Other equipments and machines in bulk on Qoovee

Magnetic grippers are cheaper than Chinese ones! In stock! Delivery!

CO2 SCRUBERS Any fruit and vegetable products breathe during storage. This is the process during which oxygen is converted to carbon dioxide. Excessive levels of carbon dioxide in the atmosphere of the refrigerator compartment surrounding the stored product can damage it. Therefore, excess carbon dioxide must be removed. One possible way to remove carbon dioxide is by using a CO2 adsorber. A CO2 adsorber is a device that removes carbon dioxide and some ethylene from refrigeration chambers. The CO2 adsorber contains activated carbon, which binds the carbon dioxide molecules when the air from the storage chamber is passed through the adsorber. In addition to the control panel, with the help of which the operating parameters for all refrigerating chambers are programmed, the adsorption device is equipped with a system that does not allow the ingress of oxygen in the air into the chambers during some cycles of the CO2 scrubber. Adjusting the speed of the low-pressure fan helps to reduce the energy consumption of the system, which is an important advantage, since the adsorber can work most of the day. Considering that the respiration rate of different fruit and vegetable products is not the same and the storage volumes at different sites are individual, CO2 adsorbers are produced with different capacities, which allows meeting the needs of all customers.

OXYGEN GENERATOR PSA INDUSTRIAL Oxygen generators "MAS Systems" with PSA technology - short-cycle heatless adsorption. The use of air-separating adsorption oxygen plants can reduce the cost of oxygen produced by several times. Apart from the economic benefits, the undoubted advantage of these systems is their simplicity in operation and maintenance, as well as very high reliability. PSA oxygen generators separate oxygen (O2) from air using pressure swing adsorption technology. Atmospheric air, which consists of approximately 21% oxygen and 78% nitrogen, is passed through a bed of zeolite molecular sieve (CMS) at a specific pressure. The sieve adsorbs N2 and other gases, allowing oxygen to pass through it as a product gas. While one of the columns is in the adsorption phase, the other is regenerated by depressurization, the sieve releases the adsorbed gases into the atmosphere, and the cycle repeats. The programmable controller controls process valves on an alternating cycle with built-in logic for automatic stop / start. Oxygen flow and purity remain the same regardless of peak loads. Under normal operating conditions and with proper care, the zeolite molecular sieve will have a long service life.

MEMBRANE NITROGEN GENERATORS Membrane nitrogen generators are gas separation systems that allow the production of gaseous nitrogen up to 5,000 m³ / h from atmospheric air. Membrane nitrogen generators are fully automated systems designed for indoor use or as part of a mobile station in an open space. The release of nitrogen occurs due to the difference in the rate of penetration of gas components through the membrane substance. The purity of the nitrogen obtained is up to 99.5%. Membrane nitrogen generator MAS-GN2-M. The use of the latest technologies, high-quality components from the world's leading manufacturers, a modern intelligent control system ensures the exceptional reliability of the membrane nitrogen generator, guaranteed obtaining the specified technical parameters and ease of use. The MAS Systems company is ready to offer you the development of an individual project and carry out the production of membrane systems with the given technical characteristics.

MAS Systems nitrogen generators operating on the principle of adsorption air separation are designed to produce up to 5000 Nm³ / h of nitrogen. The maximum nitrogen purity is 99.9995%. Nitrogen generators and nitrogen plants can be designed for both indoor and outdoor use. Nitrogen generators manufactured by MAS Systems are used in food, pharmaceutical, chemical, metalworking, gas and oil production plants, in nitrogen fire extinguishing systems and other industries.

The high accuracy and small dimensions of the Prince-M G25 utility gas meter allows the device to be used as part of a commercial gas metering unit, in production and utilities. Each counter is equipped with a thermocorrector, it is possible to configure additional parameters. The meter operates at temperatures of the measured medium in the range from -40 to +60 ° С. Can be installed outdoors in unheated rooms, in harsh weather conditions. The design of the meter does not contain moving parts, which increases reliability, no additional maintenance is required. The meter is powered by a built-in battery designed for 10 years of operation. For the convenience of data retrieval, it is possible to organize a remote transmission system in various ways, integration with many gas suppliers.

Meters are installed in boiler rooms of production facilities, entrances of apartment buildings and at other facilities where a reliable accurate gas meter is required and space for installing additional equipment is limited. The operating temperature range is from -40 to +60 ° C, which guarantees accurate measurements even in the most severe conditions. The possibility of installation in unheated rooms and outdoors makes the gas meter unique in the utility segment, and the ready-to-use telemetry system allows you to control many meters by one operator. All devices are equipped with a temperature sensor located directly in the gas flow, which, according to the certified measurement procedure, makes it possible to bring the accumulated volume values to standard temperature conditions, it is possible to adjust the compressibility coefficient and set the pressure constant. The calibration interval and the manufacturer's warranty is 6 years, during which the company makes a replacement in case of a defect.

We are a China hot melt glue machine manufacturer and have been engaged in hot melt glue machine for more than 5 years. Our company supplies various parts for hot melt glue machines, including their spray guns, modules, wire kits, heaters and solenoid valves, etc. We can provide food, pharmaceuticals, beverages, cosmetics and woven fabrics, non-food consumer goods, seeds, cables, book bindings and more. We can provide solutions for cartons, labels, liner nozzles, pallet forming, straws, etc. The hot melt glue machine is widely used in sanitary products such as diapers, sanitary napkins and other hygiene items, and in the production of air filters, non-woven composite materials. , footwear, printing industry, product assembly, clothing, stickers, packaging industry (cartons, cigarette cases, gift boxes, glasses boxes, craft boxes, jewelry boxes, colored boxes, composite covering (label paper, labels, double-sided tape , medical breathable tape), products (household appliances, furniture fittings, wires and cables)

Features of explosion-proof pneumatic industrial vacuum cleaner Dastprom PP-EX / 60.2: Compressed air operation. No power connection required; A compressor is required for operation; Has a large stainless steel tank for collecting 60 liters of dirt and a sturdy metal frame; The vacuum cleaner is equipped with two noise suppression filters and a HEPA fine filter; The cleaning efficiency reaches 0.3% micron, 99.99%; Use of anti-static hose with long and short connecting valves eliminates sparking with explosion-proof function;Purpose: Cleaning of explosive dust and waste; Dry and wet cleaning; Cleaning of metal shavings, parts, as well as metal chips when cutting and polishing metal; Collection of chemical and toxic liquids and oils; Cleaning of plastic parts when processing plastics; Cleaning of textile waste from natural and synthetic raw materials: wool, cotton, linen, silk, artificial and synthetic fibers, synthetic threads; Fine dust removal, work with a grinding machine; Purification of carbon powder, oil, chemical powder, powder coating, white titanium powder, magnetic powder, etc;Wide application in various industries: military-industrial complex, pharmaceuticals, medicine, mechanical engineering, metalworking, woodworking, food processing, textiles, shipbuilding, metallurgy, painting workshop, construction, oil refineries, chemical and other industries. The standard delivery set includes: Vacuum cleaner - 1 pc. Hose (high quality fully antistatic hose; inner diameter 38 mm, outer diameter 42 mm, length 2.5 m) - 1 pc; Steel pipe-rod (antistatic design, composite; length 1 m) - 1 piece; Double HEPA filter - 1 piece; Noise reduction filter - 2 pcs; Replacement nozzles: sex nozzle with bristles, sex nozzle with rubber inserts, crevice nozzle, round nozzle with bristles. Characteristics Country of Origin China Guarantee 12 months for a vacuum cleaner Waste collection tank 60 l Air flow at the inlet to the vacuum cleaner 280 m³ / hour Air purification efficiency 99.9%, 0.3 μm Working hours continuous, round the clock Housing stainless steel Length 650 mm Width 600 mm Height 1120 mm Weight 43 kg Package weight 48 kg Packaged length 745 mm Packing Width 635 mm Height in packing 1150 mm Noise level not more than 53 dB Filter material area 22680 cm² IP protection class IP66 Power cable length 8 m Maximum suction power 230 Mbar

Our smallest industrial vacuum cleaner with a 15 liter tank. Features of the Dastprom PP-220 / 15.1-1.5 model: The vacuum cleaner is equipped with two successive cyclones. This allows it to "store" any dirt in the tank and extend the life of the filters. Replaceable bags and other consumables are not required during operation; The electric power of the turbine is 1500 W. Its suction power is sufficient for using the vacuum cleaner when cleaning any non-explosive dirt and any non-flammable liquids; The vacuum cleaner is equipped with a soft start system; The vacuum cleaner has a socket for connecting a power tool with a power consumption of 50 to 2000 W; The vacuum cleaner can be used for blowing off. For this, the hose is connected to the working air outlet; Supplied with a set of 2 pieces of washable, reusable ultrafine HEPA filters with a filtration area of more than 1.7 m²; Dimensions and weight make it easy to transport in any car; For ease of transportation, the vacuum cleaner is equipped with a removable platform with non-marking wheels. The standard delivery set includes: A vacuum cleaner; Vacuum cleaner nozzle 360 mm; Water collecting rubber for 360 mm nozzle, set (2 pcs); Universal slotted vacuum cleaner nozzle; Round lint for vacuum cleaner; Vacuum cleaner bar ; Vacuum cleaner hose (standard, 3 m); Filtering elements ( a set of ultrafine filters and a turbine cooling filter ). Characteristics Country of Origin Russia Guarantee 12 months for a vacuum cleaner, 6 months for a turbine Electric power 1.5 kW Waste collection tank 15 l Power supply voltage 220 V Air flow at the inlet to the vacuum cleaner 208.2 m³ / hour | 57.8 l / s Maximum vacuum up to 32 kPa Air purification efficiency 99.9% Number of filters 2 Housing steel Coating polymer, powder coating Length 442 mm Width 442 mm Height 866 mm Weight 21.8 kg Diameter of the body (cyclone) 345 mm Package weight 26.8 kg Package volume 0.19 m³ Packaged length 450 mm Packing Width 450 mm Height in packing 885 mm Noise level no more than 65 dB IP protection class IP32 Power cable length 5 m Mean time to failure of turbines (replacement of brushes) not less than 500 hours Operating temperature range -50 ° C to +55 ° C Maximum suction power 550 aerowatt

Pump membrane dosing units NDR-2M are designed for volumetric pressure dosing of neutral and aggressive liquids, emulsions and suspensions. The scope of application of the membrane dosing unit is determined by the resistance of the materials of the flow path in the dosing medium and the design of the electrical equipment. The diaphragm pumping dosing unit NDR-2M can be used for dosing harmful substances, flammable and combustible liquids, provided that safety rules are observed. To increase reliability, the diaphragm metering pump NDR-2M is equipped with a two - layer membrane made   from treated PTFE . 8 advantages of the diaphragm dosing pump NDR-2M: 1. Tightness. During operation of the NDR-2M pump, leakage of the pumped and working fluid is completely excluded. 2. Possibility of regulation without stopping the pump.   The design of the NDR-2M pump provides for flow adjustment during pump operation.   3. Simplicity of operation and maintenance.   In the pump NDR-2M   there is no need to constantly monitor and maintain   plunger seal as is the case with LP plunger pumps. 4. Wear-resistant valve. The diaphragm pump valves are specially designed for long-term operation in contact with aggressive media. Their service life is much longer than that of conventional   pumps LP. 5. Ability to operate the pump at high pressures up to 100 MPa. Many diaphragm pump manufacturers cannot achieve this. 6. Membrane condition monitoring system. If the diaphragm is damaged, the monitoring system will report this. Even in the event of a diaphragm rupture, the pump remains operational until the end of the process. The signaling device can be both a pressure gauge and electronic devices that will report the problem to the control station. 7. Safety system In the event of a blockage in the outlet piping due to faults or errors, a built-in valve will protect the pump from overload.             8. Saving money Favorable price level achieved through our own production   Technical characteristics of the diaphragm pump NDR-2M 40/400: Feed-40 l / hour The pressure at the outlet of the pump is 400 kgf / cm2; Electric motor power - 3 kW 1500 rpm. Factory warranty - 1 year!

Vertical steel tanks - designed for receiving, storing, dispensing oil products and water, as well as other liquids, in various climatic conditions

Oil and gas separator oil and gas equipment that is used for degassing non-foamy oil during the extraction process and removing associated gas from it.

The travel heater is designed for heating oil products, oil emulsions, viscous oil during transportation through pipelines, at oil fields and oil treatment plants.

Sump is a storage tank used to collect liquids, as well as for their primary mechanical cleaning. Sediment tanks are used both on an industrial scale and in individual farms. At the stage of primary treatment, when sedimentation tanks are mainly used, mechanical impurities and suspended substances are extracted from the liquid under the action of gravitational forces, and biological treatment processes begin; when using the settler as a biocoagulator, fine and colloidal impurities are deposited, and sorption processes occur on the sludge particles. Oil sump is a special equipment designed to separate oil-water emulsion. In the separation process, oil is obtained, which is then collected, and formation water, which is discharged. Mechanical impurities and salts are removed from the raw material together with formation waters. Some oil settler designs also allow the removal of dissolved gas.

ND plunger metering pumps are designed for volumetric pressure metering of neutral and aggressive liquids, emulsions and suspensions. The area of application of pumps is determined by the resistance of the material of which the hydraulic part is made, as well as the resistance of the seal material.   LP metering pumps are positive displacement pumps. By the form of movement of the working bodies - reciprocating.   Pumps of the ND series are single-plunger (double-plunger), horizontal, single-acting, with a manually adjustable flow when the electric motor is stopped. Flow rate-100 l / h The pressure at the outlet of the pump is 250 kgf / cm 2 Order European quality at Ukrainian prices!

The scope of application of the membrane dosing unit is determined by the resistance of the materials of the flow path in the dosing medium and the design of the electrical equipment. The diaphragm pumping dosing unit NDR-2M can be used for dosing harmful substances, flammable and combustible liquids, provided that safety rules are observed. To increase reliability, the diaphragm metering pump NDR-2M is equipped with a double - layer diaphragm made of treated PTFE . Advantages of the diaphragm dosing pump NDR-2M 1. Tightness. During operation of the NDR-2M pump, leakage of the pumped and working fluid is completely excluded. 2. Possibility of regulation without stopping the pump. The design of the NDR-2M pump provides for flow adjustment during pump operation. 3. Simplicity of operation and maintenance.   In the NDR-2M pump, there is no need to constantly monitor the plunger seal and maintain this seal, as is done when using ND plunger pumps. 4. Wear-resistant valve. The diaphragm pump valves are specially designed for long-term operation in contact with aggressive media. Their service life is significantly longer than that of conventional LP pumps. 5. Ability to operate the pump at high pressures up to 100 MPa. Many diaphragm pump manufacturers cannot achieve this. 6. Membrane condition monitoring system. If the diaphragm is damaged, the monitoring system will report this. Even in the event of a diaphragm rupture, the pump remains operational until the end of the process. The signaling device can be both a pressure gauge and electronic devices that will report the problem to the control station. 7. Safety system In the event of a blockage in the outlet piping due to faults or errors, a built-in valve will protect the pump from overload. 8. Saving money Favorable price level achieved through our own production Technical specifications: Feed - 1000 (l / h) The pressure at the pump outlet is 25 kgf / cm 2 European quality - Ukrainian price!          

Internal circulation fans transport moisture. Needs instant computer control. It should be able to be automatically controlled with. The circulating fan will be used throughout the entire greenhouse. Material: Stainless steel housing, wires and casing Metal 0.35 kWh : 1400 rpm Air flow: 5,700 m 3 / h Equipment: hanging chains and link Certificate: CE Standards

Marine air compressors and installations are used on ships: - to launch the main diesel installation; - to provide facilities with high-pressure compressed air; - filling with air and maintaining pressure in ship air guards; - refueling cylinders of breathing apparatus.

ENERGOSERVICE-M LLC is a leading Ukrainian enterprise in the supply of industrial refrigeration equipment with highly qualified engineering and production personnel and modern technological equipment. ENERGOSERVICE-M LLC - is a supplier of crane and autonomous air conditioners to ensure the safe operation of technological equipment, maintain the required temperature and humidity, clean it from harmful impurities: Autonomous industrial air conditioners: KA1-25 (KA2-25), KA1-40 ( KA2-40), KSA-15 (2KSA-15), KSA-20 (2KSA-20), KSA-25 (2KSA-25), KSA-45 (2KSA-45), 1KSA-15 (3KSA-15), 1KSA-20 (3KSA-20), 1KSA-25 (3KSA-25), 1KSA-45 (3KSA-45), KSA6.5 / 25 (1KSA6.5 / 25), KSA-3/15 (1KSA-3 / 15) are installed in industrial and office premises: 1) Control panels (posts) on rolling mills ( CA-15, KSA-20, KSA-25); 2) Control panels in the heat-power workshop (KSA-15, KSA-20); 3) Mashrooms (KSA-25, KSA-45); 4) Electrical facilities (microprocessor, thyristor, local telephone exchanges); 5) Laboratories (chemical, quantometric); 6) Service premises (conference rooms, canteens, change houses).

Rotary compressors and gas blowers are used in aeration systems of fish ponds, potable water storage tanks as well as aeration systems in the sludge pools of treatment facilities, when spraying gardens and crops, in foundries. Aeration is a process of forced saturation of water with air, or oxygen. To ensure this process, a low-pressure compressor or blowers for aeration are used, and its purpose is: Aeration is the process of forced saturation of water with air, or oxygen. To ensure this process, a low-pressure compressor or aeration blowers are used, and its purpose is: Oxidation of iron compounds (water deferrization) and manganese, which consists in the oxidation of iron and manganese compounds with oxygen. As a result, these compounds precipitate in the form of flakes, which are retained by a special filling sediment filter. Removal of dissolved gases, including toxic ones, for example, hydrogen sulfide and methane. Disinfection of water as a result of the destruction of organic substances contained in it, under the influence of oxygen. Removing bio-pollution: when oxygen is saturated with water, the number of beneficial aerobic bacteria that process biomass into carbon dioxide and methane-biogas increases. Now the bio-treatment process is used at all large treatment facilities in Russia. The resulting biogas can also be pumped out of the tanks of treatment plants using blowers for further use, for example, for the production of electricity or fuel for vehicles. However, in Russia this practice is not yet common. Maintaining the pond ecosystem by saturating the water with oxygen. In stagnant water under the influence of sunlight, anaerobic bacteria begin to multiply actively. As a result, the reservoir turns into a muddy swamp with an unpleasant odor. Also, due to insufficient oxygen concentration in the water, pestilence of fish and other beneficial organisms occurs.

Air compressors 4VU1-5 / 9 series are used to provide compressed air to pneumatic tools, devices, mechanisms; work in pneumatic transportation systems for bulk solids (sand, cement, grain, etc.). Are applied: · at machine-building enterprises; · As part of oil and gas rigs; · At the facilities of the petrochemical, gas, metallurgical, electrochemical, mining and other industries. Piston compressors, V-formed, four-cylinder, two-stage. Drive from an electric motor through an elastic coupling. Forced lubrication. Air cooling of cylinders and refrigerator. Condensate discharge and discharge are automatic. Compressors 4VU1-5 / 9 are equipped with an automatic control and protection system, which provides: · automatic maintenance of pressure in the receiver within specified limits by starting and stopping the compressor, as well as bypassing the air from the discharge to the suction; · Unloading and purging of the compressor when it is stopped; · Electric oil heating in the crankcase (for the northern version); · The ability to purge and unload the compressor from the control panel in manual mode; · Emergency stop during overheating of compressed air; · Emergency stop when the pressure in the lubrication system is below the permissible value. Compressors with relay or microprocessor automation are available. 4VU1-5 / 9 air compressor series are manufactured in the following modifications: 4VU1-5 / 9 M1 compressor 4VU1-5 / 9 M2 compressor 4VU1-5 / 9 M3 compressor (without electric motor and frame) 4VU1-5 / 9 M4 compressor 4VU1- compressor 5/9 M6 (without electric motor, refrigerator, frame, control panel and pressure gauge shield) 4VU1-5 / 9 M7 compressor with electric oil heating (without electric motor and frame) 4VU1-5 / 9 M8 compressor with electric oil heating 4VU1-5 / 9 compressor M32 (without electric motor and frame) Compressor 4VU1-5 / 9 M42

Stand-alone air conditioner AKV-4.5 with air-cooled condenser, designed for cooling, heating and purifying air in industrial premises, control rooms, equipment rooms, electrical halls, office rooms, at ambient temperatures up to + 45 ° C. Provides maintaining the required air temperature in the range from 12 ° C to 28 ° C, with an accuracy of ± 1 ° C. The air conditioner is equipped with compressors and components of the world's leading manufacturers in the field of refrigeration - Copeland, Danfoss, Bristol. NAME OF PARAMETERS \ MODEL AUTONOMOUS AIR-CONDITIONER AKV-4,5 Productivity on cold, kW 21,0 Productivity on heat, kW 12,0 Nominal air consumption, m3 / h 4500 External static pressure, Pa 300 Degree of air purification,% 90 Refrigerant R -22 Power supply 380 V / 3ph / 50 Hz Power consumption (in cooling mode), kW 8.9 Evaporator type Copper tubes with aluminum fins Condenser type Copper tubes with aluminum fins TRV refrigerant flow regulator TRV refrigerant flow regulator Fan (centrifugal with double external suction): drive: belt; power: 1,5 kW. Overall dimensions (length x width x height), mm: air handling unit: 520 x 1200 x 1800; condenser unit: 650 x 1500 x 850. Weight, kg: air handling unit: 265; capacitor block: 110.

Compressor FV6. It has an external drive and operates in 3 modes. The first uses R-12 freon. The device is capable of achieving 7.5 kW of cooling capacity, while consuming no more than 2.5 kW of energy. The second mode also includes operation on R-12 freon, but the compressor produces up to 5.35 kW, spending 1.7 kW of energy. The third mode is activated when refueling with R-22. This makes it possible to generate 11.05 kW of cooling capacity, using 4.2 kW of electricity. The FV6 compressor is one of the main elements of the refrigeration unit and serves to carry out a continuous refrigeration cycle by constantly aspirating the refrigerant vapor from the evaporator and compressing them to condensation pressure. Designed to work as part of automated stationary and transport refrigeration units and air conditioners. NAME OF PARAMETERS \ MODEL REFRIGERATING COMPRESSOR ФВ6 Compressor type Freon compressor, piston, vertical, single-stage, cross-axle with external drive. MODE 1 Cooling capacity, kW (kcal / h) 7.5 (6500) Effective power, kW 2.5 Volume described by pistons, m3 / h 31.0 Cooling capacity and effective power are indicated in the mode, ° С during operation on R-12 on the mode: boiling point minus 15 ° С; condensation temperature 30 ° C; suction vapor temperature 15 ° C; shaft rotation speed 24 s-1 (1440) (rpm). MODE 2 Cooling capacity, kW (kcal / h) 5.35 (4600) Power consumption, kW 1.7 Volume described by pistons, m3 / h 20.7 Cooling capacity and effective power are indicated in the mode, ° С during operation on R-12 on the mode: boiling point minus 15 ° С; condensation temperature 30 ° C; suction vapor temperature 15 ° C; shaft rotation speed 16 s-1 (960) (rpm). MODE 3 Cooling capacity, kW (kcal / h) 11.05 (9600) Power consumption, kW 4.2 Volume described by pistons, m3 / h 31.0 Cooling capacity and effective power are specified in the mode, ° С during operation on R-22 on the mode: boiling point minus 15 ° С; condensation temperature 30 ° C; suction vapor temperature 15 ° C; shaft rotation speed 24 s-1 (1440) (rpm). Cylinder diameter, mm 67.5 Piston stroke, mm 50 Number of cylinders, pcs 2 Refrigerant R12 or R22 Brand of used oil ХФ12-16 (for R-12) or ХФ22с-16 (for R-22) Amount of refilled oil, kg 1 , 7 ± 5% Weight, kg 50 Overall dimensions (length x width x height), mm 368 x 324 x 392

A heat pump is a machine that can transfer heat from a colder environment (air, earth, solar radiation, water from underground strata, water from open reservoirs, water from a common network, heat recovery, industrial waste water) to a hotter one (air, water and other). Under some conditions, a heat pump with a compressor having a 1 kW electric motor as a drive can provide a heat power of 3 to 5 kW, although it is known that the simple heat generation on a resistance with an electric power of 1 kW cannot exceed 1 kW. INSTALLATION APPLIED COMPRESSOR REFRIGERANT OVERALL DIMENSIONS, MM WEIGHT (NET), KG ТХУ6-4-0 “water-water” 5PB10-4-0 R142 1730х500х760 350 ТХУ-14 “water-water” 5ПБ10-2-024 R22 unit 1800х57014 780х570х2000 installation of 620 block of tanks 65 ТХУ24-4-0 "water-water" 5PB50-4-0 R142 2275х620х1010 840 НКТ5-4-9 "water-water" 5ПБ10-4-0 R142 2320х520х1130 560 НКТ10-4-9 "water- water "5PB20-4-0 R142 2285x560x1200 670

The compressor 2FVBS4 / II OM4 is one of the main elements of the refrigeration unit and is used to carry out a continuous refrigeration cycle by constantly aspirating the refrigerant vapor from the evaporator and compressing them to a condensing pressure. Designed to work as part of automated ship refrigeration units and air conditioners. NAME OF PARAMETERS \ MODEL REFRIGERATING COMPRESSOR 2FVBS4 / II OM4 Compressor type freon compressor vertical, piston, single-stage, bezreztskopfny glandless. Cooling capacity, kW (kcal / h) 5.2 (4500) Power consumption, kW 2.2 Volume described by pistons, m3 / h 20.6 Cooling capacity and effective power are indicated in the mode, ° C when working on R-12 in the mode: boiling point minus 15 ° С, condensation temperature 30 ° С, suction vapor temperature 20 ° С liquid temperature in front of the throttle device 25 ° С Type of built-in electric motor АПВ2-41-6Ф Electric motor power, kW 2,1 Supply voltage, V 380 Rod alternating current, 3-phase Current frequency, Hz 50 Diameter of cylinder, mm 67.5 mm Ho d piston, mm 50 mm Number of cylinders, pcs 2 Synchronous speed, s-1 (r / min) 16.7 (1000) Volume described by pistons, m3 / h 20.6 Refrigerant R-12 Brand of used oil ХФ12- 16 Amount of refilled oil, kg 2.5 ± 5% Weight (dry) of the compressor, kg 130 Overall dimensions (length x width x height), mm 595 x 370 x 455

COMPRESSOR HIGH PRESSURE UNITS of the EKPA-2/150 series are intended for forcing air into cylinders and automatically maintaining pressure in them within 150 kgf / cm2 or 200 kgf / cm2. Used: · to start diesel-electric units; · For filling cylinders of breathing apparatus. The installation consists of a compressor and an electric motor. The compressor is three-stage. Circulating pressure lubrication from gear pump. Cooling - with seawater from a vortex type pump. Installation management is automatic. Installations are made in tropical marine execution. At the request of the customer can be made in marine export or marine tropical designs. The automatic control and protection system provides: - automatic start-up of the installation at a system pressure of less than 80 kgf / cm2; - automatic stop at a pressure in the system of 150 or 200 kgf / cm2; - emergency stop when the oil pressure in the lubrication system is reduced to 0.5 kgf / cm2; - emergency stop when the air temperature rises after the refrigerator of the first stage to 60 ° C; - Alarms on the automatic control panel for each emergency stop.

Crane air conditioners of the KK series with air-cooled condenser are designed to create a comfortable air temperature in the cabins of bridge electric, gantry cranes, and other industrial premises, ensuring the maintenance of the required temperature. The temperature control range is from + 12 ° С to + 30 ° С with an accuracy of ± 0.5 ° С, at an ambient temperature from -25 ° С to + 65 ° С on ozone-safe freon R-134a, and up to + 80 ° С on R-142 freon or ozone-safe freon. R-227 Used in coke, ferroalloy and metallurgical industries. Air conditioners are equipped with hermetic or semi-hermetic compressors of the world's leading manufacturers - Copeland, BOCK, and fans - EBM Papst, ZIEHL-ABEGG made in Germany. Air conditioning is controlled by a control panel, which includes a programmable controller. Air conditioners work from sources of alternating current 380V and direct current 220V. Additionally, air conditioners are equipped with an air heater.

NAME OF PARAMETERS \ MODEL AIR COMPRESSOR 4VU1-5 / 9M32 Final overpressure, kgf / cm2 8 Productivity, m3 / min according to the suction conditions: 5 compressed air: 0.56 Engine power, kW - Crankshaft rotational speed, rpm 735 Weight , kg 750 Overall dimensions, mm 1110 x 960 x 1110 Oil heating in the crankcase -

Designed for pumping air through gas purification units of nuclear power plants, transporting explosion-proof, toxic gases that do not contain droplet liquid and mechanical impurities. The gas blower is a rotational compressor machine made of stainless steel, driven by an electric motor through an elastic coupling. The gas blower can be operated at a suction gas temperature of -10 ° C to + 40 ° C. NAME OF PARAMETERS \ MODEL GAS BLOWING ROTARY E21-50-4A Max. pressure difference, kPa, mode 50 Productivity, m3 / min 1.44 Power of electric motor, kW 4.0 Weight, kg 240 Overall dimensions (length x width x height), mm 1085 x 520 x 510

Designed for the transport of air, toxic and aggressive to oil gases, non-corrosive to cast iron and structural steel, explosion-proof in the flow part and not containing droplet liquid and mechanical impurities. The gas blower is supplied driven by an electric motor through an elastic coupling. Delivery options with an explosion-proof or general industrial electric motor are possible. The gas blower can be operated in pressure or vacuum modes at an ambient temperature of -10 ° C to + 35 ° C. NAME OF PARAMETERS \ MODEL GAS BLOWING ROTARY 1G21-30-2V Max. pressure difference, kPa, pressure mode: 30 vacuum: 30 Productivity, m3 / min 4.32 Power of electric motor, kW 4.0 Weight, kg 285 Overall dimensions (length x width x height), mm 1050 x 450 x 545

Rotary compressor 12VF-M-30-0.6-1.5-2.2 VF compressors: 2VF, 12VF, 32VF and 34VF are designed for transporting air and gases non-corrosive to cast iron, structural steel and mineral oil. VF rotary compressors, compressors 2VF-M-70-21,5-1,5-45, 12VF-M-20-0,69-1,5-2,2, 32VF-M-60-22,1-1 5-45, 32VF-M-80-21.0-1.5-45 (32VF-21 / 1.8SM2U3), 34VF-M-30-38.2-1.5-45, 34VF-M- 40-37.4-1.5-45, 34VF-M-50-36.6-1.5-45 (34VF-37 / 1.5SM4U3) are used: in pneumatic transportation systems for bulk materials, air mail containers; in aeration systems of the sludge pools of treatment facilities, drinking water storage tanks, fish ponds; when spraying crops and gardens; during fire fighting; when removing dust in printing houses, foundries, filter plants; for driving various devices and mechanisms (grips, clamps). Compressor stations 2VF, 12VF, 32VF and 34VF are supplied with vertical and horizontal air flow direction. Compressors 2VF, 12VF, 32VF and 34VF consist of a compressor unit, a check valve, an electric motor, silencers and a noise-attenuating casing. Compressors operate in pressure and vacuum modes. Compressors rotary VF series are issued instead of earlier made compressors of grades 1A, 2AF.

Designed to supply air, not containing droplet liquid and mechanical impurities, into the pneumatic system for transporting grain, products of its grinding and other bulk solids. It is applied: at combines of bakery products; in mills, elevators; in feed mills. The compressor can be operated in explosive rooms with a dangerous concentration of dust at an ambient temperature ranging from -10 ° C to + 35 ° C. The compressor consists of a compressor unit, a safety valve and an electric motor located on a common base, which is also a silencer. NAME OF PARAMETERS \ MODEL COMPRESSOR GEAR 3AF49K52С Pressure difference, kPa 40 Productivity, m3 / min 1,54 Power el. engine, kW 2.2 Weight, kg 253 Overall dimensions (length x width x height), mm 1360 x 450 x 780

The Agromash Inter company offers pvc gate with a diameter from 40 mm to 160 mm. Gate valves are designed for installation as shutoff valves in various enterprises. They are a shutter made in the form of a sharpened plate. Due to the shape of the gate, on the one hand, the flow of liquids is completely blocked, and on the other, inclusions that may be contained in them are suppressed. The main task of the gates: shutting off the flow of working fluids in pipelines. Production material - PVC (PVC-U). Available gates of the following diameters: DN40, DN50, DN63, DN75, DN90, DN110, DN160. Contact person: Nikolay Aleksandrovich LLC Agromash inter

The Agromash Inter company offers washing nozzles with a diameter of 20 mm, 25 mm and 32 mm for a nozzle. Nozzles are designed for installation in a mechanical drum filter. Water supplied to the nozzle under a pressure of 2-4 atm. carries out cleaning of the filter mesh of the drum filter from adhering dirt, residues of feed, scales and other mechanical impurities. The nozzle is made of polymer materials resistant to aggressive environments. Thanks to the original design, it is easily disassembled for maintenance and installed on the pipeline. Price: 1 000 rubles Contact person: Nikolay Aleksandrovich LLC Agromash inter

The Agromash Inter company offers a flotator of its own production for ultrasonic testing. • Flotator productivity: from 25 m3 per hour to 100 m3 per hour • The main task of the flotator • Removal of fine particles • Removal of organic residue Scope • Fish farms of ultrasonic testing • Owl Complete set • Stand • Aeration system • Compressor • Pump • Control cabinet Contact person: Nikolay Aleksandrovich LLC Agromash inter

The Agromash Inter company offers a sorting box for fry of own production. The sorting box for fry is intended for sorting fry • carp • trout • pike perch • clari catfish • tilapia • sturgeon • other types of fish Technical characteristics • the sorting box is made of polypropylene • has a wall thickness of at least 8 mm • Adjustable clearance from 1 to 20 mm Overall dimensions • Length - 320mm • Width - 387mm • Height - 220mm Price: 6,000 rubles Contact person: Nikolay Aleksandrovich LLC Agromash inter

The company "Agromash inter" offers a ready-made engineering solution for fish farming in the UZV, with a capacity of 2 tons of finished products per year. High-quality equipment and modern water treatment technologies accompany the creation of a favorable environment for intensive breeding of high-quality fish products. The ultrasound module is supplied in the form of a kit that includes technological equipment, pipelines, electrical accessories. The kit includes technical information for the installation of equipment. If necessary, we carry out installation supervision. Price: 2,200,000 Contact person: Nikolay Aleksandrovich LLC Agromash inter

The company "Agromash inter" offers a ready-made engineering solution for fish farming in the UZV, with a capacity of 1 ton of finished products per year. High-quality equipment and modern water treatment technologies accompany the creation of a favorable environment for intensive breeding of high-quality fish products. The ultrasound module is supplied in the form of a kit that includes technological equipment, pipelines, electrical accessories. The kit includes technical information for the installation of equipment. If necessary, we carry out installation supervision. Key parameters: • Maximum one-time fish maintenance during rearing - 1200 kg • Maximum one-time fish maintenance during overexposure - up to 2000 kg • Area occupied by module equipment - 36 m2 • Total volume of water in the system - 34 m3 • Volume of fish breeding pools - 23 m3 • Average daily water change (per year) - 6% Price: 1,200,000 Contact person: Nikolay Aleksandrovich LLC Agromash inter

The Agromash Inter company offers trays for fry of own production for your fish farm. Bowls of trays are made of food grade engineering polypropylene. The material is resistant to various influences of hostile environments, such as acid, alkali and saline solutions. It also has resistance to ultraviolet radiation. All bowls are equipped with a protective flange. In addition, trays for larvae can be equipped with a bottom discharge, a pipe for supplying water, a system of saturation of water with oxygen. Our trays can be installed both indoors and outdoors. All products are made of environmentally friendly materials and have appropriate quality certificates. An official manufacturer's warranty is provided for all products! Contact person: Nikolay Aleksandrovich LLC Agromash inter