Vehicles & parts in bulk on Qoovee
Sort by:
Oil-Grupp
Санкт-Петербург, Russia
USD
262.63 - 1541.52/pcs
Коммерческое предложение по авто маслам оплата нал/без нал доставка за наш счёт доставка от 1 до 3х дней насосы в подарок
ИП Шмельков А.А
Russia
USD
13.99/pcs
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
It is intended for obtaining solder rods by the method of continuous pulling upward of casting billets from copper melt and cutting them into dimensional cuttings. Consists of: pulling stand of two-roll type, operating in step-by-step mode from one drive with the possibility of individual pressing of each workpiece at two points; molds mounting brackets; carts for manually moving metal receivers; devices for cutting bars into measured lengths; common installation frame; machine control system, including cabinet and control panel. Smelting furnaces are not included in the scope of delivery.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for punching grooves and holes, punching perforation corners in metal sheets. It is possible to use combined dies for simultaneous punching of grooves and holes. Can be completed with a feeder, table, roller conveyor. To operate the presses, a compressed air line under a pressure of 0.7 MPa is required. Control from a pedal or according to a technical assignment from two buttons simultaneously. The presses can work autonomously or as part of a line.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for simultaneous punching of 4-corner segments in the shelves of a U-shaped profile, punching a tongue and punching holes for further connection of the ends of the profile into a frame. They consist of: a rigid frame on which the press blocks with stamps are mounted, an additional movement mechanism, a device for removing cut profiles, hydraulic equipment, which includes a hydraulic station, an electrical cabinet with a control panel. The blank of the U-shaped profile is installed manually on the dies and positioned along the stops. After performing all operations, the profile is automatically removed from the installation.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for firing ceramics and other materials. They consist of a bed, a casing, a heating chamber, lining with refractory and heat-insulating materials, an electrical cabinet. Control from a stand-alone console. Heating of the furnace is electric. The heating chamber has three heaters: two heaters at the sides and one heater at the bottom of the furnace. Coil heaters are attached to ceramic tubes. Heater material - fechral Ø 4 mm.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for firing ceramics and other materials. It consists of a bed, a casing, a heating chamber, lining with refractory and heat-insulating materials, an electrical cabinet. Control from a separate control panel equipped with a microprocessor-based temperature control system in the furnace. At the request of the Customer, the furnace can be equipped with an electromechanical drive for the bogie hearth.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for firing powder materials. They consist of a lined heating chamber, inside of which a pipe, heated by silite heaters, rotates, a loading device and a control panel. The pipe is supported by four support rollers and a chain drive. The loading device is installed on support wheels with which it can be rolled away from the furnace in case of repair. The inclination of the furnace towards the unloading side can be changed within the range from 0 to 3 ° C. The work is controlled from the console. The gases formed during the firing of powders are sucked off through a branch pipe connected to the shop ventilation system.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for drying bulk materials in various industries: chemical, construction, paint and varnish, powder metallurgy, etc. Hot air supplied to the drying zone from a heat generator is used as a heat carrier. Evaporation products are removed through an air duct, which is connected to the workshop exhaust ventilation through a branch pipe. The characteristics of the drying drum can be changed for the technological tasks of the Customer's production. On request it is completed with a heat generator of any type. Electric or gas, rated thermal power of gas heat generators from 0.315 MW. The installation includes: frame, drum, support station, drive station, loading bunker, unloading bunker.
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
ООО ПКФ ПРОТЕМ
Рыбинск, Russia
Specify the price
Designed for mixing and granulating powder materials. Consists of • an inclined rotating mixing chamber; • high-speed granulating head; • nozzles for binder injection; • scraper tool for dumping the mixture from the wall and bottom of the chamber, preventing sticking; • pneumatic cylinder for opening the bottom unloading valve; control systems. The rotation speed of the mixing chamber and granulating head is regulated by a frequency converter, the time of the mixing, granulating and unloading process is set by a timer for each operation. Loading is carried out manually through the fitting with the chamber closed. Unloading through the bottom hatch. Units and parts in contact with the processed product are made of stainless steel. Various versions are possible both in size and in materials used.
ТОВ "Кооператив Надія"
Черкассы, Ukraine
Specify the price
The filling and packaging machine is designed for filling and packaging liquid dairy and other products in containers made of polymeric materials. The packaging is closed with foil lids with a heat-sealable layer. The machine is equipped with a dating mechanism. Technical characteristics Brand LLC "Cooperative Nadia" Country of origin Ukraine Productivity 1500 pcs / h Productivity, pack./min 20-30 Dosing volume Dose value, ml 50-250 Dosing accuracy,% 2 Power consumption, kW 1 Electric power supply from the alternating current network (1ph): voltage, V 220 Frequency, Hz 50 Required consumption of compressed air (at a pressure of 6-8 bar), l / min 120 Dimensions, mm 770x710x1850 Weight, kg. 220
ТОВ "Кооператив Надія"
Черкассы, Ukraine
Specify the price
The official Qoovee website helps you make profitable deals, find a supplier and manufacturer to grow your business. In the “Directory of suppliers” section you can find for yourself everything you need: Vehicles & parts from Russia, Kyrgyzstan, Kazakhstan, Turkey, Ukraine and other countries. Product categories are constantly updated. Wholesale suppliers are looking for wholesale purchases and partnerships and are ready for mutually beneficial cooperation.
