mixing ratio - % 3% 3% 3% 3% 3% 3% Tensile strength - kN/m2 10-15 15-18 19-23 23-27 25-30 16-20 Tensile strength - MPa 3.5-5.5 3.5-5.5 4-6 4-6 5-7 3.5-5.5 Shrinkage, % 0.30% 0, 30% 0.30% 0.30% 0.30% 0.30% Elongation % 400-500% 400-500% 400-500% 400-500% 350-500% 350-500% How to use 1. Preparation substrates The surface of the original must be clean and free of loose material. If necessary, especially on porous substrates, use a suitable release agent such as petroleum jelly or soapy water.2. Mixing Thoroughly mix Component A (silicone base) before use, as separation of the filler may occur during prolonged storage. Weigh 100 g of Component A (silicone base) and 3 g of Component B (hardener) in a clean container. Stir until the hardener is completely dissolved in the base. Manual or mechanical agitation may be used, but do not agitate for long periods of time and do not allow temperature to rise above 35°C (95°F). Mix suitable small amounts to ensure that component A (silicone base) and component B (curing agent) are thoroughly mixed. It is highly recommended to remove entrapped air in a vacuum chamber, allowing the mixture to fully expand and then collapse. After another 1-2 minutes under vacuum, the mixture should be checked and can be used if there are no air bubbles in it. Vacuum deaeration of the mixture results in an increase in volume by 3-5 times, so a sufficiently large container should be chosen. Note. In the absence of vacuum deaeration equipment, air entrainment can be minimized by mixing a small amount of component A (silicone base) and component B (hardener) and then applying a 1-2 mm layer to the original with a brush. Leave at room temperature until bubbles disappear from the surface and the layer starts to harden. Mix additional base and hardener and follow the steps below to make the final shape.3. Pouring the mixture and curing Pour the mixture of Par A (silicone base) and Part B (hardener) as soon as possible onto the original, avoiding air entrapment. The catalyzed material cures to a flexible rubber within 24 hours at room temperature (22-24°C/71.6-75.2°F), after which the mold can be separated from the original. If the operating temperature is much lower, the curing time will be longer. If the room temperature or humidity is very high, the run time of the catalyzed mixture will be shortened. The final mechanical properties of the mold are achieved within 7 days.

Product Description: The specification of mold additive cured silicone rubber, which also uses additive treatment silicone rubber and platinum curing silicone rubber, is usually a two-component liquid silicone rubber, stress vulcanized (RTV-2). Applications: Additive cured silicone rubber has a wide application, such as food mold making (candy, cake, biscuit, chocolate, ice cubes, fondant, etc. foaming, making breast prostheses, artificial leather, human body, Model Code GTSIL-P10 GTSIL-P15 GTSIL-P20 GTSIL-P25 GTSIL-P30 GTSIL-P35 GTSIL-P40 Shore A 8-10 14-16 19-21 24-26 28-30 34-36 38-42 Viscosity - SP 3000-5000 4000-6000 4000-7000 5000-8000 6000-9000 6000-10000 4000-6000 1:1 1:1 1:1 1:1 1:1 1:1 - MPa 3.5-5, 5 4-6 4-6 4-6 4-6 4-6 3.5-5.5 Shrinkage - % 0.10% 0.10% 0.10% 0.10% 0.10% 0.10% 0.10%. Elongation - % 500-600% 500-600% 500-600% 400-500% 400-500% 350-500% 300-450%. free of loose material If necessary, especially on porous substrates, use a suitable release agent such as petroleum jelly or soap solution. nent A (silicone base) before use, since the filler can quickly exfoliate during long-term storage. Weigh 100 g of Component A (silicone base) and 3 g of Component B (hardener) in a clean container. Stir until the hardener is completely dissolved in the base. You can use manual or mechanical change, but do not change for an extended period of time and do not allow the temperature to rise above 35°C (95°F). With frequent falling under a small amount, which are exceptional characteristics of component A (silicone base) and component B (hardener). It is highly recommended to remove the air entrapment in the vacuum tank, the intake of the mixture is fully expanded and then collapsed. After another 1-2 minutes in a vacuum, you can check the mixture if there are no air bubbles in it. Vacuum deaeration of the mixture results in an increase in volume by 3-5 times, so a sufficiently large container should be chosen. Note. In the absence of vacuum deaeration equipment, air entrainment can be minimized by mixing a small amount of component A (silicone base) and component B (hardener), and using a brush to accurately determine 1-2 mm of layer on the original. Leave the temperature until the bubbles disappear on the surface and the layer slows down. With the addition of additional bases and hardener and the possibility of implementation for the final form. 3. Filling the mixture and curing. Pour the mixture of Par A (silicone base) and Part B (hardener) as soon as possible onto the original, avoiding air trapping. The catalyzed material cures to a flexible rubber within 24 hours at ambient temperature (22-24°C/71.6-75.2°F), after which the mold can be separated from the original. If the operating temperature is much lower, the curing time will be longer. If the room temperature or humidity is very high, the run time of the catalyzed mixture will be shortened. The final mechanical properties of the mold are achieved within 7 days.

Copper Cathode Pure 99.99% Factory Price Cathode Copper/ 99.99% Pure Copper CathodeitemvalueWeight.125kgsGradecopperCu (Min)99.99Place of Origin..ChinaBrand NameOEMModel Numbercopper cathodeProcessing ServiceBending, Decoiling, Welding

High Purity Aluminum UBC/Aluminum Scrap   High Purity Aluminum UBC/Aluminum ScrapDetailsPlace of Origin:UK.Brand Name:zhongling...Model Number:zhongling-aluminum ubc scrap-1Type:Aluminum Can.Weight:50kgAl Content (%):99.7Aluminum scrap:Pure 99.9% Aluminum Ubc Scrap Aluminum ScrapMaterial:Alloy 6063Color:Multi ColorGrade:Top GradeQuality:ExcellentApplication:Recycling MaterialDelivery Time:7-15dayPackage:CompressedMOQ:50 MTitemvaluePlace of OriginUKBrand Nameubc scrapModel Numberzhongling-aluminum ubc scrap-1TypeAluminum CanWeight50kgAl Content (%)99.7Aluminum scrapPure 99.9% Aluminum Ubc Scrap Aluminum ScrapMaterialAlloy 6063ColorMulti ColorGradeTop GradeQualityExcellentApplicationRecycling MaterialDelivery Time15-20dayPackageCompressedMOQ50 MTAluminum UBC ScrapAvailability

PET Bottle Scrap/PET FlakesPlace of Origin:United Kingdom.Brand Name:PET BottlesModel Number:ISO 9001.Product Name:PET Plastic Bottles ScrapColor:Clear, White, Mixed Color.Material:Polyurethane..Grade:100% Clean, 100% Clear PET BottlesSource:Water Bottles, Juice BottlesColor ratio:Clear 100%PET Bottles:100% Transparent clear, 100% blue, 100% green balesPVC:Less than 0.01%Water Content:Less than 0.01% moistureImpurity:No Caps, rings, or labelsPackaging DetailsIn Bales 50X50X80 cm at 80 Kg/Bale. Flakes washed or unwashed in 50 Kg used PP bags, 25 Mt. in each 40' HQ ContaineritemvaluePlace of OriginUnited KingdomBrand NamePET BottlesModel NumberISO 9001Product NamePET Plastic Bottles ScrapColorClear, White, Mixed ColorMaterialPolyurethaneGrade100% Clean, 100% Clear PET BottlesSourceWater Bottles, Juice BottlesColor ratioClear 100%PET Bottles100% Transparent clear, 100% blue, 100% green balesPVCLess than 0.01%Water ContentLess than 0.01% moistureImpurityNo Caps, rings, or labels

Aluminum Scrap/ 100% Clean Aluminum Sheet Scrap, UCB ,Aluminum Wire, Aluminum Scrap 6063 On SaleitemvaluePlace of OriginChinaBrand NameHBZKModel Number.97%TypeAluminum WheelWeightdifferent style different weightAl Content (%)97%Delivery Time5-7 DaysPurity99.97% MinDensity2.702g/cm³GradeTop GradeMOQ10 TonsPackingStandard PackagingBoiling point2467.0℃Melting point660.37℃.style14 inch/ 15inch / 17inch / 18inch /.

Yellow color. Load capacity < 100 kg. Blocking: Without brake. Purpose: Furniture, trolley. Wheel material PU. Wheel movement: Rigid. Wheel size (inch) 2X0.5.

Black masterbatches. Contains soot for black coloration. The soot content can reach up to 46%. The higher the soot content in the masterbatch, the less should be added. White dye concentrates. They contain a white pigment - titanium dioxide, which provides the best staining in white. The best recommended titanium dioxide from the world's leading manufacturers: DuPont, Hansmann Kronos, Cristal. Color masterbatches. These masterbatches contain a dispersed mixture of color pigments in a polymer. Are applied to all types of color coloring of films and plastic products. Masterbatches of additives contain in their composition a variety of additives that give the polymer the necessary additional properties (UV stabilizers, sliding additives, etc.)

Our Kiwi seeds is not for growing, it is for food processing, such as oil extracting for pharmaceutical, health and care industry. Welcome contact us for more details.

ERMAMAT-QUARTZ LLC, operating under a license of the NV series number 0256 F5 dated 07/08/2020 for the extraction of crushed quartz. Crushed quartz sand is a raw material that is obtained by grinding natural quartz extracted from mountain deposits. Differs in purity and uniformity of structure, and also an uneven chipped form. After crushing, the material acquires such properties as high strength and abrasiveness. The composition of the raw material contains the maximum amount of silicon dioxide, as well as the minimum percentage presence of clay impurities. A large amount of silica and a minimum amount of impurities - all this determines the optimum resistance of the material to acids, as well as good refractory properties. Depending on the method of crushing and the subsequent purpose of the material, the grain size of crushed quartz can vary from 0.05 to 4 cm. APPLICATIONS OF QUARTZ SAND The use of quartz sand is practically unlimited. It is resistant to chemical, mechanical and atmospheric influences, and also has good fluidity. This material is used at: - production of dressing for roofing material; - decorative plaster; - production of refractory products; - steel production; - sprinkling of sports grounds and personal plots; - making molds for the foundry industry; - removal of metal corrosion; - production of enamels, varnishes and paints; - formation of a covering of floors of working rooms; - filtration of drinking water and industrial wastewater; - production of fine-grained concrete and polymer concrete; - manufacture of glass and fiberglass. LLC "ERMAMAT-QUARTZ" offers you its products according to the following characteristics: Crushed vein quartz of milky white color, Sio2 content of more than 99.5% corresponds to GOST 22551-77 grade VS - 050-2. Ready to use, cleaned, dried and packed in a 25kg bag. and 1000 tons.

Our company has the ability to supply petroleum coke, grade 3. All documentation is attached. We will consider applications mainly to China and Uzbekistan.

Orthophosphoric acid, food grade, 85% Packing: 1) 35 kg canister - net weight, gross weight - 36.5 (760 canisters = 26.6MT net weight without pallet, gross weight - 27.74MT) fit in a 20GP container. ON PALLET number of 35 kg canisters: 736 = 25.76mt net weight. 2) there is also 1000l euro cubes, net weight - 1320 kg 26.4MT net weight can fit in a 20GP container Readiness of cargo: 15-20 days after payment. Delivery through Russia: port of Vladivostok or Vostochny. ITEM IS IN CHINA!

Good day! Selected good seeds for sunflower oil and more. Write to find out the price and availability of goods.

Forming fabric include: Single layer forming wire, Double layer forming wire, 2.5 layer forming wire, SSB forming fabric, Cresent Former Forming Fabric With many years of experience in production single layer forming fabric, Huatao can supply a wide range of single layer forming fabric. single layer forming fabric can meet many applications, if you need, please get our online timely service about single layer forming fabric. In addition to the product list below, you can also customize your own unique single layer forming fabric according to your specific needs. The 4-Shaft design single layer forming fabric commonly used in manufacturing all varities of paper grades. Four Shed Design Mesh available from 16/cm to 30/cm. Can be supplied in various combinations of warp (MD) yarns and welt (CD) yarn diameters. Specially suitable for writing printing papers where empahsis is on the formation of paper and also in coarseness. It is widely used in Liner Board, Pulp Board etc. The 5-Shed design single layer forming fabric available from 22/cm to 30/cm Can be supplied in various combinations of warp (MD) yarns and weft (CD) yarns diameters Suitable for all type of paper grades where emphasis is on life of forming fabrics. Can be Supplied warp(MD) runner for tissue machines.

We have Variety of Cotton with Various Staple Length, Micronaire, and Strength. Ellipsis International exports and supplies all the types of Indian raw cotton from various cotton growing Indian States - mainly Shankar 6 cotton .In India different types of cotton species available, i.e. short staple 20 mm & below , medium staple (20.5 to 24.5mm), Medium long (25.0 to 27.0mm), Long (27.5 to 32.0 mm) and extra long staple cotton (32.5mm and above). We Have 2 Qualityies of Grades : 1) Premium - Grade 1 2) Standard - Grade 2 Additional Information: Item Code: L1 Production Capacity: 10000 Metric Tons Delivery Time: 7-10 Days Packaging Details: 170 Kgs/ Bale with Cloth and String Packaging & Can be Custummized as Per Clients Requirement.  

Caluanie Muelear Oxidize is used for crushing and processing precious metals and semi-precious stones. It is used for processing precious and semi-precious stones, crushing metals in the chemical industry. The chemical product Caluanie is a light brown viscous liquid obtained from the transesterification of a raw palm solution. Raw Caluanie 100% is produced in Muelear's Oxidation & Pasteurization Plant and is an outstanding chemical with the potential to be used worldwide primarily in the chemical centralized manufacturing industry. MAIN USE: Caluanie is widely used in chemistry, paint industry as a substitute for hygroscopic agent. It is widely applied in coatings, paints, plastics and printing ink industries. Caluanie Muelear Oxidize Purity We offer high quality Caluanie Muelear Oxidize Purity for sale Caluanie Muelear Oxidize (Caluanie Raw Water is 99% Muelear oxidize), Caluanie (Oxidative Partarisation Thermostat, Heavy Water). PACKAGING: Available packaging: 1 l - 5 l and bulk packaging from 20 l, 50 l, 100 l. at the request of the buyer. Caluanie is available for laboratory use. We can supply Caluanie Muelear Oxidize for individual scientists and scientific institutions specializing in heavy water and oxidizers. In doing so, we aim to facilitate the research of laboratory-tested substances. HANDLING SAFELY WITH CALUANIE MUELEAR OXIDIZE Caluanie is a hazardous product that can cause acute toxicity if used incorrectly. For industrial applications, staff training is essential to minimize health risks. Make sure that everyone who will be working with this substance is aware of the general chemical safety rules for proper handling and storage. As the manufacturer of Caluanie Muelear Oxidize, we take our responsibility to raise awareness of the safe use of this substance seriously. The pictogram on the label means that you need to be very careful when handling Caluanie. Always use personal protective equipment to prevent skin contact or ingestion. To prevent a fire hazard, never smoke while handling the chemical. HOW TO TEST CALUANIE A metal rod with a diameter of 6 mm is immersed in this liquid for 3-5 minutes. The rod or nail is then removed from the liquid and becomes very brittle and easy to break with bare hands.

Payment terms and dilivery discuss with client P2P