Measuring instruments in bulk on Qoovee

This table top densitometer displays transmission percent opacity and optical density. Single-Step measurement of %Opacity, %Transmission, and Transmission Optical Density The Tobias TBX2000™ Transmission Densitometer/Opacity Meter measures and calculates percent opacity, percent transmission, and transmission optical density. The unit has been designed for user convenience and error-free measurement. There is no more need to figure the percentages manually. The data can be uploaded to a spreadsheet via the USB port using an optional data transfer program (p/n A2128). To meet special requirements an optional filter carrier may be used allowing supplementary filters to isolate a portion of the spectrum that may be of interest.The TBX2000 has been designed for user convenience and error-free measurement. Table illumination facilitates film placement and the entire operation requires only one hand, leaving the other free for note taking or sample repositioning.Plastic materials are easily read where both the percent opacity and the percentage of light that is not transmitted through the material can be displayed. The unit can also display the density values when required. The unit has both an absolute mode and a relative mode, which can be used for comparing the measured values to a previously stored value for consistent process control. Soft key menu operation 7 inch throat to measure large samples Readings are very repeatable with a large degree of accuracy Calculates opacity and transmission percentage values automatically Can display the density values. USB port standard Software calibration Optional band pass filter Switchable LED table lamps Cost effective and affordable quality control system

These table top densitometers display transmission density and density difference. The TBX1500 also calculates positive and negative dot areas. Single-Step measurement of Transmission Optical Density and Optical Dot Area The Tobias TBX1000™ and TBX1500™ Transmission Densitometers measures transmission optical density. The TBX1500 also calculates positive and negative dot area. The unite have been designed for user convenience and error-free measurement. The data can be uploaded to a spreadsheet via the USB port using an optional data transfer program (p/n A2128). To meet special requirements an optional filter carrier may be used allowing supplementary filters to isolate a portion of the spectrum that may be of interest. The TBX1000 and TBX1500 have been designed for user convenience and error-free measurement. Table illumination facilitates film placement and the entire operation requires only one hand, leaving the other free for note taking or sample repositioning. The unit has both an absolute mode and a relative mode, which can be used for comparing the measured values to a previously stored value for consistent process control. B&W transmission densities Calculates positive and negative dot area (TBX1500) Soft key menu operation 7 inch throat to measure large samples Readings are very repeatable with a large degree of accuracy USB port standard Software calibration Optional band pass filter Switchable LED table lamps Cost effective and affordable quality control system

Digilent Analog Discovery 2: 100MS/s USB Oscilloscope, Logic Analyzer, Pwr Sup... Never Used

Shipping and transportation are not included in the price.

Kit: NuFlo EZ-IN 1 “x2” liquid turbine flowmeter with 6-vane rotor (1 "size, connection: mating with any 2" flange), magnetic sensor for reading the number of passes of blades and NuFlo ™ Flow Analyzer MC-III ™ EXP Explosion Proof Analyzer, manufactured by Cameron. Applications: Turbine meters with a variety of end connections and level of accuracy have the following areas of application: • Measurements when ordering water • Heat treatment plants • Metering and operational separators • Utilization wells • Carbon dioxide injection • Fuel and feed water for steam generators • Liquid dosing Fertilizers • Metering the flow of water, fuel and chemicals in the field • Loading and unloading tanks for chemical products • Metering the consumption of liquid propane • Underground mining and ore leaching * NuFlo MC-III EXP Explosion Proof Analyzer NuFlo Series MC-III ™ EXP Flow Analyzer ™ (Explosion-Proof Extended Display Transmitter) is unmatched as a state-of-the-art, easy-to-use totalizer for liquid and gas flow measurement and data logging, using Modbus communication protocol and equipped with an explosion-proof housing. The MC-III EXP analyzer is capable of storing a large amount of flow information and transmitting it faster than any other flow analyzer on the market. This highly efficient instrument records up to 384 daily data blocks, 768 hour data blocks and 345 event data blocks and can transfer them to a computer in less than a minute using the Modbus® communication protocol! Frequently used operations can be accessed from the front panel six-button keypad or from the dynamic interface software for quick and easy unit calibration and set-up. * Cameron magnetic paddle travel sensor. All can be purchased separately as spare parts. The total cost per kit is $ 3800. When buying the whole lot, 20% discount. Separately, we will consider it personally. A total of 132 sets of 2018. Everything is new in the package. Prices are individually in dollars with VAT per unit. turbine transducer, liquid series NuFlo EZ-IN 1 "x2" - $ 1710, NuFlo MC-III EXP Explosion Proof Analyzer Flow Analyzer - $ 2160, Magnetic Sensor - $ 75.

new vortex flowmeter Proline Prowirl F 200 from Endress + Hauser, manufactured in November 2018, at factory price. Attorney with passport and certificates. Proline Prowirl F 200 Vortex flowmeter Measuring tube made of stainless steel Steel CF3M, Connection DN100, PN40, 1/4404 / F316L EN1092-1-B1 (DIN 2501) flange, 3-point calibration, basic version, ATEX certificate II2G + IECEx Z1 Ex d (ia) IIC Z = Zone, Compact, aluminum, IP67 NEMA4X, M20 cable gland (EEx d: M20 thread), 2 line display; within 4-20 mA HART + pulse-frequency. The flowmeter is included in the register of GSI RK, completed with a certificate of type approval or metrological certification, a valid verification certificate, Year of issue 10. 2018. Prowirl F is a multi-variable flowmeter with integrated wet steam detection. Designed for steam applications and also provides the highest measurement accuracy for gases and liquids in auxiliary processes. Thanks to its unique 2-wire technology, Prowirl F 200 enables cost-effective and easy integration into existing infrastructures. The device also guarantees high operational safety in hazardous areas. Heartbeat Technology ensures continuous process safety

flowmeter manufactured by Siemens 7ME6310-3MF12-2JE1 in the amount of 3 pieces. Year of release 2018. Du80, Ru40. for acidic environments. SITRANS FM MAG 3100 electromagnetic flowmeter sensor (not described) DN80, 3 INCH EN1092-1, PN40 FLANGES CARBON STEEL ASTM A 105 COATING 150MICRON EPDM HASTELLOY C-276 MAG 6000, IP67 / NEMA 4X / 6, CASE, POLISH 115-230V AC 50/60 HZ MODBUS RTU / RS 485 METRIC TERMINAL BOX IN POLYAMIDE OR COMPACT 6000 I.

Counter: turbine, wafer type, EZ - IN series, 1 "x2". Turbine flowmeter, liquid, wafer type, EZ-IN type (device size 1 ", connections: mating with any flange 2"). there is no installation kit for the flow meter. Quantity 132 pieces . 2018 year . ASSY, FLOW ANALYZER, MC-III EXP, LITH PWRD (EXP 9A-50165003 & WP 9A-50165009) 9A-50179024   Part No: 2296694-01; Rev 03 SN : 12112455603 CAMERON USA 03/15/18 The NuFlo ™ Series MC-III ™ EXP Flow Analyzer (Explosion-Proof Extended Display Digitizer) is unmatched as a state-of-the-art, easy-to-use totalizer for liquid and gas flow measurement and data logging using Modbus communications and an explosion-proof enclosure. The MC-III EXP analyzer is capable of storing a large amount of flow information and transmitting it faster than any other flow analyzer on the market. This highly efficient instrument records up to 384 daily data blocks, 768 hour data blocks and 345 event data blocks and can transfer them to a computer in less than a minute using the Modbus® communication protocol! Frequently used operations can be accessed from the front panel six-button keypad or from the dynamic interface software, making it quick and easy to calibrate and tune the unit.   NUFLO EZ-IN Series Turbine Flowmeter Part No: 9A-100062997, Rev 03 ASSY, FM, 1 / 2IN, EZ-N, STD P / N 9A-100005115 a / n Meter SN:   12114198404 CAMERON USA 04/26/18 Max VIP = 25.5MPa Max T = 121 0 C Turbine flowmeters Cameron NuFlo liquid   with EZ IN® end connections with 6 vane rotor (1 "size, connection: mating with any 2" flange). NuFlo Liquid Turbine Meters   are a tool for accurately calculating the flow rate of a fluid flowing through a pipeline. NuFlo Series Turbine Meters indicate flow rate and measure the total volume of fluid flowing through the pipeline. When the liquid flows through the flow meter and the flow around the rotor, the latter rotates with a frequency directly proportional to the flow rate. The movement of the rotor blades is sensed by a magnetic sensing element that generates a sinusoidal electrical signal. This signal is transmitted to indicating measuring devices. Areas of use:   Turbine meters with a variety of end connections and level of accuracy have the following applications: • Measurements when ordering water • Installations for heat treatment • Metering and operational separators • Utilization wells • Carbon dioxide injection • Fuel and feed water for steam generators • Dosing of liquid fertilizers • Measurement of consumption of water, fuel and chemical products in factory conditions • Loading and unloading chemical tanks • Accounting for the consumption of liquid propane • Underground mining and ore leaching     Part Number: 9A-100002077 Rev G Pickup, Nuflo, 7/8, THRU, 8 INCH Cameron 9 A -100002077 Flowmeter Magnetic Pickup Pickup Cameron Nuflo MV-100005111, 9A-100005111 Flow Analyzer Battery Voltage: 3.6 Volts Capacity: 17.0 Ah Chemistry: Lithium-Thionyl Chloride Termination: BA (Button Top - Pressure Terminals) LS33600-CN battery for Cameron Nuflo MC-II plus MC-III, MV-100005111, 9A-1000051

Product Name: Infrared Thermometer Non-touch measurement High precision infrared sensor Practical patent design High definition display 32 groups memory recall

Gas meter "Prince-M" G40 measures the volume of consumed gas up to 65 m³ / h, at a temperature range from -40 to +60 ° С, is used as part of commercial gas metering units, in mobile boiler houses, apartment buildings for access and house gas metering ... The built-in thermocorrector, as well as telemetry of the development and production of the meter manufacturer, allows them to be installed in metering units where accurate readings of the reduced gas volume and remote data collection are required. All devices are guaranteed for 6 years. Maximum working pressure up to 5 kPa. The meter can be used to measure gas in centralized low pressure networks, as well as after the reduction gearbox of gas holders. The design of the device has small dimensions and weight up to 1.2 kg, there are no moving parts, additional maintenance of the gas meter is not required. Pre-installed nuts on DN 50 nozzles allow the meter to be mounted directly on the pipeline. Gaskets are included.

The high accuracy and small dimensions of the Prince-M G25 utility gas meter allows the device to be used as part of a commercial gas metering unit, in production and utilities. Each counter is equipped with a thermocorrector, it is possible to configure additional parameters. The meter operates at temperatures of the measured medium in the range from -40 to +60 ° С. Can be installed outdoors in unheated rooms, in harsh weather conditions. The design of the meter does not contain moving parts, which increases reliability, no additional maintenance is required. The meter is powered by a built-in battery designed for 10 years of operation. For the convenience of data retrieval, it is possible to organize a remote transmission system in various ways, integration with many gas suppliers.

Meters are installed in boiler rooms of production facilities, entrances of apartment buildings and at other facilities where a reliable accurate gas meter is required and space for installing additional equipment is limited. The operating temperature range is from -40 to +60 ° C, which guarantees accurate measurements even in the most severe conditions. The possibility of installation in unheated rooms and outdoors makes the gas meter unique in the utility segment, and the ready-to-use telemetry system allows you to control many meters by one operator. All devices are equipped with a temperature sensor located directly in the gas flow, which, according to the certified measurement procedure, makes it possible to bring the accumulated volume values to standard temperature conditions, it is possible to adjust the compressibility coefficient and set the pressure constant. The calibration interval and the manufacturer's warranty is 6 years, during which the company makes a replacement in case of a defect.

Determination of ozone concentration parameters The ozone concentration in water is measured by one of the following methods: determination of the redox potential; photometry; the use of amperometric sensors; titration. Devices for measuring ozone in air use the following methods during operation: the use of substances that chemically interact with ozone or its decomposition products; photometry; determination of the resistance of a number of metal oxides, etc. The specific method for measuring the concentration of ozone in water or air is determined by the ease of use, the frequency of reading, the financial capabilities of the enterprise and a number of other factors.

УКТ38 измеритель 8-канальный с аварийной сигнализацией предназначено для контроля температуры, давления, влажности, уровня или другой физической величины в нескольких зонах одновременно (до 8-ми) и аварийной сигнализации о выходе любого из контролируемых параметров за заданные пределы, а также для регистрации измеренных параметров на ПК.ОВЕН УКТ38 применяется в качестве аварийного сигнализатора в многозонных печах в пищевой, металлургической и других отраслях промышленности.Контроль температуры или другой физической величины (давления, влажности, уровня и т. п.) в нескольких зонах одновременно (до 8-ми)Восемь входов для подключения датчиков:- термопреобразователей сопротивления типа ТСМ и ТСП 50/100, Pt100;- термопар ТХК, ТХА, ТНН, ТЖК, ТПП(S), ТПП(R);- датчиков с унифицированным выходным сигналом тока 0(4)...20 мА, 0...5 мА или напряжения 0...1 В.Подключение к разным входам датчиков разных типов из числа приведенных в списке для одной модификацииСигнализация «АВАРИЯ ОБЪЕКТА» о выходе любой из контролируемых величин за заданные пределыСигнализация «АВАРИЯ ДАТЧИКА» при обрыве или коротком замыкании датчикаДва выходных реле для включения аварийной сигнализации или аварийного отключения установкиИндикация измеренных величин и заданных для них уставок на двух встроенных индикаторахПрограммирование кнопками на лицевой панели прибораСохранение заданных параметров при отключении питанияРегистрация контролируемых параметров на ЭВМ через адаптер сети ОВЕН АС2 по интерфейсу RS-232

Прибор ОВЕН ТРМ200 – двухканальный измеритель, применяемый для измерения температуры, уровня, давления, влажности, веса и других физических параметров теплоносителей и различных сред (в зависимости от подключенных датчиков). Измерительный прибор ОВЕН ТРМ200 предназначен для использования в холодильных установках, сушильных шкафах, печах, пастеризаторах и на другом технологическом оборудовании.Два универсальных входа для подключения широкого спектра датчиков (температуры, давления, уровня и других физических параметров).Два ярких светодиодных индикатора, позволяющих отображать измеренные значения с двух входов, их разность, квадратный корень4 типа корпуса: Н, Щ1, Щ2, Н2Цифровая фильтрация и коррекция входного сигнала, а также масштабирования шкалы для аналогового входаИнтерфейс RS-485 (протокол ОВЕН, Modbus ASCII/RTU)Несколько уровней защиты настроек прибора для разных групп специалистовПрограммирование с лицевой панели или из конфигуратора

Измеритель 2ТРМ0 предназначен для измерения температуры теплоносителей и различных сред в холодильной технике, сушильных шкафах, печах различного назначения и другом технологическом оборудовании, а также для измерения других физических параметров (веса, давления, влажности и т. п.).Класс точности 0,5 (термопары)/0,25 (другие типы сигналов). Регулятор выпускается в корпусах 5 типов: настенном Н, монтаж на Дин-рейку Д и щитовых Щ1, Щ11, Щ2.Улучшенная помехоустойчивость: 2ТРМ0 полностью соответствует требованиям ГОСТ Р 51522 (МЭК 61326-1) по электромагнитной совместимости для оборудования класса А (для промышленных зон) с критерием качества функционирования А;Повышенная надежность: наработка на отказ составляет 100 000 часов;Повышенная точность измерений: погрешность измерений не превышает 0,15 % (при классе точности 0,25/0,5);Межповерочный интервал – 3 года;Гарантийный срок обслуживания 2ТРМ0 составляет 5 лет;Улучшенные показатели климатического исполнения: допустимый диапазон рабочих температур от –20 до +50 °С;Универсальные входы: прибор поддерживает все наиболее распространенные типы датчиков;Расширенный диапазон напряжений питания: 90...245 В частотой 47...63 Гц;Встроенный источник питания 24 В во всех модификациях нового 2ТРМ0 для питания активных датчиков или других низковольтных цепей АСУ

Счетчики холодной воды комбинированные ВСХНК, ВСХНКд предназначены для измерений объема холодной воды в напорных трубопроводах в системах холодного водоснабжения при температуре от 5 до 50 °С и давлении воды до 1,6 МПа (16 кгс/см2).Счетчики комбинированные применяются на промышленных объектах, объектах коммунального хозяйства и в составе автоматизированных систем контроля и учета холодной воды. Они разработаны специально для объектов с широким диапазоном расхода воды, непостоянным уровнем расхода, варьирующим в течении суток, сезонов или условий технологического процесса, объектов кратковременного учета большого расхода, где при нормальной ситуации протекает небольшое количество воды.

Характеристики:Тип: крыльчатый, одноструйный, сухого типаПрисоединение: резьбовоеТемпература воды: +5...+50СДиапазон расхода: 0,07...7 м3/часНоминальный расход: 3,5 м3/чМонтажная длина: 260 ммВыход: герконовый 10 л/импМонтаж: горизонтальное положениеПрямые участки: 5ДУ перед и 1ДУ после счетчикаМежповерочный интервал: 6 летГарантия: 2 года.Водомеры ВСХД-25 используются для измерения объемов холодной воды:Объемами потребления до 7,0 м3/час и до 87 м3/сутки;в потоках по трубам диаметром до одного дюйма;под рабочим давлением до 1,6 МПа.Качество воды регламентировано нормативными документами. Вода не должна содержать твердых включений и растворенных химических элементов, которые, оседая на поверхности лопастей крыльчатки, приводят к искажению показаний.В счетчики ВСХД-25 вмонтирован магнитный датчик, срабатывающий каждый раз после прохождения через счетчик воды в объеме десяти литров. Включение датчика формирует импульс, который по проводам регистрируется считывающими устройствами и преобразует его в числовое обозначение.

Характерсистики: Тип: крыльчатый, одноструйный, сухого типаПрисоединение: резьбовоеТемпература воды: +5...+150СДиапазон расхода: 0,14...7 м3/часНоминальный расход: 3,5 м3/чМонтажная длина: 260 ммМонтаж: горизонтальное положениеПрямые участки: 5ДУ перед и 1ДУ после счетчикаМежповерочный интервал: 4 годаГарантия: 2 года.Широкий температурный диапазон +5 до +150 0С позволяет эффективно применять счетчики ВСГ-25 для измерения до 7, 0 м3/час., 89 м3/сутки объема горячей и холодной воды, протекающей по трубопроводам диаметром до 1" под давлением до 1,6 МПа. Вода не должна иметь твердых и растворенных примесей. Качество очистки воды регламентируется нормами ГОСТ для питьевой воды и СНиП для технической. Показания ведутся стрелочными и роликовыми индикаторами, фиксирующими полные м3 и доли до 0,5л.

Характеристики:Тип: крыльчатый, одноструйный, сухого типаПрисоединение: резьбовоеТемпература воды: +5...+50СДиапазон расхода: 0,07...7 м3/часНоминальный расход: 3,5 м3/чМонтажная длина: 260 ммМонтаж: горизонтальное положениеПрямые участки: 5ДУ перед и 1ДУ после счетчикаМежповерочный интервал: 6 летГарантия: 2 года.Счетчики ВСХ-25 применяют для проведения измерений и учета объема расходуемой технической и питьевой холодной воды. Они предназначены для установки на трубопроводах с диаметром проходного отверстия 25 мм. Данные измерений отображаются цифрами на табло при помощи роликового и стрелочного указателя и показывают расход воды в метрах кубических с точностью до долей. Счетчики этой марки применяются для учета расхода воды в промышленных масштабах и могут быть установлены в цехах или лабораториях различных предприятий.

Счетчик горячей воды с импульсным выходом ВСТ-20 - предназначен для измерения объема воды в системах отопления с малым потреблением. Прибор изготавливается из высококачественных комплектующих и отвечает всем европейским и российским стандартам качества. Все приборы оснащены современной антимагнитной защитой, что препятствует влиянию внешнего магнитного поля. Межповерочный интервал 6 лет.

Dynamometers electronic DM-MG4 are certified as standards of the 2nd category and are used for checking presses and testing machines in metrological centers. In scientific and testing laboratories, universities they are used in test benches - where an accurate measurement of force is required. The devices consist of an electronic unit and a sensor, a feature of the dynamometers are two modes of power supply: autonomous (batteries) and a 220 V network. The electronic unit has a large backlit display, the results are displayed on the screen and stored in the device's memory. The PC communication program transfers data to the PC via the USB port. It is not necessary to send the device to the manufacturer for updating - there is a program for remote updating of service functions.

The measuring principle is capacitive, does not depend on the nature of the gas, absolute pressure; the material of the sensor and the body of the device is polymer, chemically resistant; the measuring range, mbar - 1080–0.1; measurement accuracy - ± 1 mbar (after adjustment, at constant temperature); the number of sensors connected to one device - 8 (up to 4 VSP 3000 and 4 VSK 3000 ); operating temperature, ° С - 10–40 ; short-term permissible temperature, ° С - 40–80; memory for 32,000 measurements; RS 232С interface; cable, length, m - 2 (included), up to 30 m (optional); dimensions, L x W x H, mm - 144 × 124 × 114; weight, g - 440.

Combined cold water meters VSKHNK, VSKHNKd are intended for measuring the volume of cold water in pressure pipelines in cold water supply systems at temperatures from 5 to 50 ° C and water pressure up to 1.6 MPa (16 kgf / cm2). Combined meters are used at industrial facilities, municipal facilities and as part of automated control systems and accounting for cold water. They are specially designed for facilities with a wide range of water flow rates, variable flow rates varying during the day, seasons or process conditions, objects of short-term metering of high flow rates, where a small amount of water flows under normal conditions.

VSGd-20 water meters allow you to monitor the actual water consumption: From sensors in the meter body, recording the volume of flowing water in fractions of m3 and full cubic meters. From the built-in reed switch a magnetic interrupter, which is mechanically connected to the impeller, it periodically turns on when each liter of water passes through the meter. Pulse switching on the reed switch generates an electrical signal that is sent through wires to the recording device, where it is converted in the numerical value of the water consumption. Thus, continuous remote recording of measurement results is carried out.

VSKhd-20 water meters are used to control the volume of cold water flow that meets the standards of 51232-98 and sanitary rules 2.04.07-86. The water flow must correspond to certain parameters: the largest delivery volume 5.0 m3 / hour, 63 m3 / day, water temperature +5 to +50 0С, pressure up to 1.6 MPa, < / li> water pipe diameter up to ¾ inch. Getting results Water consumption data is sent to the computer by means of electrical impulses that are generated when the reed switch is turned on built into the VSKhD-20 meters. The reed switch switching mechanism is connected to the impeller and is configured to operate when one liter of water passes. The impulse is fed through the wires to the computer, and a special program transforms the electrical impulses into a system of numerical values.

Water meters VSG-20 are used to accurately measure the amount of consumed cold or hot water under the following conditions: water temperature range from +5 to +95 0С; pressure up to 1.6 MPa; maximum flow 5.0 m3 / h, 63 m3 / day; the diameter of water pipes up to 3/4 inch. The water must be free of solid impurities and soluble salts. The water quality must comply with the standards and sanitary rules. The VSG-20 water meters are equipped with four pointer sensors that record the share of m3 and a roller sensor for reading full cubic meters. The connection is made with threaded couplings with a diameter one inch.

VSX-20 meters are used to measure and account for the volume of network and drinking cold water in pipelines with an inner diameter of 20 mm. The counting mechanism of the water meter has pointer and roller indicators, which show the measured volume of the working medium passing through the pipeline in cubic meters and its shares. The scope of application of metering devices of this brand is wide, starting from utilities and residential buildings, ending with industrial enterprises. Advantages of using VSX-20 meters simplicity of the device, reliability, long service life subject to certain conditions, the possibility of installation using connectors on any part of the pipeline, < li> small dimensions and the ability to install in limited space, can be installed both horizontally and vertically.

VSHd-15 meters are used to measure the flow of cold water. They are designed for installation on 15 mm diameter pipelines. The letter "d" in the model name means that it is equipped with a reed switch, which allows you to remotely monitor the readings of the device. This is very convenient for cases when apartment owners do not want to install a water meter in an open place, choosing a location behind the plumbing or washing machine. Given the diameter of the pipeline, water meters of this type are most often used in everyday life, but they can be installed in laboratories, offices, institutions, retail outlets and institutions of various types. Features of operation < / p> VSHd-15 water meters are used to measure the flow rate of water with a temperature from +5 to + 50 ° C, supplied with a pressure not higher than 1.6 MPa. Other restrictions include: indoor air temperature from +5 to + 50 ° С, availability of heating in winter, humidity less 80%, no possibility of flooding the room and, in particular, the installation site of the device, the impossibility of increasing the maximum permissible temperature of the water passing through the pipeline, constant filling water, the absence within 2 meters of devices or objects capable of creating a magnetic field, the maximum possible volume of water passed through the meter - 38 m3 per day and 1125 m3 per month, work at maximum load no more than 1 hour per day.

Water meters VSG-15 with a diameter of the working passage DN 15, belong to the category of single-channel, clutch dry meters. They are intended for measuring the volume of cold and hot water, as well as for domestic and industrial use. Water moves through pipelines with a diameter of up to 1/2 inch, with a maximum consumption: 3.0 m3 / hour, 36.0 m3 / day. The quality of the water must comply with all sanitary standards that relate to drinking water, as well as the requirements of the technical standards, namely: the highest pressure in the pipeline can be 16 kgf / cm2; the permissible temperature range of water is from +5 to +95 ° C. In addition, the presence of solid impurities that can damage the impeller is not allowed in the water. Even minor violations can lead to problems, namely, the accuracy of the measurement. The meter readings are made by roller and pointer gauges, which record fractions and whole cubic meters of water.

Counters of the VSX-15 brand are used to measure the volume of water passing through the supply pipeline of the cold water supply system with a bore diameter of 15 mm. Vane-type water meters of this type are equipped with a counting mechanism with pointer and roller indicators. VSH-15 advantages simple design durable materials of components especially in parts in contact with water high degree of anti-magnetic protection European assembly quality

Water meters VSG-15 with a diameter of the working passage DN 15, belong to the category of single-channel, clutch dry meters. They are intended for measuring the volume of cold and hot water, as well as for domestic and industrial use. Water moves through pipelines with a diameter of up to 1/2 inch, with a maximum consumption: 3.0 m3 / hour, 36.0 m3 / day. The quality of the water must comply with all sanitary standards that relate to drinking water, as well as the requirements of the technical standards, namely: the highest pressure in the pipeline can be 16 kgf / cm2; the permissible temperature range of water is from +5 to +95 ° C. In addition, the presence of solid impurities that can damage the impeller is not allowed in the water. Even minor violations can lead to problems, namely, the accuracy of the measurement. The meter readings are made by roller and pointer gauges, which record fractions and whole cubic meters of water.

Counters of the VSX-15 brand are used to measure the volume of water passing through the supply pipeline of the cold water supply system with a bore diameter of 15 mm. Vane water meters of this type are equipped with a counting mechanism with pointer and roller indicators. Advantages of ВСХ-15 simplicity of design durable materials of the components especially in the parts in contact with water high degree of anti-magnetic protection European assembly quality

Characteristics : Type: turbine, dry type Connection: flanged < li> Water temperature: +5...+150C Flow rate range: 0.7 ... 30 m3 / h Nominal flow rate: 15.0 m3 / h Installation length: 200 mm Installation: horizontal and vertical position Straight sections: 3DB before and 1DB after meter Calibration interval: 4 years Warranty: 2 years. The VSGN-50 hot water meter is designed to measure the volume of network and drinking water in hot water supply systems with medium and high consumption. The device is made of high-quality components of the Apator-PoWoGaz (Poland) plant and meets all European and Russian quality standards. Calibration interval 4 years.

Characteristics : Type: turbine, dry type Connection: flanged < li> Water temperature: +5 ... +50C Flow rate range: 0.45 ... 90 m3 / h Nominal flow rate: 50.0 m3 / h Installation length: 200 mm Installation: horizontal and vertical position Straight sections: 3DB before and 1DB after meter Calibration interval: 6 years Warranty: 2 years. Cold water meter VSKHN-50 - designed to measure the volume of network and drinking water in cold water supply systems with medium and high consumption. The device is manufactured from high-quality components of the Apator-PoWoGaz (Poland) plant and meets all European and Russian quality standards. Calibration interval is 6 years.

Characteristics : Type: turbine, dry type Connection: flanged < li> Water temperature: +5 ... +50C Flow rate range: 0.45 ... 60 m3 / h Nominal flow rate: 30.0 m3 / h Installation length: 200 mm Outlet: reed 100 l / imp Installation: horizontal and vertical position Straight sections: 3DU in front of and 1DU after meter Calibration interval: 6 years Warranty: 2 years. Cold water meter with pulse output VSKHNd-40 - designed to measure the volume of network and drinking water in cold water supply systems with medium and high consumption. The device is manufactured from high-quality components of the Apator-PoWoGaz (Poland) plant and meets all European and Russian quality standards. Calibration interval 6 years.

Characteristics : Type: turbine, dry type Connection: flanged < li> Water temperature: +5 ... +50C Flow rate range: 0.45 ... 60 m3 / h Nominal flow rate: 30.0 m3 / h Installation length: 200 mm Installation: horizontal and vertical position Straight sections: 3DB before and 1DB after meter Calibration interval: 6 years Warranty: 2 years. Tachometric turbine meters with flange connection of the VSKhN brand are used for measuring and metering cold water consumption. They are installed on industrial pipelines supplying mains and potable cold water with a bore diameter of 40 mm. Metering devices measure the volume of water passed through the pipeline in cubic meters and fractions. Measurement data are displayed on the dial using roller and dial indicators. Operating conditions VSHN-40 meters are installed on cold water supply systems with a working flow temperature from +5 to + 50 ° С and water supply pressure no more than 1.6 MPa. The manufacturer recommends placing measuring devices of this type in closed heated rooms with an air humidity of no more than 80% and an ambient temperature of at least +5 ° C. The place of installation is chosen so that the possibility of flooding of the device is excluded. For this, the meters are placed at a certain height from the floor on a flat horizontal section of the pipeline, constantly filled with water. The manufacturer guarantees uninterrupted operation of the device and high measurement accuracy for at least 6 years. At the end of this period, verification should be carried out, based on the results of which a decision is made to extend the life of the water meter. Among the conditions that guarantee the invariability of the operational characteristics of the VSKHN-40 meter include the correct installation, as well as compliance with the requirements of regulatory documents regarding the maximum possible volume of water passed through the pipeline per day and per month.