Construction mixtures in bulk on Qoovee

Purpose: Designed to destroy and prevent the formation of mold, fungi, mosses, lichens on mineral materials (stone, concrete, gypsum, plaster, ceramic tiles, gypsum plasterboards, etc.) and wood (plywood, fiberboard, chipboard, etc.) .). Recommended for processing facades and basements of buildings, fences, rooms with high humidity (basements, cellars, kitchens, bathrooms, greenhouses). It can be added to unmodified plaster, masonry mortars, putty as a biocidal additive instead of mixing water. The tool perfectly sanitizes the surfaces of walls, brickwork, ceilings, interpanel seams. Has a long-lasting effect.   Benefits: long-term protection up to 15 years; effectively protects against biological damage and insects; environmentally friendly, does not contain solvents; does not damage or stain the treated surfaces. as a biocidal additive instead of mixing water.   Mode of application: The product must be diluted with water. Apply an antiseptic with a brush, roller, spray 2-3 times after each previous layer has dried. When treating an already affected surface, apply an antiseptic, after 24 hours clean the surface and repeat the treatment. When processing mineral surfaces directly exposed to water, cover it after drying with a water repellent GKZH-11 or waterproof paints and varnishes. Average consumption 100-150 g / sq. m on mineral grounds and 200-300 gr./sq. m for wood. When used as a biocidal additive in mortar mixtures, test with a small amount for compatibility. Water-borne paint: add 250 ml of paint to 20 liters of paint and mix thoroughly. Additive to plaster: 250 ml of the product is enough for 10 liters of water. Grout or plaster is mixed on the resulting solution. Grout: 50 ml is added to the mixing water per 5 kg of dry mass. Additive to wallpaper glue: add about 25-30 ml of active agent per 1 liter of water to the glue mixing liquid, then prepare the glue according to the instructions. Precautions: When working, use protective equipment for skin, eyes and respiratory organs (rubber gloves, overalls, glasses, respirator). In case of contact with skin, mucous membranes, eyes, rinse immediately with plenty of running water for 10-15 minutes. Seek medical attention if necessary. Danger: Possible irritant effect on the skin. Storage and transportation: Transport and store at temperatures from + 5 ° C to + 40 ° C, in a hermetically sealed original container, separately from food, in a cool ventilated room, out of the reach of children and animals. Avoid heating and direct sunlight. The composition retains its properties after short-term freezing. Dispose of in accordance with SanPin 2.1.7.1322-03Shelf life: 36 months

Fire retardant compound with a powerful antiseptic effect for outdoor and indoor use. It is an aqueous solution of highly effective fire retardants, antiseptics, fungicides and functional additives. Protects wood from fire and the spread of flame indoors for up to 16 years, provides 1 group of fire retardant efficiency in accordance with GOST R 53292-2009 at a consumption of 270 gr. per m², and for up to 30 years from decay, mold, damage by wood-boring insects at a consumption of at least 100 gr. per m². The composition is environmentally friendly. Possibly perform processing to -20 ° C. Does not salt out on the surface. Tones wood in a pleasant amber shade.

Fire retardant compound with a powerful antiseptic effect for outdoor and indoor use. It is an aqueous solution of highly effective fire retardants, antiseptics, fungicides and functional additives. Protects wood from fire and the spread of flame indoors for a period of at least 15 years, provides 1 group of fire retardant efficiency according to GOST R 53292-2009 at a consumption of 275 g / m2, and for up to 25 years from rotting, mold, insect damage woodworms at a consumption of at least 100 g / m². The composition is environmentally friendly, the pH of the composition is 5.5 - 5.7 - which corresponds to the acidity of the skin of an average person and is made from raw materials marked "FOOD" - for food production. Can be processed down to –25 ° C. Does not salt out on the surface and does not tint the wood. After processing with the Kaisar "Premium" composition, any glazing compositions can be applied.

Hydroizol "Haveg" is often used for roof protection. This material is extremely easy to apply, which allows you to quickly process the surface. It is very easy to apply a layer of liquid rubber, and it can be done with various tools. Temperature Stability: Resistance of the waterproofing cover to any temperature: from -50C ° to + 85C ° Durability: The service life of the finished coating is up to 30 years. Absolute UV protection. Impact resistance: The coating is resistant to shock loads both at positive and negative temperatures.   Source and copyright holder:

We are Geoser company from Turkey, a manufacturer of Geosynthetic and waterproofing materials such as HDPE, PVC, LDPE, EPDM and Waterstops. we can provide Geomembrane and Liners in a variety of physical, mechanical, and chemical resistant properties.

We bring to your attention the products of our plant - SoftRock Stone Finishing Coating. It is a water-dispersive polymer coating with a mineral filler and UV inhibitors in its composition. The coating has the following consumer properties and characteristics: · Does not fade; · Possesses high adhesion; · Forms a dense layer on the surface; · Vapor permeable; · Moisture resistant; · Does not create smudges; · Resistant to stretching; · Has high weather resistance; · The surface is covered with a protective film, which prevents the absorption of dust, dirt, etc .; · Simple to use; · Provides high speed of application; · Has a wide range of colors, can be tinted like paint; · Does not deteriorate for more than 25 years. The coating is applied with a texture gun or trowel. The standard consumption is 1.2 kg / m2 on a primed surface, with a layer thickness of 0.8 mm. Stir with a mixer before use! Instructions for applying with a textured (cartridge) pistol: Nozzle 4 mm, mixture supply no more than 30% of the total range of the pistol valve. The compressor is recommended with a receiver from 50 liters. The coating is applied in a circular motion from a distance of 30-40 cm. The mixture is diluted with water in the range of 150-250 ml per 17 kg bucket, no more! Surface preparation: 1. Deep penetration primer. 2. When painting in dark colors, the coating is applied in one layer. 2.1. When painting in light colors, it is recommended to cover the base with acrylic paint of the same color, then apply the stone coating in one layer.

Analogues of famous European and American brands

The additive is intended: 1. To ensure the waterproofing of concrete and reinforced concrete structures. 2.Increases water resistance, frost resistance, concrete strength. 3. Protects the concrete structure from the effects of wastewater and groundwater, sea water, oil products, aggressive environments: acids, alkalis, etc. 4. Increases the corrosion resistance of concrete, prevents corrosion of steel reinforcement. Technical characteristics of "_BAFF 02 Gel": 1. Increasing the water resistance of concrete by at least 3 steps according to GOST 12730.5-84: - for concrete grade B20, increased water resistance from W2 to W8, - for concrete grade B30, increased water resistance from W6 to W14, 2.When increasing the BAFF 02 additive content to 2% of the cement mass in concrete B30, the water resistance index is greater than W14. 3. Increase in frost resistance to 300 cycles in accordance with GOST 26633. 4. The increase in compressive strength according to GOST 10180-90 - not less than 2.5% for concrete B30 - not less than 25% for concrete B20. The mechanism of action of functional chemical additives "BAFF 02": When BAFF 02 and BAFF 02 Gel additives are added to concrete, the chemical salts of the complex salts that make up the additive react with the calcium, aluminum and iron ions present in the concrete (concrete product) to form supersaturated solutions of insoluble complexes. In the process of concrete curing, insoluble complexes in the form of needle-shaped crystals crystallize from supersaturated solutions in the form of pores in the concrete body. Strength indicators of concrete increase. During the operation of concrete, needle crystals prevent the diffusion of water droplets through pores and microcracks (up to 0.4 mm) inside the concrete body, thereby improving the concrete's waterproof and frost resistance characteristics. Needle-shaped crystals allow excess moisture to freely exit the concrete body in the form of water molecules (the vapor permeability of concrete is preserved).

The additive is intended: 1. To ensure the waterproofing of concrete and reinforced concrete structures. 2.Increases water resistance, frost resistance, concrete strength. 3. Protects the concrete structure from the effects of wastewater and groundwater, sea water, oil products, aggressive environments: acids, alkalis, etc. 4. Increases the corrosion resistance of concrete, prevents corrosion of steel reinforcement. Specifications of "_BAFF 02" 1. Increasing the water resistance of concrete by at least 3 steps according to GOST 12730.5-84: - for concrete grade B20, increased water resistance from W2 to W8, - for concrete grade B30, increased water resistance from W6 to W14, 2.When increasing the BAFF 02 additive content to 2% of the cement mass in concrete B30, the water resistance index is greater than W14. 3. Increase in frost resistance to 300 cycles in accordance with GOST 26633. 4. The increase in compressive strength according to GOST 10180-90 - not less than 2.5% for concrete B30 - not less than 25% for concrete B20. The mechanism of action of functional chemical additives "BAFF 02": When BAFF 02 and BAFF 02 Gel additives are added to concrete, the chemical salts of the complex salts that make up the additive react with the calcium, aluminum and iron ions present in the concrete (concrete product) to form supersaturated solutions of insoluble complexes. In the process of concrete curing, insoluble complexes in the form of needle-shaped crystals crystallize from supersaturated solutions in the form of pores in the concrete body. Strength indicators of concrete increase. During the operation of concrete, needle crystals prevent the diffusion of water droplets through pores and microcracks (up to 0.4 mm) inside the concrete body, thereby improving the concrete's waterproof and frost resistance characteristics. Needle-shaped crystals allow excess moisture to freely exit the concrete body in the form of water molecules (the vapor permeability of concrete is preserved).

Waterproofing is intended: 1. To increase the indicators of water resistance, frost resistance, concrete strength on old and newly built concrete and reinforced concrete structures. It is applied on a concrete surface. 2. Protects the concrete structure from the effects of wastewater and groundwater, sea water, oil products, aggressive environments: acids, alkalis, etc. 3. Increases the corrosion resistance of concrete, prevents corrosion of steel reinforcement. 4. The penetration depth of functional additives in 60 days ≈ 0.5 m. (The speed of movement within the body of the model concrete composition is 2 ∙ 10-6 m / s at a depth of 0.1 m), therefore, partial destruction of the concrete body, with the condition that its integrity will not be able to violate the waterproofing of the concrete structure. Operating principle: The composition "BAFF.01" is applied to the internal or external surfaces of the concrete structure, regardless of the side of the influence of liquid media on the concrete object. After applying the composition, water-soluble functional additives in the form of a solution penetrate into the pores deep into wet concrete, interact with calcium and aluminum oxides, forming insoluble needle crystalline hydrates that fill capillaries, microcracks and concrete pores, which prevent water from entering the concrete body. The concrete structure becomes waterproof, the ability of water molecules to pass through the formed barriers from insoluble complex needle crystals leaves such a property as vapor permeability behind concrete. The rate of formation of insoluble crystalline hydrates filling the pores of the concrete body depends on factors such as moisture, porosity, and temperature of the concrete. After the concrete body has dried, unreacted water-soluble functional additives crystallize and remain in the pores of the concrete. In cases of localization of a new source of liquid pressure, water-soluble additives are able to re-enter the saturated saline solution and form needle-like insoluble crystalline structures, imparting a property to concrete such as self-healing Mixture preparation: 1. The dry mixture of the composition "BAFF 01" is mixed with water in a ratio of 3/1 to obtain a creamy consistency. The survivability of the composition is 20-30 minutes. 2. Apply by brush or trowel to a damp concrete surface. 3. On horizontal surfaces in one layer, on vertical surfaces it is necessary to apply 2 layers., With an interval of 2 hours. 4. The consumption of the composition "BAFF 01" 0.8-1.3 kg / m2. 4. Use in 30 minutes, stirring regularly without adding water.

The organization accepts orders from managers of construction sites for the supply of the following types of materials: 1 In Moscow and the Moscow region: Sand, sand salt, technical salt, crushed stone, screening, expanded clay, cold asphalt, peat soil, coal. Delivery in volumes of 20m3, 25m3, 34m3 2 Across Russia: Crushed stone granite, gravel, limestone of all demanded fractions. Delivery by railway transport. 3 In the south of the Moscow region. Limestone crushed stone 20/40, 40/70. Cost - 1350 rubles / m3 with delivery (October 2018) 4 Self-call. Quarry sand. Cost 250 rubles / m3 To calculate the total cost of the order, please indicate the information: Name of the required material Volume of material Requirements for the material (fraction, strength grade, group) Possibility (or lack of possibility) of round-the-clock acceptance of cargo Possibility of travel for Tonars (large-capacity vehicles) Payment form ( cash, bank transfer) Terms (or day) of delivery Delivery address Customer's email Customer's phone number We invite you to contact us by email.

The organization accepts orders from managers of construction sites for the supply of the following types of materials: 1 In Moscow and the Moscow region: Sand, sand salt, technical salt, crushed stone, screening, expanded clay, cold asphalt, peat soil, coal. Delivery in volumes of 20m3, 25m3, 34m3 2 Across Russia: Crushed stone granite, gravel, limestone of all demanded fractions. Delivery by railway transport. 3 In the south of the Moscow region. Limestone crushed stone 20/40, 40/70. Cost - 1350 rubles / m3 with delivery (October 2018) 4 Self-call. Quarry sand. Cost 250 rubles / m3 To calculate the total cost of the order, please indicate the information: Name of the required material Volume of material Requirements for the material (fraction, strength grade, group) Possibility (or lack of possibility) of round-the-clock acceptance of cargo Possibility of travel for Tonars (large-capacity vehicles) Payment form ( cash, bank transfer) Terms (or day) of delivery Delivery address Customer's email Customer's phone number We invite you to contact us by email.

Concrete dye pigment Hormusend HLV-21 is used in concrete solution to add color.   Materials:   garden paths; paving slabs; blind areas around the house; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.

Black concrete pigment Hormusend HLV-21 is used in concrete solution to give color.   The pigment can be colored:   garden paths; paving slabs; blind areas around the house; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.

Concrete dye pigment orange Hormusend HLV-21 is used in concrete mortar to add color.   Materials:   putty; paving slabs; screeds; plaster; garden paths; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.

Concrete dye pigment Hormusend HLV-21 blue is used in concrete mortar to add color.   Materials:   garden paths; paving slabs; blind areas around the house; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.

Concrete dye pigment brown Hormusend HLV-21 is used in concrete mortar to add color.   Materials:   putty; paving slabs; screeds; plaster; garden paths; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.

Concrete dye pigment yellow Hormusend HLV-21 is used in concrete mortar to add color.   Materials:   putty; paving slabs; screeds; plaster; garden paths; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.

Hormusend HLV-21 green concrete dye pigment is used in concrete mortar to add color.   Materials:   putty; paving slabs; screeds; plaster; garden paths; concrete products. Benefits:   does not dissolve in water; does not fade; Consumption: from 300 - 500 g per 25 kg of cement. A 2 kg package is sufficient for an area of 5-15 m2.