All Construction Materials suppliers from Russia

Building materials, finishing materials, both internal and external. Terrace board - corpulent, hollow. A variety of colors and mounting options. Different sizes.

Granite tile TAN BROWN (TEN BROWN) of a noble, saturated dark brown color with a copper shade and with small black inclusions. It is one of the most popular natural stones from India. Sometimes it can be found under the name: DARK TAN GRANITE or ENGLISH BROWN. The structure is medium and coarse, uniform. The surface lends itself to any processing. In the warehouses of the Venice Stone company there is always available tile sizes 600x300x15, 600x300x18, 600x300x30, 600x600x18 and 600x600x30 mm with a polished and heat-treated surface. Granite tiles TAN BROWN are used for exterior cladding: facade, basement, porch, steps, landscape gardening. In interior decoration, tiles are most often used on floors in rooms with high traffic: metro, shopping centers, medical centers, etc.

The tile from the Chinese granite SUNSET GOLD (SANSET GOLD) is beige-pink in color with light golden inclusions. This stone, depending on the party, can be either saturated yellow or light, beige. This makes it possible to choose the right shade for any finish and emphasizes the natural origin of the material. In China, this stone can be found under the name CHINA YELLOW or G682. The structure is medium-grained, homogeneous. The surface lends itself to any processing. Available in the warehouses of the company Venice Stone, tiles are presented in sizes 600x300x18, 600x300x20, 600x300x30, 600x600x18, 600x600x20 and 600x600x30 mm with a polished, heat-treated and bruchardized surface. SUNSET GOLD granite tiles are often used for interior decoration of walls and floors, stairs and steps, as well as for outdoor works in the decoration of facades, socles, stairs and entrance groups, in paving sidewalks and landscape gardening.

Tiles made of Chinese granite SESAME BLACK (SESAM BLACK) of a noble dark gray color with a light ash tint. On the market it can be found under the name PADANG DARK or G654. The structure is fine-grained, homogeneous. The surface lends itself to any processing. Available in the warehouses of the company Venice Stone tiles are presented in sizes 600x300x18, 600x300x20, 600x300x30, 600x600x18, 600x600x20 and 600x600x30 mm with a polished and heat-treated surface. The main advantage of this granite is its fine grain, a consequence of this natural feature is its high strength, low abrasion and resistance to chemistry. SESAME BLACK granite tiles can be seen in paving sidewalks, car parks, stairwells, plinths and facades, building interiors, metro halls, as well as decor elements, fountains, columns.

The tile is made of Chinese granite BELLA WHITE, which is popularly called “salt and pepper” because of its color: dark gray and black inclusions on a white background. This granite has earned popularity among lovers of natural stone and architects due to its characteristics: light colors, natural strength, versatility and affordable cost. In China, this stone can be found under the classification G603. The structure is fine-grained, homogeneous. The surface lends itself to any processing. Available in the warehouses of the company Venice Stone tiles are presented in sizes 600x300x18, 600x300x20, 600x300x30, 600x600x18, 600x600x20 and 600x600x30 mm with a polished and heat-treated surface. The polished surface of the stone looks great in wall and floor coverings, in flights of stairs. BELLA WHITE is a very strong and resistant stone. Applicable for such outdoor works as: facing socles and building facades, masonry walkways and sidewalks, in landscape design. The low level of water absorption allows the use of stone in the decoration of pools and fountains.

The tile is made of Chinese granite BAINBROOK BROWN (BEYNBRUK BROWN) warm brown-pink shade. Due to its complex color scheme, it looks very elegant and solid. Having a stylish look, this stone always finds admirers who appreciate it for its beauty, pleasant color and strength. On the market you can find analogues of this material under the Chinese classification G664. The structure is medium-grained, homogeneous. The surface lends itself to any processing. Available in the warehouses of the company Venice Stone, tiles are presented in sizes 600x300x18, 600x300x30, 600x600x18 and 600x600x30 mm with a polished and heat-treated surface. BAINBROOK BROWN granite tile has been widely used in cladding of plinths and building facades, laying of walkways and sidewalks, in landscape design. The low level of water absorption allows the use of granite in the decoration of pools and fountains. The stone has a medium-grain structure, high strength, is resistant to fading and temperature changes, safe and environmentally friendly.

Tiles from Indian granite ABSOLUTE BLACK (ABSOLUT BLACK) intense black without additional inclusions. Such coloring makes this stone not only as practical as possible, but also an ideal solution for interior design. The structure is fine-grained, homogeneous. The surface lends itself to any processing. Available in the warehouses of the company Venice Stone tiles are presented in sizes 600x300x15, 600x300x18, 600x300x20, 600x300x30, 600x600x18, 600x600x20 and 600x600x30 mm with a polished and heat-treated surface. The scope of granite tiles ABSOLUTE BLACK is very wide: it is the interior and exterior decoration, small architectural forms, as well as landscape design. It is harmonious in the interiors of any stylistic orientation and color scheme. Ideal for flooring, steps, flights of stairs.

Secondary concrete crushed stone by shipment at own expense or with delivery across Moscow and Moscow region Fractions 5-20 - 700 r / cu m 20-40 - 550 r / cc m 40-70 - 500 r / cu. m 0-70 - 350 r / cu m Screening concrete 0-5 - 120 r / cu. m

Professional building polymer glue,   packing - a tube (cartridge) under a construction gun 310 ml .: Appointment: for gluing products from PVC, particleboard, MDF,   polystyrene foam, polyurethane foam, wall panels, cork, wood, cardboard ceramics, glass, metal, gypsum, brick, drywall, decorative stone   to various substrates - concrete, brick, plaster, wood, gypsum board, fiberboard, chipboard, etc. It is used for interior and exterior, at a temperature from -10 0 C to +30 0 C. Colour:   transparent or white Composition: vinyl acetate polymers, functional additives                                          Properties: ·                      initial setting time 15 minutes ·                      setting force 90 kg / m 2 . ·                      waterproof, frost resistant ·                      after drying, the adhesive joint is clear or white             (depending on the item).

Repair mixture for concrete ICBM 500 Appointment : Dry construction mix MBR 500 is intended for the preparation of building fine-grained concrete (mortar) used for repairing concrete structures, monoling joints, technological holes, sealing cracks in concrete, brick walls, ceilings, etc. Composition :             Dry construction mix MBR 500   is a polymer-mineral fine-grained mixture obtained by intensive mixing of fractionated sand, Portland cement and a complex of modifying additives. Concrete preparation : For the preparation of dry building mix MBR 500   pour into clean fresh water, constantly mixing until a homogeneous mass is obtained using an electric drill with a mixer nozzle or a low-speed forced-action mixer. The amount of water required for the preparation of concrete is determined from the ratio of 0.18-0.19 l per 1 kg of dry construction mixture. Excess water contributes to the formation of cracks. Ready concrete must be used within 15 minutes. Preparation of the working surface (base) : The working surface (base) must be strong, durable, free of dust, dirt, oils, fats, wax, bitumen, paint residues, cement milk, efflorescence. Cracks are broken, old fragile concrete is removed, the released reinforcement is cleaned of rust. The prepared surface is cleaned of dust with compressed air, washed with water or treated with a sandblasting machine. It is necessary to treat with a polymer-mineral primer weak and highly absorbent substrates. Metal parts must be treated with an anti-corrosion solution. Concrete Application : Before applying concrete, the prepared surface is abundantly moistened. The water is allowed to soak and then manually apply concrete with a spatula. It is necessary to reinforce the applied repair layer with large areas of the surface to be repaired, repair of places subject to large bending loads, and a concrete layer thickness of more than 50 mm. Concrete laying is carried out without interruption until complete completion, or by grips. Before applying subsequent layers, it is necessary to moisten the previous layer, i.e. observe the processing method - “wet on wet”. The temperature of the working surface should be at least + 5ºС and not more than 30ºС. At negative temperatures up to -10ºС, the repair mixture MBR500M is used. To prepare the solution, it is necessary to use water at a temperature of at least 15 ° C. Stir the solution until the antifreeze additive is completely dissolved for at least 5 minutes from the moment of adding water. The consumption of dry mix depends on the type of repair. To repair a damaged horizontal surface with a repair layer thickness of 50 mm, 95-110 kg of mixture per 1 sq.m. To close a hole in a concrete wall with a diameter of 30-35 mm and a depth of 10 cm, 150-200 g of mixture is required, to close a crack with a width of 20 mm and a length of 1 m at a depth of 20 mm, 700-750 g of mixture are required. Specifications : Astringent Portland cement Aggregate fractionated sand Placeholder fraction up to 1.0 mm Water retention capacity not less than 9 5 % Maximum thickness in one run 50 mm Water consumption for cooking 0.18-0.19 L per 1 kg of mixture Viability not less than 60 min Work surface temperature For MBR-500 For MBR-500M   from + 5˚С to + 30˚С from -10˚С to + 5˚С Compression strength after 28 days (grade) 500 kgf / m 2 (50 MPa) Peel strength from concrete surface 17.5 kgf / m 2 (1.75 MPa) Frost resistance no less than 400 cycles Water resistant not less than W 10 Safety precautions : Portland cement contained in the mixture, when interacting with water, forms an alkali. Avoid getting ready-made mortar on the skin and mucous membranes. In case of contact, rinse the contact area with clean running water.             Strength chart of ICBM 500M (seven-day strength calculation) No. p / p Hardening temperature, ° С The strength in the samples is 70.7x70.7x70.7 mm when hardening for 1 day 3 days 7 days 14 days 28 days 1 twenty 15.8 22.4 32,7 40.5 51.0 2 -5 3.3 10.0 18.1 20.8 28.5 3 -10 2,4 8.1 14.5 17.8 26.9   The set of strength can vary within the permissible variation of 15%.   Shelf life : Store mortar in a dry place at a relative humidity of 60%, temperature from –50 to +50 ˚С. Shelf life in the manufacturer’s packaging 6 months from the date of manufacture

Repair mixture for concrete   ICBM 400   Appointment : Dry construction mix MBR 400 is intended for the preparation of building fine-grained concrete used for repairing concrete structures, monoling joints, technological holes, filling cracks, etc.   Composition :             Dry construction mix MBR 400   is a polymer-mineral fine-grained mixture obtained by intensive mixing of fractionated sand, Portland cement and a complex of modifying additives.   Concrete preparation : For the preparation of dry building mix MBR 400   poured into clean fresh water, constantly mixing until a homogeneous mass with a wooden spatula, electric drill with mixer nozzle or low-speed forced-action stirrer. Mixing is carried out for at least 5 minutes. The amount of water required for the preparation of concrete is determined from the ratio of 0.2-0.22 L per 1 kg of dry construction mixture (5.5-5.75 L of water per bag of 25 kg of dry construction mixture). The exact amount of water is determined when the consistency required for the work, the plasticity of the building concrete, is achieved. Ready concrete to stand   for 5 minutes to obtain complete homogeneity and then re-mix. Ready concrete must be used within 1 hour.   Preparation of the working surface (base) : The working surface (base) must be strong, durable, free from dust, dirt, oils, fats, wax, bitumen, paint residues. Cracks are broken, old fragile concrete is removed, the released reinforcement is cleaned of rust. The prepared surface is cleaned of dust using compressed air. Weak old concrete or mortar reinforced with polymer-mineral primer Apply a highly absorbent surface to the primer. Metal parts must be treated with an anti-corrosion solution.   Concrete Application : Before applying concrete, the prepared surface is abundantly moistened. Allow the water to soak in and then apply the concrete manually. For large areas of the surface to be repaired, repair of places subject to large bending loads, the layer of applied concrete, the thickness of the concrete layer of more than 50 mm must be reinforced with an alkali-resistant fiberglass mesh, metal reinforcement or fiber. Concrete laying is carried out without interruption until complete completion, or by grips. Before applying subsequent layers, it is necessary to moisten the previous layer, i.e. observe the processing method - “wet on wet”. The temperature of the working surface should be at least + 5ºС and not more than 30ºС. Concrete consumption depends on the type of repair. To repair a damaged horizontal surface of 95-110 kg per 1 sq. M of the surface to be repaired with a layer thickness of 50 mm.   Specifications : Colour Gray Astringent Portland cement Aggregate fractionated sand Placeholder fraction up to 1.0 mm Water retention capacity not less than 98% Maximum thickness in one run 50 mm Water consumption for cooking 0.2-0.22 L per 1 kg of mixture Viability at least 1 hour Hardening time 24 hours Work surface temperature from + 5˚С to + 30˚С Compressive strength (grade) 400 kgf / m 2 (40 MPa) Peel strength from concrete surface 17.5 kgf / m 2 (1.75 MPa) Frost resistance no less than 400 cycles   Safety precautions : Portland cement contained in the mixture, when interacting with water, forms an alkali. Avoid getting ready-made mortar on the skin and mucous membranes. In case of contact, rinse the contact area with clean running water.   Shelf life : Store mortar in a dry place at a relative humidity of 60%, temperature from –50 to +50 ˚С. Shelf life in the manufacturer’s packaging 6 months from the date of manufacture

Repair mixture for concrete   ICBM 300   Appointment : Dry construction mix MBR 300 is intended for the preparation of building fine-grained concrete used for repairing concrete structures, monoling joints, technological holes, sealing cracks, etc.   Composition :             Dry construction mix MBR 300   is a polymer-mineral fine-grained mixture obtained by intensive mixing of fractionated sand, Portland cement and a complex of modifying additives.   Concrete preparation : For the preparation of dry building mix MBR 300   poured into clean fresh water, constantly mixing until a homogeneous mass with a wooden spatula, electric drill with mixer nozzle or low-speed forced-action stirrer. Mixing is carried out for at least 5 minutes. The amount of water required for the preparation of concrete is determined from the ratio of 0.2-0.22 L per 1 kg of dry construction mixture (5.5-5.75 L of water per bag of 25 kg of dry construction mixture). The exact amount of water is determined when the consistency required for the work, the plasticity of the building concrete, is achieved. Ready concrete to stand   for 5 minutes to obtain complete homogeneity and then re-mix. Ready concrete must be used within 1 hour.   Preparation of the working surface (base) : The working surface (base) must be strong, durable, free from dust, dirt, oils, fats, wax, bitumen, paint residues. Cracks are broken, old fragile concrete is removed, the released reinforcement is cleaned of rust. The prepared surface is cleaned of dust using compressed air. Weak old concrete or mortar reinforced with polymer-mineral primer Apply a highly absorbent surface to the primer. Metal parts must be treated with an anti-corrosion solution.   Concrete Application : Before applying concrete, the prepared surface is abundantly moistened. Allow the water to soak in and then apply the concrete manually. For large areas of the surface to be repaired, repair of places subject to large bending loads, the layer of applied concrete, the thickness of the concrete layer of more than 50 mm must be reinforced with an alkali-resistant fiberglass mesh, metal reinforcement or fiber. Concrete laying is carried out without interruption until complete completion, or by grips. Before applying subsequent layers, it is necessary to moisten the previous layer, i.e. observe the processing method - “wet on wet”. The temperature of the working surface when applying MBR300 should be not less than + 5ºС and not more than 30ºС. The temperature of the working surface when applying MBR300M should be at least -10ºС and not more than + 5ºС. Concrete consumption depends on the type of repair. To repair a damaged horizontal surface of 95-110 kg per 1 sq. M of the surface to be repaired with a layer thickness of 50 mm.   Specifications : Colour Gray Astringent Portland cement Aggregate fractionated sand Placeholder fraction up to 1.0 mm Water retention capacity not less than 98% Maximum thickness in one run 50 mm Water consumption for cooking 0.2-0.22 L per 1 kg of mixture Viability at least 1 hour Hardening time 24 hours Work surface temperature For MBR-300 For MBR-300M   from + 5˚С to + 30˚С from -10˚С to + 5˚С Compressive strength (grade) 300 kgf / m 2 (30 MPa) Peel strength from concrete surface 18 kgf / m 2 (1.8 MPa) Frost resistance no less than 400 cycles   Safety precautions : Portland cement contained in the mixture, when interacting with water, forms an alkali. Avoid getting ready-made mortar on the skin and mucous membranes. In case of contact, rinse the contact area with clean running water.   Shelf life : Store mortar in a dry place at a relative humidity of 60%, temperature from –50 to +50 ˚С. Shelf life in the manufacturer’s packaging 6 months from the date of manufacture

Ceramic tile 115.5 * 200mm (Glossy) (MDT-40) Small format tiles.  

Glass mosaic 8 * 23 * 48 * 98 * 297mm (MDS-37) Collection STYLE

Glass mosaic 4 * 10 * 318mm (MDP-01) PREMIUM Collection

Glass mosaic 8 * 23 * 300mm (MDS-22) Collection STYLE

Glass mosaic 4 * 300 * 300mm (MDS-49) Collection STYLE.

Glass mosaic 4 * 20 * 327mm Fantasy collection. MDF-70

Glass mosaic (mix) 4 * 20 * 327mm. Fantasy Collection MDF-04

Ceramic tile 98 * 98mm (TCMBAK-1). MDT-01 (Matte; Gloss).

The additive is intended: 1. To ensure the waterproofing of concrete and reinforced concrete structures. 2.Increases water resistance, frost resistance, concrete strength. 3. Protects the concrete structure from the effects of wastewater and groundwater, sea water, oil products, aggressive environments: acids, alkalis, etc. 4. Increases the corrosion resistance of concrete, prevents corrosion of steel reinforcement. Technical characteristics of "_BAFF 02 Gel": 1. Increasing the water resistance of concrete by at least 3 steps according to GOST 12730.5-84: - for concrete grade B20, increased water resistance from W2 to W8, - for concrete grade B30, increased water resistance from W6 to W14, 2.When increasing the BAFF 02 additive content to 2% of the cement mass in concrete B30, the water resistance index is greater than W14. 3. Increase in frost resistance to 300 cycles in accordance with GOST 26633. 4. The increase in compressive strength according to GOST 10180-90 - not less than 2.5% for concrete B30 - not less than 25% for concrete B20. The mechanism of action of functional chemical additives "BAFF 02": When BAFF 02 and BAFF 02 Gel additives are added to concrete, the chemical salts of the complex salts that make up the additive react with the calcium, aluminum and iron ions present in the concrete (concrete product) to form supersaturated solutions of insoluble complexes. In the process of concrete curing, insoluble complexes in the form of needle-shaped crystals crystallize from supersaturated solutions in the form of pores in the concrete body. Strength indicators of concrete increase. During the operation of concrete, needle crystals prevent the diffusion of water droplets through pores and microcracks (up to 0.4 mm) inside the concrete body, thereby improving the concrete's waterproof and frost resistance characteristics. Needle-shaped crystals allow excess moisture to freely exit the concrete body in the form of water molecules (the vapor permeability of concrete is preserved).

The additive is intended: 1. To ensure the waterproofing of concrete and reinforced concrete structures. 2.Increases water resistance, frost resistance, concrete strength. 3. Protects the concrete structure from the effects of wastewater and groundwater, sea water, oil products, aggressive environments: acids, alkalis, etc. 4. Increases the corrosion resistance of concrete, prevents corrosion of steel reinforcement. Specifications of "_BAFF 02" 1. Increasing the water resistance of concrete by at least 3 steps according to GOST 12730.5-84: - for concrete grade B20, increased water resistance from W2 to W8, - for concrete grade B30, increased water resistance from W6 to W14, 2.When increasing the BAFF 02 additive content to 2% of the cement mass in concrete B30, the water resistance index is greater than W14. 3. Increase in frost resistance to 300 cycles in accordance with GOST 26633. 4. The increase in compressive strength according to GOST 10180-90 - not less than 2.5% for concrete B30 - not less than 25% for concrete B20. The mechanism of action of functional chemical additives "BAFF 02": When BAFF 02 and BAFF 02 Gel additives are added to concrete, the chemical salts of the complex salts that make up the additive react with the calcium, aluminum and iron ions present in the concrete (concrete product) to form supersaturated solutions of insoluble complexes. In the process of concrete curing, insoluble complexes in the form of needle-shaped crystals crystallize from supersaturated solutions in the form of pores in the concrete body. Strength indicators of concrete increase. During the operation of concrete, needle crystals prevent the diffusion of water droplets through pores and microcracks (up to 0.4 mm) inside the concrete body, thereby improving the concrete's waterproof and frost resistance characteristics. Needle-shaped crystals allow excess moisture to freely exit the concrete body in the form of water molecules (the vapor permeability of concrete is preserved).

Waterproofing is intended: 1. To increase the indicators of water resistance, frost resistance, concrete strength on old and newly built concrete and reinforced concrete structures. It is applied on a concrete surface. 2. Protects the concrete structure from the effects of wastewater and groundwater, sea water, oil products, aggressive environments: acids, alkalis, etc. 3. Increases the corrosion resistance of concrete, prevents corrosion of steel reinforcement. 4. The penetration depth of functional additives in 60 days ≈ 0.5 m. (The speed of movement within the body of the model concrete composition is 2 ∙ 10-6 m / s at a depth of 0.1 m), therefore, partial destruction of the concrete body, with the condition that its integrity will not be able to violate the waterproofing of the concrete structure. Operating principle: The composition "BAFF.01" is applied to the internal or external surfaces of the concrete structure, regardless of the side of the influence of liquid media on the concrete object. After applying the composition, water-soluble functional additives in the form of a solution penetrate into the pores deep into wet concrete, interact with calcium and aluminum oxides, forming insoluble needle crystalline hydrates that fill capillaries, microcracks and concrete pores, which prevent water from entering the concrete body. The concrete structure becomes waterproof, the ability of water molecules to pass through the formed barriers from insoluble complex needle crystals leaves such a property as vapor permeability behind concrete. The rate of formation of insoluble crystalline hydrates filling the pores of the concrete body depends on factors such as moisture, porosity, and temperature of the concrete. After the concrete body has dried, unreacted water-soluble functional additives crystallize and remain in the pores of the concrete. In cases of localization of a new source of liquid pressure, water-soluble additives are able to re-enter the saturated saline solution and form needle-like insoluble crystalline structures, imparting a property to concrete such as self-healing Mixture preparation: 1. The dry mixture of the composition "BAFF 01" is mixed with water in a ratio of 3/1 to obtain a creamy consistency. The survivability of the composition is 20-30 minutes. 2. Apply by brush or trowel to a damp concrete surface. 3. On horizontal surfaces in one layer, on vertical surfaces it is necessary to apply 2 layers., With an interval of 2 hours. 4. The consumption of the composition "BAFF 01" 0.8-1.3 kg / m2. 4. Use in 30 minutes, stirring regularly without adding water.