Product description
Repair mixture
for concrete
ICBM 500
Appointment :
Dry construction mix MBR 500 is intended for the preparation of building fine-grained concrete (mortar) used for repairing concrete structures, monoling joints, technological holes, sealing cracks in concrete, brick walls, ceilings, etc.
Composition :
Dry construction mix MBR 500 is a polymer-mineral fine-grained mixture obtained by intensive mixing of fractionated sand, Portland cement and a complex of modifying additives.
Concrete preparation :
For the preparation of dry building mix MBR 500 pour into clean fresh water, constantly mixing until a homogeneous mass is obtained using an electric drill with a mixer nozzle or a low-speed forced-action mixer.
The amount of water required for the preparation of concrete is determined from the ratio of 0.18-0.19 l per 1 kg of dry construction mixture. Excess water contributes to the formation of cracks.
Ready concrete must be used within 15 minutes.
Preparation of the working surface (base) :
The working surface (base) must be strong, durable, free of dust, dirt, oils, fats, wax, bitumen, paint residues, cement milk, efflorescence. Cracks are broken, old fragile concrete is removed, the released reinforcement is cleaned of rust. The prepared surface is cleaned of dust with compressed air, washed with water or treated with a sandblasting machine. It is necessary to treat with a polymer-mineral primer weak and highly absorbent substrates. Metal parts must be treated with an anti-corrosion solution.
Concrete Application :
Before applying concrete, the prepared surface is abundantly moistened. The water is allowed to soak and then manually apply concrete with a spatula. It is necessary to reinforce the applied repair layer with large areas of the surface to be repaired, repair of places subject to large bending loads, and a concrete layer thickness of more than 50 mm.
Concrete laying is carried out without interruption until complete completion, or by grips. Before applying subsequent layers, it is necessary to moisten the previous layer, i.e. observe the processing method - “wet on wet”.
The temperature of the working surface should be at least + 5ºС and not more than 30ºС. At negative temperatures up to -10ºС, the repair mixture MBR500M is used. To prepare the solution, it is necessary to use water at a temperature of at least 15 ° C. Stir the solution until the antifreeze additive is completely dissolved for at least 5 minutes from the moment of adding water.
The consumption of dry mix depends on the type of repair. To repair a damaged horizontal surface with a repair layer thickness of 50 mm, 95-110 kg of mixture per 1 sq.m. To close a hole in a concrete wall with a diameter of 30-35 mm and a depth of 10 cm, 150-200 g of mixture is required, to close a crack with a width of 20 mm and a length of 1 m at a depth of 20 mm, 700-750 g of mixture are required.
Specifications :
Astringent
Portland cement
Aggregate
fractionated sand
Placeholder fraction
up to 1.0 mm
Water retention capacity
not less than 9 5 %
Maximum thickness in one run
50 mm
Water consumption for cooking
0.18-0.19 L per 1 kg of mixture
Viability
not less than 60 min
Work surface temperature
For MBR-500
For MBR-500M
from + 5˚С to + 30˚С
from -10˚С to + 5˚С
Compression strength after 28 days (grade)
500 kgf / m 2 (50 MPa)
Peel strength from concrete surface
17.5 kgf / m 2 (1.75 MPa)
Frost resistance
no less than 400 cycles
Water resistant
not less than W 10
Safety precautions :
Portland cement contained in the mixture, when interacting with water, forms an alkali. Avoid getting ready-made mortar on the skin and mucous membranes. In case of contact, rinse the contact area with clean running water.
Strength chart of ICBM 500M (seven-day strength calculation)
No.
p / p
Hardening temperature, ° С
The strength in the samples is 70.7x70.7x70.7 mm when hardening for
1 day
3 days
7 days
14 days
28 days
1
twenty
15.8
22.4
32,7
40.5
51.0
2
-5
3.3
10.0
18.1
20.8
28.5
3
-10
2,4
8.1
14.5
17.8
26.9
The set of strength can vary within the permissible variation of 15%.
Shelf life :
Store mortar in a dry place at a relative humidity of 60%, temperature from –50 to +50 ˚С. Shelf life in the manufacturer’s packaging 6 months from the date of manufacture
Learn more
Check availability
7.63
USD/pcs
7.63
USD
Minimum order: 1 pcs
Supply ability: 1 pcs/per day
ООО Наш Двор-РСК
Not verified supplier
Russia
Shipping information
Calculate and complete your cargo transportation worldwide using Qoovee Logistics.
Guaranteed shipment on time and secure payment Calculate shipping from QooveeSimilar products
DINIL PLUS
Uzbekistan
USD
0.6/pcs
0.6
Plastic ventilation grill - round perfect for covering holes in the wall, in the ceiling or for closing the ventilation duct Made of high quality ABS material. Environmentally friendly, durable. For connection to 125 mm round ducts, mounting with a mounting flange
DINIL PLUS
Uzbekistan
USD
0.8/pcs
0.8
Plastic revision hatch 200x300 mm Plastic revision hatch door with handle. For access to hidden units and utilities. Designed for wall or ceiling installation. Equipped with a handle for easy opening / closing of the hatch. Can be used in wet rooms. Easy maintenance. Installation is carried out using mortar or glue.
ZLATAR
Kazakhstan
USD
16.35 - 54.49/pcs
Stainless steel air conditioning grilles both in a finished design and for an individual order.
Best Choice Ukraine
Киев, Ukraine
USD
6.32/pcs
6.32
Garden path mold Round Stones 80x80x6 cm
Garden paths create a chic view of the suburban area, which add tidiness and nobility.
Concrete paths are durable and very practical. They are not afraid of any atmospheric conditions and are easy to clean.
At the present time, it is possible to make a concrete path with your own hands using special forms. Such a path will not only create comfort and coziness, but also emphasize the design of your site.
Drawing - an imitation of natural stone will help to create a mold for making a garden path. Round Stones 80x80x6 cm. This plastic mold consists of 9 cells that have an arbitrary shape and are connected together. They form a certain pattern, while the shape is designed in such a way that it allows the slabs to be joined together in any direction, to obtain tracks of the required width, as well as to make turns (bends), while the joints are absolutely indistinguishable.
It is also possible to adjust the color scheme of the garden path using various additives. With this form, you can easily decorate the paths in the garden or playground and you will be satisfied with the work done with your own hands.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the shape for the garden path Round stones:
Manufacturer: Hormusend
Country of origin: Ukraine
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 1.56 pcs
Pattern: round stones
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Number of stones in the form: 9 pcs
Finished board height: 60.0 mm
Finished stone height: 60.0 mm
Volume: 40 l
Length: 800.0 mm
Width: 800.0 mm
Height: 60.0 mm
Weight: 1.6kg
Volume weight: 9.6 kg
Best Choice Ukraine
Киев, Ukraine
USD
4.5/pcs
4.5
Garden path mold Castle Stone 60x60x6 cm
It has become easier to create comfort and coziness in the garden. You can make an unusual geometric design, similar to a composition from a natural stone, without a lot of time. You don't need to match each item individually. Simply pour the solution into the garden mold. From the resulting slabs, you can easily create a decorated walkway.
The garden path mold will serve you for a long time, as it is made of wear-resistant polypropylene. You can always use it to create an additional pedestrian zone in the garden.
The walkway will emphasize the design of your site, as the pattern is similar to a natural stone composition.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the mold for the garden path Castle Stone:
Manufacturer: Hormusend
Country of origin: Ukraine
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Pattern: imitation of a wild stone
Number of stones in the form: 9 pcs
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 2.78 pcs
Finished board height: 20.0 mm
Finished stone height: 40.0 mm
Length: 600.0 mm
Width: 600.0 mm
Height: 60.0 mm
Weight: 1.7kg
Best Choice Ukraine
Киев, Ukraine
USD
5.54/pcs
5.54
Garden path mold Castle Stone 60x60x6 cm with handles
An integral element of a well-groomed garden is a garden path, which allows you to comfortably move through it and not worry about the ground sticking to your shoes.
With minimal knowledge of construction and little effort, it is easier to pour a concrete path than to lay tiles. To make it as quickly and easily as possible, use a unique modern development - a special stencil that looks like cells that realistically imitate natural stones.
An unusual geometric design will allow you to make an easy-to-use shape for a garden path Castle Stone 60x60x6 cm with handles.
The garden path mold is made of wear-resistant polypropylene and is equipped with 2 handles for convenience. You just need to pour the solution into it, and after partial hardening, the form can be removed. Provided manufacturer's warranty for up to 1000 pouring cycles.
For a unique design, it is recommended to add a color pigment directly to the solution.
Benefits of using a garden path mold:
Quickness of manufacture - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the mold for the garden path Castle Stone:
Manufacturer: Hormusend
Country of origin: Ukraine
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Pattern: imitation of a wild stone
Number of stones in the form: 9 pcs
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 2.78 pcs
Finished board height: 20.0 mm
Finished stone height: 40.0 mm
Length: 600.0 mm
Width: 600.0 mm
Height: 60.0 mm
Weight: 1.7kg
Best Choice Ukraine
Киев, Ukraine
USD
3.68/pcs
3.68
Form for a garden path Old Town 60x40x6 cm
A garden path on the site not only creates a beautiful view and comfort, but also is an excellent protection for your shoes from the ground, dirt and dust.
Thanks to modern technologies, it is possible to make the coating independently, which gives complete confidence in its quality.
Plastic mold Old City 60x40x6 cm for laying a concrete path will help you to model and lay your garden path or playground in the shortest possible time.
It is reusable, made of durable material - polypropylene. On the slab there are 9 decorative stones 11x18cm, the seam depth is 2 cm. The wall thickness is 4 mm, the edging of the stone is 2 mm. In places of loading, stiffeners are implemented, which allows it to withstand 1000 moldings.
To use it, it is enough to prepare a concrete solution. The shape fits well on either side, allowing you to make the track seamless.
If we compare the total costs, then a do-it-yourself garden path made of concrete, obtained using a form, will cost less than laying tiles or pebbles.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the form for the garden path Old Town:
Manufacturer: Hormusend
Country of origin: Ukraine
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 4.17 pcs
Pattern: Old Town
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Number of stones in the form: 9 pcs
Finished board height: 60 mm
Finished stone height: 60 mm
Length: 600.0 mm
Width: 400.0 mm
Height: 60.0 mm
Best Choice Ukraine
Киев, Ukraine
USD
3.68/pcs
3.68
Garden path mold Universal Stone 60x40x6 cm
A beautiful view of the countryside provides a decor that should be combined with the rest of the garden. Its main element is a practical and unique garden path or playground, which can be easily modeled and created with your own hands using plastic molds and a concrete grout.
An excellent solution for a plot that is decorated in a strict, classical or modern style would be the use of an unusual shape for the garden path Universal Stone 60x40x6 cm, the design of which is designed for convenient work with concrete.
It is a sturdy and secure shape with strong edges. Its feature is the presence of technological holes for handles, which is convenient when pouring large areas. During the first molding, special cavities in the inner seam are filled with mortar, which gives the form additional strength.
The drawing of the shape is two large and two small triangles. The outer frame is made in such a way that it can be easily docked even with molds from other manufacturers.
For the uniqueness of the design, it is possible to adjust the color scheme of the garden path with the help of various additives.
By making your own coating, you will be sure not only of its quality, but also of budget savings.
Benefits of using a garden path mold:
Fast production - the solution is ready within 20-30 minutes;
Individual creation of a picture - the ability to add color pigments for the uniqueness of the board;
Saving the budget - only the purchase of materials;
Ease of use - does not require special knowledge and skills, enough imagination and familiarization with training materials.
Characteristics of the form for the garden path Universal Stone:
Manufacturer: Hormusend
Country of origin: Ukraine
Guaranteed number of pouring cycles: 1000
Number of molds per 1m2: 4.17 pcs
Pattern: universal stone
Type: garden path mold
Material: wear-resistant plastic (polypropylene)
Number of stones in the form: 4 pieces
Finished board height: 60 mm
Finished stone height: 60 mm
Length: 600.0 mm
Width: 400.0 mm
Height: 60.0 mm
Weight: 1.0KG
Suppliers in this category
All suppliers in the category
Product:
Supplier:
Min. order:
Directory
Marketing department:
Marketing department:
Marketing department:
Information
Inform manager that you found the product on Qoovee
The contact details of the supplier is not available!
Send message