Other equipments and machines in bulk on Qoovee

Многофункциональный толщиномер защитных покрытий всех типов «Константа К6ц» измеряет толщину: гальванических (цинковых, хромовых, никелевых, кадмиевых, серебряных, оловянных и т.д) покрытий на стальных изделиях;гальванических (цинковых, хромовых, никелевых, кадмиевых, серебряных, оловянных и т.д) покрытий на изделиях из цветных металлов;лакокрасочных, эмалевых, порошовых, мастичных и др. неферромагнитных покрытий на стальных изделиях;анодноокисных, фосфатных и др. диэлектрических покрытий на изделиях из черных и цветных металлов;специальных диэлектрических и металлических покрытий большой толщины, плакирующих покрытий;покрытий на внутренних поверхностях труб и цилиндрических изделий;медной фольги на печатных платах;листовых электропроводящих неферромагнитных материалов и гальванических покрытий на изделиях из диэлектрических материалов;двухслойных покрытий;Измеряет глубину пазов и оценка шероховатости поверхности после пескоструйной или дробеструйной обработки; Контролирует климатические условия (влажности воздуха, температуры воздуха и поверхности металла, температуры точки росы и определения параметра ТΔ).

Main functions: automatic shutdown of the boiler when the pressure and temperature of the water leaving the boiler increase; manual remote shutdown of the boiler; light and sound signaling deviations of technological parameters from the norm and memorizing the root cause of the accident; remote start, stop and light indication of the operation of draft machines; control of temperature and pressure of water at the boiler outlet. The control panel of the KVr coal-fired hot water boiler has several versions: The control panel of the KVr boiler. Option 1 indicator lights and loud bang bell. Signals that the main parameters of the boiler operation are exceeded temperature and pressure; vacuum sensor in the furnace (flue); Boiler control panel KVr. Option 2 indicating devices with the display of the boiler operation parameter on the control panel display; temperature; vacuum sensor in the furnace (gas duct ); Boiler control panel KVR. Option 3 indicating devices with the display of the main parameters of the boiler operation on the control panel display; temperature and pressure; vacuum sensor in furnace (flue)

The door of the combustion boiler Bratsk is installed in boilers Bratsk, hot water boilers KVr, KVm, steam boilers, as grooves for furnace mechanical furnaces.

The smoke exhauster is a draft machine that is designed to remove flue gases - products of fuel combustion. Moving gases in the right direction is the primary task of the DN smoke exhauster. By creating the required draft in the boiler, the required performance of the boiler unit develops. Hot water and steam boilers are equipped with smoke exhausters. The smoke exhauster is designed for continuous operation with a long resource. It can be installed indoors or outdoors. The minimum temperature at which the smoke exhauster can operate is -30 ° C, the maximum one is up to 200 ° C. The smoke exhausters of right or left rotation are manufactured. If you look at the DN 3.5 / 1500 smoke exhauster from the side of the electric motor, and the rotation of the boiler smoke exhauster impeller will be counterclockwise, this will be considered counterclockwise rotation. Right-hand rotation - when the rotation of the impeller of the exhauster is performed in the clockwise direction. The main characteristics of the exhauster are performance and pressure. These parameters are controlled by an axial guide vane or a suction pocket with a gate. The suction pocket brings gases to the impeller blades more evenly and eliminates flow swirling, respectively, the efficiency of the smoke exhauster increases. The impeller is equipped with a hub to protect the bearings. The DN 3.5 / 1500 smoke exhauster can have a basic or simplified configuration, and they are also equipped with systems for efficient ash collection. The durability of the smoke exhausters is ensured by the thickened walls of the snail.

The smoke exhauster is a draft machine that is designed to remove flue gases - products of fuel combustion. Moving gases in the right direction is the primary task of the DN smoke exhauster. By creating the required draft in the boiler, the required performance of the boiler unit develops. Hot water and steam boilers are equipped with smoke exhausters. The smoke exhauster is designed for continuous operation with a long resource. It can be installed indoors or outdoors. The minimum temperature at which the smoke exhauster can operate is -30 ° C, the maximum one is up to 200 ° C. The smoke exhausters of right or left rotation are manufactured. If you look at the DN 3.5 / 1500 smoke exhauster from the side of the electric motor, and the rotation of the boiler smoke exhauster impeller will be counterclockwise, this will be considered counterclockwise rotation. Right-hand rotation - when the rotation of the impeller of the exhauster is performed in the clockwise direction. The main characteristics of the exhauster are performance and pressure. These parameters are controlled by an axial guide vane or a suction pocket with a gate. The suction pocket brings gases to the impeller blades more evenly and eliminates flow swirling, respectively, the efficiency of the smoke exhauster increases. The impeller is equipped with a hub to protect the bearings. The DN 3.5 / 1500 smoke exhauster can have a basic or simplified configuration, and they are also equipped with systems for efficient ash collection. The durability of the smoke exhausters is ensured by the thickened walls of the snail.

• Productivity of RBU: 60 cubic meters. meters per hour • Production of two grades of concrete at the same time • Twin-shaft concrete mixer V = 750 liters - 2 pieces • Fully automatic control of RBU • Production of ready-mixed concrete and reinforced concrete products (vibropress) simultaneously • The equipment is certified, the certificate of conformity GOST 27338-93 and GOST 16349-85 • Full 1 year warranty

As a rule, for many enterprises using gaseous oxygen in technological processes, its purity is of great importance. To resolve this issue, the employees of ZEPRIKON CJSC offer enterprises to use their oxygen stations with an oxygen output of 99 (± 1)%. This purity is achieved through the use of state-of-the-art oxygen production methods using pressure swing adsorption.

For filling a large number of cylinders and supplying consumers with oxygen in large volumes, a modular oxygen station was designed for filling 100 cylinders. This station is presented in three versions and can operate in the following modes: 1. refueling 100 oxygen cylinders within 8 hours; 2. refueling 100 oxygen cylinders in 18 hours; 3. Refueling 100 oxygen cylinders in 24 hours. Based on the needs of customers and their operating modes, each customer can receive his own oxygen station. In this case, the purity of oxygen can be adjusted in the range from 93 to 98%.

For remote oxygen consumers, as well as for organizations that want to organize independent production of gaseous oxygen with its injection into cylinders, it offers a solution in the form of modular oxygen stations for filling cylinders. This equipment is specially equipped with a booster compressor and a ramp for filling cylinders. As a result, at the exit you get cylinders filled with gaseous oxygen, ready for operation.

This equipment is based on the technology of short-cycle adsorption to separate air and obtain gaseous nitrogen at the outlet. This technology allows us to receive nitrogen at the outlet of our stations with a purity of up to 99.9995%. Our adsorption nitrogen stations produce nitrogen with a capacity of 20 to 8000 m3 / min and an outlet pressure of 3 to 150 bar. The stations can be made in a stationary (on a frame), modular design, on a chassis, on a sled.

For supplying remote objects, as well as large industrial enterprises with compressed air, ZEPRIKON CJSC offers the optimal solution - modular air compressor stations. This type of equipment allows you to organize an autonomous supply of compressed air to the consumer, regardless of its location. A distinctive feature of modular air compressor stations is that all technological equipment is mounted in a container, in which they function as a single system. The power source for the operation of the station is the electrical network, as well as a specially installed diesel generator. Modular air compressor stations create a maximum compressed air capacity of up to 120 m3 / min and a maximum working pressure of up to 4.0 MPa.

Mobile nitrogen station ZEPRIKON CJSC is an autonomous operating unit for the production of gaseous nitrogen. This station is based on a diesel compressor or diesel generator, which allows the station to operate without being connected to the mains. All equipment is mounted on a car chassis or installed in a metal container. Mobile nitrogen stations of ZEPRIKON CJSC allow to obtain nitrogen up to 3000 m3 / h and purity up to 99.99%. The control system of this station allows you to control all processes and equipment from one control panel and immediately set the required operating modes and characteristics of the final product.

CJSC "ZEPRIKON" designs and manufactures block-type water compressor stations of medium and high performance according to the customer's specifications. A distinctive feature of this type of station is the placement of all technological equipment in a special building - block box. The advantage of the equipment is the absence of the need to build a building for compressor equipment, the autonomy of the compressor station, high productivity, low maintenance and operation costs.

Contact Fast Freezer "KSA - 3500-12 / 1100" is designed for contact freezing of injected parts of poultry. A thin HDPE (High Density Polyethylene) film is used as a supporting element, sliding over a cooled aluminum plate in which the refrigerant circulates. This type of film is approved for contact with food. The offered equipment is fully equipped and ready to work, it is enough to connect it to the power supply and refrigerant. A complete refrigeration unit can be offered as an option. The equipment is made on a stainless steel frame with adjustable feet for precise height adjustment. All structural elements (with the exception of contact plates, which are made of aluminum), conveyor rollers, housing, etc. made of stainless steel AISI-304, and the drive rollers and shafts are coated with a polymeric coating approved for contact with food. As a drive of the film, a motor with a variable, constantly controlled rotation transmission speed is used. The spent film is wound onto a reel using a transfer coupled to the main drive. A control panel made of stainless steel is installed on the supporting frame of the equipment. The panel contains the following elements: drive motor control unit, start / stop buttons, main switch, emergency stop button and freezer plate temperature sensor.

The sorting system includes: an automated conveyor system controlled by a controller; barcode scanning system; actuators that move the product to the appropriate cells designed to work with a specific type of product. The system is designed based on the number of product types, space-planning solutions of the production site and possible additional requirements for the technological process.

Cooler for cooling bread, confectionery Lipsia is a spiral cooler with a central drum that allows you to fully automate the process of cooling bread. Benefits: • High performance; • Relatively small size; • Possibility of continuous operation for a long period of time. The bread cooler has a central or lateral drive. As a rule, products are delivered to the upper tier. To control the height of the product, a gate with an end sensor is installed at the inlet.

Equipment for bottling lemonade "Retro" is sold in configurations with three / six flasks in the form of a cone made of fiberglass or impact-resistant glass. The set includes a saturator, an assembled column for dispensing drinks, accessories for a gas bolon and a rack

The poultry cutting line is intended for cutting the carcasses of conditioned poultry (broilers, chickens, chickens) into the following parts: wings, breast, back, legs (with or without back parts), thigh, drumstick. Productivity 3000 pcs / hour. The modular design of the poultry cutting line allows you to more fully meet the needs of the customer in the production of products in demand. The line consists of the following nodes: Frame Drive station -1.5kW Tension station Wing cutting module - 2x1.5 kW Breast cutting module 2x1.5kW Backrest cutting module 1.5kW Leg and back cutting module 2x1.5kW Splitting module for hip-glen 2x1.5kW Shin release device Swivel suspension Remote Control

Hose lines - designed for the production of a multilayer bag blank with the application of an image from 2 to 6 colors with transverse and longitudinal gluing. The productivity of the lines, depending on the modification, is from 50 to 120 m / min. Control from the control panel (touch screen). Testing and control can be done remotely. The advantage of the line is the increased paper size up to 1300 mm, which allows the production of bags of any demanded format.

CNC milling machine Sale | Manufacturing | Production of any CNC machine tools A milling machine from the "ChPU24RF" Company is designed for high-quality milling and engraving of surfaces of parts and workpieces on a plane (2D) and in three-dimensional space (3D) Application area: advertising production, furniture production, interior and exterior decoration, exclusive products, door production, model production, artistic parquet production, facades Types of processed materials: Soft and hard wood, composite materials (plywood, chipboard, fiberboard, MDF, etc.), plastic, non-ferrous metal, acrylic glass

Vibropress Monolit-100, a simple, inexpensive and reliable machine for the production of small-sized concrete products by the method of semi-dry vibrocompression, it is completed with parts and units from domestic agricultural machinery, which means that after the warranty service will not become a problem for the owner either in price or in time to find the necessary details. The molding zone of the machine, in contrast to many competitors in this class, is -1000 mm, this allows the vibropress to be made the most popular vibropressed product that is in great demand on the market - road curbs and sidewalk curbs 1 meter long. Also, the vibropress can make wall blocks 39x19x19 (cm) with two or four voids, a partition wall block 39x12x19 (cm), a small sidewalk border 50x5x20 (cm) and other concrete products at the request of the customer.

Manual loading of concrete mix. The width of the forming zone is 800 mm. The vibrating press is designed for the production of wall blocks with a size of 390x190x190 mm, two-hollow or four-hollow (depending on the type of installed punch-matrix elements), partition blocks with a size of 390x100x190 mm (in the presence of the required type of punch-matrix elements). The products are molded onto technological replaceable wooden pallets. The productivity of the vibrating press is 20-30 molding cycles per hour. The number of molded products per cycle: wall block - 4 pcs., Partition block - 5 pcs. The recommended number of serviced personnel is 2 workers. Unit size without oil station and concrete mixer: length 1500 mm, width 1700 mm, height 1950 mm. Installation weight 950 kg. Scope of delivery: vibropress, oil station, hydraulic pallet pusher for transferring the pallet with molded products onto removable multi-level racks. Shaping tooling punch-matrix "two-hollow wall block 4 blocks" is included in the delivery set. Form-forming elements punch-matrix "wall block with four hollow blocks 4 blocks", and "two-hollow partition wall block 5 blocks", concrete mixer, technological pallets are supplied for an additional fee. The installed electric power of the vibrating press is 7.5 kW, voltage is 380 V. size 1500x1700x1950 mm

Concrete mixer SBM-550 (two in one) two-sheeted compulsory mixer with a horizontal shaft. Overall dimensions 2450x1500x1550 mm. Weight 1450 kg. SBM-550 (two in one) is a unique concrete mixer designed specifically for the simultaneous preparation of two mixes of concrete, different in composition and color, for the production of two-layer paving slabs by vibratory casting and, in some cases, vibro-compressed concrete products, where the multilayer molding technology is also used. Concrete mixer SBM-550 (two in one), in fact, is two different concrete mixers integrated into a common body and working from a common drive. The first (smaller) cavity of the concrete mixer is capable of preparing a ready-made solution in an amount of at least 160 liters, the second (large) at least 400. Each cavity has its own unloading hatch, and the places for unloading the finished solution at the outlet are separated by a special partition to prevent mixing of concretes of different composition.

The equipment for the production of carved candles is offered in the semi-professional and professional segment. The first is represented by small wax melters of the Hobby and MonoWax series (from 1 container for melting paraffin to 10), the second - Business wax melters (up to 12 containers).

Balanced sets of equipment and silicone molds for the production of candles (Mini-pack and hobby-pack) will allow you to make cut, other types of candles. They consist of a wax melter, silicone mold sets, wicks, dyes and varnish (depending on the model).

Advantages of the UPK-14PRGK cable rewinding device with RKU: A technological reel is supplied as standard, which allows winding cables weighing up to 300 kg and centering sleeves. The receiving stand is equipped with a hydraulic lift for lifting and lowering drums with a cable, which allows the cable to be unwound without the involvement of lifting mechanisms. The presence of wheel supports allows the operator to easily move the machine around the warehouse. The presence in the design of the Device for cable rewinding of the cable layer allows to obtain a tighter laying of the rewound material. The machine is equipped with a SEW-Eurodrive geared motor. The frequency converter allows you to smoothly change the rewinding speed from 4 to 60 rpm. Availability of the option to stop when reaching the programmed length Protection of the electric motor against voltage surges, short circuits, overheating. The device for cable rewinding UPK-14PRGK with RKU is a middle-class machine with a manual cable-laying machine, designed for winding cable and wire products with a diameter of not more than 30 mm. The device for cable rewinding UPK-14PRGK with RKU is designed to use cable reels from 8 to 14 numbers, as well as up to 14 drum numbers with the use of centering sleeves.

Cable winding device UPK-25 RFH003 - a new modified heavy-duty machine designed to replace the UPK-25RCH002. The device provides winding of cable and wire products up to 65 mm in diameter on drums with a maximum weight of up to 3 tons. The range of used cable reels is from 10 to 22 sizes. Cable rewinding machine UPK-25 RFH003 is patented. Measuring unit IDM has a patent and a certificate of type approval of measuring instruments Various modifications of the machine are produced: With RKU - manual cable layer; With AKU - automatic cable layer; C R97 - version with reinforced gearbox; S IDM - various modifications of the IDM series length meter are possible Advantages of the Device for cable rewinding on drums UPK-25RCH003: as an additional set, a technological drum can be supplied, which allows winding a cable weighing up to 300 kg the presence of a cable-laying machine in the structure of the machine allows obtaining a denser packing When equipped with AKU - an automatic cable-laying device - an even laying of the rewound material is provided without the involvement of an operator. Smooth start. The frequency converter allows you to smoothly change the rewinding speed from 0 to 30 rpm. Reversible rotation. The length meter is reversible. The presence of the option of a sound signal and automatic stop when the programmed length is reached. A line choke for voltage stabilization is provided as standard. Protection of the electric motor against voltage surges, short circuits, overheating.

The length meter IDM-20 is designed to measure long materials (cable, wire, cable, rope, etc.) with a diameter of 1 to 20 mm and can be used as an independent measuring instrument or as part of devices for rewinding cable and wire products. Installed on both manual cable rewinding machines and driven machines. The delivery set of the IDM-20 length meter includes: measuring device frame input and output roller block electronic counter of impulses (sealed) - tachometer ID-2 with a set of sensors. Advantages of the IDM-20 cable length meter: reliable welded body has a precise design, made on high-tech equipment with the use of a welding robot; counter ID-2 has established itself as an extremely reliable device, has a large digital indicator and sound; reversible counter - for basic configuration; the ID-2 meter uses original technologies to improve the measurement accuracy; sensors with overload protection. Cable length meter IDM-20 is patented and has a certificate of type approval of measuring instruments - for the basic set.

DK-5V cable jack. Screw cable jack, lifting capacity 5 tons. For cable unwinding from reels with number 8-22. This jack for cable unwinding from drums uses the screw-nut principle. The axis of the jack is threaded through the central holes of the drum, to exclude the movement of the drum along the axis during rewinding - the cable drum is fixed with clamping shoes (centering cones can be used if necessary), two racks are installed on the sides of the drum, after which the cable drum is lifted by rotating the jack handle ...

Three-scissor lifting hydraulic tables are designed to lift loads to a sufficiently large height (usually up to 12 m). Thanks to the three-scissor mechanism, it is possible to provide a significant lifting height with a relatively small lifting platform. Most often, three-scissor lifting tables are used in warehouse complexes. Also, such lifts are often used in industries where it is necessary to raise and lower large volumes of products and materials from one level to another. Three-scissor lifts are very common in car dealerships, large garages and parking lots. The weight of the lifted load can be very different: from hundreds of kilograms to ten tons. The height of the lift table when folded is dependent on the lift capacity of the lift, the size of the platform and the lift height.

EST-3 t19 machine for 3 standard blocks with dimensions 390 * 190 * 190. Simple, convenient and reliable in operation, a machine with a powerful vibration motor for 220V, Forming time for 3 blocks (1 cycle) 30-60 seconds, productivity from 50-120 blocks per hour, productivity depends on the supply of raw materials! Produced blocks with perfect geometry. The machine is suitable for the production of cinder blocks, expanded clay blocks, sand blocks, etc. The walls of the machine die are made of thick-walled metal, the hollow-formers of your choice are rectangular, round or slotted. There are also machines for 2/3/4/5/6 blocks combined options (2 blocks + 1 half-block), (4 blocks + 2 half-blocks). Concrete mixers (forced type) for 300l., 500l., 750l., 1000l., Vibrating tables, filling machines, belt conveyors, filling machines, molds for reinforced concrete rings.

EST-3 (2 + 1) t19, t-12 machine for 2 standard blocks 390 * 190 * 190 and 1 half block 390 * 120 * 190. A simple, convenient and reliable machine with a powerful 220V vibration motor, Forming time for 3 blocks (1 cycle) 35-60 seconds, productivity from 50-120 blocks per hour, productivity depends on the supply of raw materials! Produced blocks with perfect geometry. The machine is suitable for the production of cinder blocks, expanded clay blocks, sand blocks, etc. The walls of the machine die are made of thick-walled metal, the hollow-formers of your choice are rectangular, round or slotted. There are also machines for 2/3/4/5/6 blocks combined options (2 blocks + 1 half-block), (4 blocks + 2 half-blocks). Concrete mixers (forced type) for 300l., 500l., 750l., 1000l., Vibrating tables, filling machines, belt conveyors, filling machines, molds for reinforced concrete rings.

Sleigh tanks are used in harsh climatic conditions where it is difficult and almost impossible to deliver fuel or other necessary production fluid. They gained their main popularity in the northern regions, where the main part of the year is harsh climatic conditions. This type of equipment can be transported by a heavy-duty vehicle as well as any type of tractor equipment. Thus, this type of equipment is mobile. And it can be transported on any surface. A big and important factor is that it is unnecessary to prepare sites during transportation. This type of containers on sledges are distinguished by their high resistance during their operation, as well as to wear. The tanks can be equipped with various technical equipment.

Industrial heat accumulator KATRIN 1000 A with a tank volume of 1000 liters. It is a sealed reservoir that allows work under excessive internal pressure. Tank material: high-alloy carbon (boiler) or high-quality stainless steel. To increase the efficiency of the devices, external thermal insulation up to 100 mm thick is used, made in the form of a removable casing-cover. A modern heat insulator based on synthetic fibers is used, it is effective and safe. The heat accumulator is used as a storage buffer in heating and hot water systems; it does not have its own heaters and heat exchangers. Can be combined with other heat accumulators to form a battery. The main purpose is to reduce energy costs and increase the efficiency of water heaters.

Household gas meter of membrane type NPM (NPM), standard sizes G1.6; G2.5; G4 is used to account for gas consumption (liquefied, natural, cracking gas, hydrocarbon gas composition and other non-aggressive gases) in housing and communal services and everyday life. According to the gas flow, the models are right-handed (supply from right-to-left) and, accordingly, left-handed.

Mobile pressure units of the DSG trademark with various displacement capacities of 25,50,75,100,160,200,250,900 liters are intended for cleaning surfaces from rust, old paint and other deposits, as well as for surface preparation before applying anti-corrosion coatings.

For installation in workshops and closed rooms, we produce blast cleaning chambers of the KSO® trademark. The basic are injection chambers. On their basis, chambers are produced with a monoblock design, consisting of an abrasive blasting cleaning box and a built-in block of filter elements with an exhaust fan. The KSO camera turns out to be self-sufficient and does not require the connection of any additional nodes. It is convenient to operate and economical to use. Emissions of dust and other harmful substances comply with the MPE standards. Additionally, we can supply pneumatic, air-mechanical separation devices, abrasive material transportation systems - augers, elevators and conveyors of various designs in a set with a chamber.

Shot blasting lines with high performance automatically clean pipes, rolled metal products, castings, large-sized metal structures from mill scale and rust to a cleanliness class SA 3 before applying various protective coatings. This series of equipment can be divided into 5 main groups: pipe cleaning plants, rolled metal cleaning plants, casting cleaning plants, belt hearth plants, rotary table plants.

Foundry mini-plant for the production of linear fittings from non-ferrous scrap waste We produce a mini-foundry for the production of power line fittings, self-supporting insulated wire, cable and panel fittings by casting from non-ferrous scrap waste. Delivery set: reflective oven; crucible furnace; chill machine; chill molds (forms of products you need). The furnaces operate on any type of energy: low / high pressure gas, bottled gas (1 cylinder is enough for 15-20 hours of operation), electricity (30 kW / h during acceleration, no more than 15 kW in operating mode), diesel fuel, spent fuel, etc. etc. when installing the appropriate burner (to be discussed separately). Chillers can be: Single-position (open the shape to one side) for products without back corners. Two or more positional ones - opening up / down, etc. with complex forms. Power consumption 2.5 kW / h. This efficiency is achieved by the fact that the oven is turned on only when the mold is opened and closed. Kokili (casting molds) - molds are made on NB the entire series, NKK - the entire range, PA - the entire range, NZ 2-7, hardware clamps, cable fittings, etc. - the list is not limited.

Frying cabinets for catering are offered in one-, two- and three-section versions. They are used for industrial cooking. Made of stainless steel.