Agriculture Machinery & Equipment in bulk on Qoovee

The wheel type fertilizer compost turner is a patent product of our company. It is suitable for large span fermenting & pile-turning of high depth of livestock manure, sludge waste, filter mud, dregs of slag cake, straw sawdust and other organic waste. It is widely used in fermentation & decomposing and dehydrating of organic fertilizer plant, compound fertilizer plant, sludge & waste plant, garden spot and agaricus bisporus plant. Performance characteristics High composting depth: the composting depth can achieve 1.5 meters to 3 meters. Large composting span: the largest composing span can achieve 30 meters width. Lower energy consumption: it uses unique efficient energy-saving transmission mechanism. Under the same quantity of work, the energy consumption is lowerd by 70% compared with traditional compost machine. No dead corners: it uses wheel disk to compost symmetrically, under the displacement of speed governing mobile car, there is no dead corners. High degree of automation:  it is equipped with full automation electrical apparatus control system. So there is no need human operation when it is working. Working principle Using this compost turner can fully perform its mixing function. Adding some adjuvant is necessary to meet the raw material’s requirement of water content & ph value, this machine can help stir and mix them thoroughly. It can also improve the permeablity of the materials, and make the materials fluffy and elastic. At the same time, it absorbs large quantity of air and raises the temperature of fertilizer heap. If the temperature is over high, it can lower the temperature by reabsorbing fresh air, thus forming alternate state of medium-high temperature, which is beneficial to growth and reproduction of microbial flora.

This compost turner machine eliminates the hydraulic steering wheel type stacker. It is a new product owned exclusively by our company in the market. It fills the market gap that the large wheeled compost turner machines can not turn around in situ. No steering wheel required, the driver simply control two bars, then the machine can turn left or right, brake and 180 degrees turn around. Hydraulic balance of steering wheel. The height of the compost turner shaft can be automatically raised and lowered. The fertilizer pile can be forcibly turned or turned at high speed according to the moisture degree of the material. This product adopts soft start turning clutch (domestic similar products are used for iron to iron hard clutch, which will cause serious damage to chain, bearings and shaft). Equipped with front hydraulic push plate, no manual taking time to heap raw materials, drum hydraulic lifting, which greatly save the space, time, diesel, manpower and shorten the fermentation period.

Introduction of BB fertilizer production line. It is a kind of compound granule mixer for several separate fertilizers or compound fertilizers according to a certain proportion. It is characterized by granule uniformity, less water, moderate granule intensity, no agglomeration warehouse, easy to use and low cost. Line for the production of fertilizers of periodic action BB. Introduction. This BB type batch fertilizer production line is used for the efficient production of mixed fertilizers. It is designed according to different soil components in different areas and the specific requirements of compound fertilizer plants and chemical fertilizer manufacturers. Production Process of BB Series Fertilizer Production Line PLC Computer Control System –> Automatic Proportional Dosing of Raw Materials –> Lifting by Inclined Scraper –> Mixing by Roller –> Mixed Materials are Placed in Scale Storage Bins –> Quantity Packing (10-50kg)/Bag) - > Transportation and sewing -> Warehouse for granulation of finished products. Why choose our BB fertilizer production line? 1. Adopt pit dosing and accumulative weighing type, convenient for transportation and transportation of raw materials, easy to operate, saving labor. 2. Uses German Siemens PLC centralized control system, the whole production process is fully automated. 3. Large capacity, 10-30 tons per hour, more suitable for large capacity production lines. 4. Can be customized according to different requirements of customers. Bulk Material Mixing/BB Fertilizer. Scope of application of batch production line. This batch mixing packaging production line is mainly for the production of BB fertilizer, compound fertilizer, compound fertilizer by soil testing, drip irrigation fertilizer, chemical products, feed and other industries.

The process flow of the compound fertilizer production line can be divided into: raw material ingredients, raw material mixing, raw material granulation, particle drying, granular cooling, particle grading, finished packaging film and final product packaging. Characteristics of Performance The compound fertilizer production line has less investment, quick results and good economic benefits. The whole equipment process is compact, scientific and advanced. Energy saving and consumption reducing, no waste removal, stable operation, reliable running, convenient maintenance. The adaptability of raw materials is wide, and the machine is suitable for the granulation of compound fertilizer, medicine, chemical industry, feed, etc., and the granulation rate is high. This machine can produce various compound fertilizer with different concentration and different types. In particular, the granule for tombarthite and ammonium carbide compound fertilizer fills the domestic void and lead the country. Working Principle Process of compound fertilizer production line Raw material ingredients: Urea, ammonium nitrate, ammonium chloride, ammonium sulphate, ammonium phosphate (monoammonium phosphate, diammonium phosphate, and coarse whiting, ca), potassium chloride, potassium sulfate and other raw materials are matched in  proportion (according to the market demand and the around soil of test results). Raw materials mixing: The mixture of the ingredients should be mixed to improve the uniform fertilizer efficiency of the granules. Granulation of raw material: The raw material after mixing equably will be sent to granulator (drum granulator, and extruding granulator both can be used). Granulation drying: put the granulation into the dryer, and the moisture in the granules will be dried, so that the granulation strength is increased and is easier to store. Granulation cooling: After drying, the granulation’s temperature is too high and the granulation is easy to lump. While after cooling, it is easy to bagging to save and transport. Particle classification: the cooling particles that have been cooled will be graded: the unqualified particles will be crushed and regranulated, and the qualified products will be sift out. Finished film: The qualified products are coated to increase the brightness and roundness of granules. Packaging of finished product: The particles that have been wrapped the film are stored in the ventilated place.

The rapid development of livestock and poultry farming produces a lot of excrement and sewage. The harmful elements of these fouling are too high to be processed by traditional returning way. For this situation, our company has developed the organic fertilizer production line which use high efficient solid-liquid rotten aseptic deodorization technology as the core, and the whole production equipment process includes: high efficient fermentation, raw material mixing, granule processing, drying and packing. Characteristics of Performance  The products of organic fertilizer production line are made of fresh chicken and pig manure, without any chemical composition. The digestive ability chickens and pigs is poor, so they can only consume 25% of nutrients, then another 75% in feed will be excreted with faeces, so that the dry product will contain nitrogen, phosphorus, potassium, organic matter, amino acid, protein and other ingredients. In the urine and manure of livestock, a year of excrement urine of a pig, combined with the cushion material can be retted 2000 a 2500kg high quality organic fertilizer. It contains 11% of organic matter, 12% of organic matter, 0.45% of nitrogen, 0.19% of phosphorous oxide, 0.6% of potassium oxide, and is enough fertilizer for the fertilizer of whole year. These organic fertilizer is rich in nitrogen, phosphorus, potassium and other nutrients, with more than 6% content and more than 35% organic matter content, all of these is above national standard. Working Principle An organic fertilizer production line can not only meet the needs of local fertilizer, but also meet the needs of the surrounding market. Biological organic fertilizer is widely used in fields such as farmland, fruit trees, flowers, landscaping, high grade lawn, soil improvement and so on, which have a good effect. Our country subsidizes the agriculture, and it is very supportive of the industry, so investing in this industries is a good choice.

Biometric terminal for access control and time attendance systems with fingerprint and card recognition. Housing made of industrial plastic with protection against moisture and dust according to the IP53 standard. Built-in optical fingerprint scanner and Em-Marin RFID card reader. Monochrome LCD display, backlit keypad, LED and audible indication. Status toggle buttons, 8 customizable toggle event types, work code registration. Support 16 user groups and 32 time zones, real-time monitoring. Built-in relay for lock control, IR finger sensor, support for PoE standard IEEE802.3af. Interfaces: Ethernet, mini USB, RS-485, Wiegand 26/34 (input/output), exit button, door sensor, case intrusion sensor. Identification by: card, finger, ID, card + finger, ID + finger, ID + card. Number of stored fingerprints: 2000. Number of stored events: 50000. Registration of users and events in offline and network modes. Anti-passback function with optional Anviz T5s reader. Size: 80(w)*180(h)*40(d)mm. Power supply 12V (from an external power supply or via PoE), from USB (without connecting a lock). The power supply is not included in the package. Free Russified AIM CrossChex software with time tracking functions included. Options - Mifare card reader, separate executive controller (SC011), additional output reader (T5S), 1C integration module, InTime Server, SDK. Processor 32-bit ARM MCU BioNano V10 algorithm Fingerprint scanner Optical sensor (sensor) AF0S300 Scanner activation mode Automatic activation using infrared sensor Scanning area 22mm x 18mm Resolution 500 DPI (dots per inch) LCD type 128*64 dots. Number of fingerprints in device memory 2000 Number of RFID cards in device memory 2000 Number of events in device memory 50000 Recognition modes Fingerprint, login + fingerprint, login + password, password + card, fingerprint + card Recognition time less than 0.5 sec FRR (type 1 recognition error) 0.001% FAR (type 2 recognition error) 0.00001% Communication interfaces RS485, USB device, TCP/IP, Wiegand (input/output switchable) Built-in card reader Built-in reader: 125KHZ EM RFID, Optional : 13.56MHZ Mifare Fingerprint display Yes Self-selection of the event status during registration 8 Work classifier Yes Messages 50 Notifications 30 Control of DC 12V executive devices, output to external devices (COM, NO, NC) Access groups and work schedule 15 access groups, 32 temporary gap Door lock sensor Yes Acoustic emitter (siren) Yes Operating voltage DC 12V Dimensions 80(w)*180(h)*40(d)mm Tempera outdoor mode -10℃~40℃ Degree of protection IP53(Waterproof housing) Certifications FCC, CE, GOST R(GOST R) Maximum number of employees in the system Up to 1000 employees Options Mifare card reader, separate executive controller (SC011), additional exit reader (T5S), 1C integration module, SDK, InTime server

Miniature biometric terminal for access control systems with a fingerprint and card scanner. Fits on the door leaf. Dust-, moisture - resistant case, IP54. Built-in fingerprint and card reader (Em-marin), finger sensor, LED backlight and audible alarm. Identification by: finger, card, finger + card, 3000 fingerprints, 50000 events. Interfaces: Ethernet, mini USB, RS-485, Wiegand 26/34 output, exit button. Registration of users and events in offline and network modes. Size 145x55x37 mm. Power supply 12V, USB, POE. Free Russified AIM standard or CrossChex software complete with time tracking functions. Anviz P7 is an innovative new generation biometric access control system Advanced Anviz BioNano fingerprint recognition algorithm Powerful processor and shock-resistant housing Backlit touch keyboard High-contrast and durable OLED display (organic light-emitting diode display) Powered by both external source and PoE Memory for 3,000 fingerprints, 3,000 cards and 50,000 event records Built-in EM-Marine proximity card reader Built-in relay (dry contacts) to control actuators (locks, turnstiles, etc.) Wiegand In&Out, TCP/IP, RS485 and Mini USB port Remote (slave) fingerprint reader and contactless cards Anviz T5S can be connected New generation fingerprint scanner AFOS407 - durable, waterproof, dustproof and scratch resistant 50,000 event records Auto-update template fingerprint logs of registered users Intuitive Russian-language interface USB and TCP/IP data exchange for remotely adding new employees to the device memory, managing the device and integrating into other access control systems Embedded Anviz software (included free of charge) Ease of installation: easily mounted on the door frame Ideal solution for employee access control and time tracking TI Stellaris® 32-Bit High Speed ​​CPU BioNANO algorithm AFOS407 Optical Sensor Fingerprint Scanner 128mm*64mm display of fingerprints in device memory 3,000 Event log capacity 50,000 Identification method Fingerprint, Card, ID+Fingerprint, ID+Password, Password+Card, Fingerprint+Card Identification time <0.5 sec False rejection rate 0.001% False acceptance rate 0, 00001% Interfaces RS485, USB, TCP/IP, Wiegand In&Out Read module EM-Marine cards 125 kHz Relay Direct control of the lock (turnstile, barrier, etc.) Wiegand 26 output/input Connection of remote (slave) fingerprint reader and RFID cards Anviz T5S yes Anti-Passback function ) yes Auto-update fingerprint template yes Open door sensor yes PoE yes, IEEE802.3af and IEEE802.3at Power supply 12V, 800mA Touch activation yes Power saving mode yes Alarm when case is opened yes Short message reception yes Size 54mm*170mm*41mm Material Wear-resistant industrial plastic

Anviz FacePass7 is an employee time tracking system with face recognition, contactless RFID cards or password. Guarantees user identification in less than 0.5 (!) seconds. Capacity for 3,000 users Logbook 100,000 event records Two scanning cameras ensure the most accurate identification, and a high-speed processor minimizes the time to recognize employees' faces Even factors such as skin color, facial expression, gender, hairstyle do not affect the accuracy and speed of identification , as well as the presence or absence of vegetation on the face Unique infrared illumination ensures stable operation of FacaPass7 even in complete darkness Sensitive 3.2” TFT touch display Voice guidance for user actions for ease of use of the terminal Direct control of the lock (dry contacts) USB-flash for download - TCP / IP (Ethernet) data upload for data exchange and device control over the Internet Alarm when opening the case. Contactless identification. Equipped with a new architecture and artificial intelligence. The infrared detection of Face Pass 7 provides 24/7 accurate identification and effectively prevents fake faces such as photos or videos. Secure identification in various environments and conditions With over a million faces worldwide verified, FacePass 7 has become one of the most accurate face recognition terminals , suitable for various conditions Even factors such as skin color, facial expression, gender, hairstyle, as well as the presence or absence of vegetation on the face do not affect the accuracy and speed of identification. Unique infrared light, ensures FacaPass7 works even in total darkness Built-in ultra-wide-angle camera provides 120-degree identification. Brand/Manufacturer LCD Display Type Number of Device Memory Events Messages Recognition Modes FAR Error (Unregistered User Access) FRR Error (Registered User Access Denied) Maximum Number of Employees in System Communication Interfaces Scanner Activation Mode Power Supply Operating Environment Dimensions Warranty Anviz 3 ,2” TFT touch display 100,000 50 Face, password and RFID 0.1% 1% up to 3,000 people TCP/IP, USB host infrared sensor 12 V -20°...+60 °C; humidity up to 95% 54 x 170 x 41 mm 1 year

We can deliver the agricultural machinery you want.

Tedder for walk-behind tractor is aggregated with adapters PNO-1, PNO-2, PNO-3 and PNO-4 natural hayfields with a yield of more than 15 centners / ha, moisture content of the harvested mass from 25% to 80%, in small contour areas, as well as in areas with difficult access to hayfields, roadsides.

Mounted rotary mower is one of the mounted implements for walk-behind tractors and is designed for mowing grass. In the upgraded version of the KRN-1M mower, the relocated upper frame makes the familiar time-tested rotary mower even more productive. The improved version is designed for cutting thick grass that does not clog under the equipment frame.

An upgraded version of the Zarya mower: the relocated upper frame makes the familiar and time-tested rotary mower even more productive and convenient. The improved version is designed for mowing thick and tall grass that does not clog under the equipment frame as in the standard version. Our rotary type mower is unparalleled in small-scale mechanization, it is safer than front-mounted mowers, and the mowed grass is laid in a row, which does not require further raking. Diploma winner of the competition "ONE HUNDRED BEST PRODUCTS OF RUSSIA 2021". Suitable for all motor blocks with a belt drive (Neva, Oka, Cascade MB-1, MB-2, Lander, Luch, Forza, Brait). ATTENTION: for installation on Neva motoblocks of the multiagro MB1, MB2, MB23 series, mower installation kits are required.

Potato digger is designed for mechanized digging of potato tubers from the ground, laying on the surface for further manual picking. Potato digger is designed for mechanized digging of potato tubers from the ground, laying on the surface for further manual picking. The module consists of an active ploughshare (knife) and a screening grate (screen). It is aggregated with motoblocks of Chinese manufacturers with PTO. It is possible to control the depth of excavation with the help of support wheels, the softness of the separation of the soil is regulated using the engine speed of the walk-behind tractor.

A potato digger for a walk-behind tractor is an attachment and is designed for mechanized digging of potato tubers and vegetable crops, followed by screening of the earth and laying the tubers on the soil surface for further manual collection. In addition, the mechanism can be used to pick up onions, beets, garlic. The module consists of a plowshare (knife) and a sifting grate (screen). It is possible to regulate the depth of digging with the help of a hitch, the softness of the impact on the soil and tubers is regulated using the engine speed of the walk-behind tractor. The potato digger is designed to work on light and medium soils with a moisture content of not more than 27%, clogged with stones up to 8-9 t/ha, with soil hardness up to 20 kg/cm2. Compatibility with walk-behind tractors of the type: NEVA, Cascade, Favorit and walk-behind tractors of a similar design. Unit wheel track - 54 cm; and the working speed is 2 km/h.

The seeder greatly reduces the time that is usually spent on sowing seeds. Protects your health, because you do not have to bend over to crawl around the garden. In addition, the unit saves seeds, eliminates the hassle of thinning and facilitates the process of weeding in the summer. The seeder is used in coupling with motor-blocks of any types. It is also possible to use it manually with the help of two handles. One is fixed in front to the hitch of the seeder, the second is inserted into the branch pipe intended for installing the marker.

Motoblock mulcher (front connection) is designed for chopping annual and perennial plants, grass and small undergrowth in medium and large areas. The mulcher is used in conjunction with walk-behind tractors and motor-tractors. The mulcher is driven through a V-belt transmission from the motor-block engine pulley.

The trailer for attachments PNO-1 is a multifunctional convertible device designed to work with attachments of tillage equipment in household plots. On the PNO-1 lifting frame, by means of a SA-2 double hitch (not included in the set with PNO-1, but can be supplied separately at the request of the customer), you can install: a plow, a potato planter, a hiller, a potato digger, a transverse hay rake. PNO-1 is aggregated with a walk-behind tractor weighing more than 100 kg and is used outside the road network, in gardens, gardens, household plots, in all soil and climatic zones.

The small-sized potato planter KSM-1A is designed for planting seed potatoes with simultaneous embedding in the soil and forming a soil ridge, in home gardens and vegetable gardens. It is aggregated with motor-blocks of medium and heavy type: Cascade, Neva, Salyut Favorit, AGRO, MTZ and others.

Mounted rotary mower is one of the attachments to walk-behind tractors and is designed for mowing both ordinary and coarse stem and grass vegetation located in small areas and inconvenient roadsides, on slopes up to 10 degrees, etc. In the modernized KRN-1M mower, the relocated upper frame makes the familiar and time-tested rotary mower even more productive and more convenient. The improved version is designed for mowing thick and tall grass that does not clog under the equipment frame as in the standard version.

Trading House "Kharkiv Pump Plant" offers a full range of high-quality consumables and spare parts for dosing plunger pumps ND, diaphragm dosing pumps NDR-2M, three-plunger pumps PT and T. We offer spare parts: worms, housings, sliders, fingers, rings, spacers, bushings as well as all types of seals and gaskets for the hydraulic part of pumps. There is also a wide selection of pump hydraulic cylinders and major repair components. All SPTA parts are made of high quality materials at the Kharkiv Pump Plant. Whatever pump you use - diaphragm dosing NDR-2M, dosing plunger ND, three-plunger PT and T, you will find all the necessary spare parts to keep them in working condition. Knowledge, experience and reliable equipment guarantee high productivity and reduce downtime.

Innovative product, polypropylene twine, 2200tex, for hay pressing. suitable for all types of balers.

The kit includes: 1. Steering wheel adjustable back and forth 2. Frame 3. Seat base 4. Protection 5. Back and seat, adjustable back and forth 6. Fenders 7. Axle lock release levers 8. Brake cylinder 9. Brake fluid container 10. Brake caliper with platter (disc brakes) Kit weight - 91 kg

Warranty 12 months Availability status In stock Power steering no Year of manufacture 2022 Engine model R195NM Engine displacement 815³ Fuel diesel Engine power 15 hp Type of cooling water Wheel formula 4х2 (rear wheel drive) Fuel consumption 258.5 g/kW*h Fuel tank capacity 8 l. Number of grooves of the engine pulley 4 Starting method electric starter Gearbox (3+1)*2 Type of transmission belt Clutch dry, double disc, continuous contact, friction type Lifting mechanism hydraulic Brake system drum brakes on the rear wheels Transmission oil TAD-17 or TAP-15 Rear tire size 6.00-12 Front tire size 4.00-10 Cultivation depth, mm 200 Cultivation width, mm 1200 kg Cutter included

Country of Origin: Made in India. Color BLACK Trademark RABBIT. Working temperature from 0 to 70. Scope of application Power plants, underground mining, ship loading and unloading, ship-to-ship loading, mining. Tape width 600–1200 mm Tape thickness 6–20 mm. Tensile strength 10 MPa. Material Rubber. For conveyor belts with a smooth surface, the maximum inclination of the conveyor belt is approximately 20° depending on the material. The use of chevron belts allows for steeper rake angles of up to 40°, allowing more lift in less space. Chevron lined conveyor belts have rubber strips that are integrally vulcanized to the top cover of the belt. These profiles are made from high abrasion resistant rubber and are available in softer blends (45 to 50 Shore hardness) as well as 60 Shore hardness materials. The profiles are shaped so that there is no need for special rollers and they can be moved on conventional conveyors. The pitch between the two spikes ensures a smooth ride on the guide rollers.

Country of Origin: Made in India. Thickness as required. Structure Belt conveyor. I only deal with new ones. Use/Application Processing of bulk materials. RABBIT trademark.

Material Rubber/ Polyurethane/PU Brand Rabbit Country of Origin Made in India Thickness As per MI standard Structure Belt Scraper Color Black, Red, Yellow, Green Usage/Application Bulk handling

Modern CSE 180 bucket elevators from SeaSort, with a capacity of up to 180 m³/h, provide economical, fast and safe transportation of bulk material and can be used in various industries. CSE 180 bucket elevators are equipped with plastic buckets, the belt speed range is from 1.5 to 2.5 m/s, they can be used for transporting animal feed, grain or seeds. The start of the electric motor is smooth, which eliminates the possibility of breaking the buckets and cutting the keys on the upper head of the bucket elevator, and allows the use of electric motors of lower power. Convenience in repair, inspection, maintenance is inherent in the design features. Applications Transportation of bulk materials Transportation of compound feed Transportation of grain Transportation of seeds Can be installed outdoors

Modern CSE 120 bucket elevators from SeaSort, with a capacity of up to 120 m³/h, provide economical, fast and safe transportation of bulk material and can be used in various industries. CSE 120 bucket elevators are equipped with plastic buckets, the belt speed range is from 1.5 to 2.5 m/s, they can be used for transporting animal feed, grain or seeds. The start of the electric motor is smooth, which eliminates the possibility of breaking the buckets and cutting the keys on the upper head of the bucket elevator, and allows the use of electric motors of lower power. Convenience in repair, inspection, maintenance is inherent in the design features. Applications Transportation of bulk materials Transportation of compound feed Transportation of grain Transportation of seeds Can be installed outdoors

Modern bucket elevators CSE 60 from SeaSort, with a capacity of up to 60 m³/h, provide economical, fast and safe transportation of bulk material and can be used in various industries. CSE 60 bucket elevators are equipped with plastic buckets, the belt speed range is from 1.4 to 2.5 m/s, they can be used for transporting animal feed, grain or seeds. The start of the electric motor is smooth, which eliminates the possibility of breaking the buckets and cutting the keys on the upper head of the bucket elevator, and allows the use of electric motors of lower power. Convenience in repair, inspection, maintenance is inherent in the design features. Applications Transportation of bulk materials Transportation of compound feed Transportation of grain Transportation of seeds Can be installed outdoors

Modern CSE 30 bucket elevators from SeaSort, with a capacity of up to 30 m³/h, provide economical, fast and safe transportation of bulk material and can be used in various industries. CSE 30 bucket elevators are equipped with plastic buckets, the belt speed range is from 1.1 to 2.2 m/s, they can be used for transporting animal feed, grain or seeds. The start of the electric motor is smooth, which eliminates the possibility of breaking the buckets and cutting the keys on the upper head of the bucket elevator, and allows the use of electric motors of lower power. Convenience in repair, inspection, maintenance is inherent in the design features. Applications Transportation of bulk materials Transportation of compound feed Transportation of grain Transportation of seeds Can be installed outdoors

starter 0235

engine

Accessories for LED lampsLids and housings made of plastic, plastic plugs for aluminum profiles, gaskets made of gasketed thermoplastic elastomerVarious accessories for products made of soft and hard plastics.

Gaskets TEPU seals made of gasketed thermoplastic elastomer seals and moisture-proof gaskets for covers of industrial, street and office lamps. Brand: Lider Polymer LLCCountry: Russia

Autocomponent NC LLC Direct deliveries Comprehensive supply of spare parts for trucks 100% completion of applications within one day Fast quotation and provision of a commercial offer Delivery across the Russian Federation and the CIS by transport companies Reliable and proven supplier that has won the trust of its customers Competitive pricing policy Simple and convenient selection on the site A wide range for brands Kamaz Maz Ural Gas Nefaz Kraz Zil We offer cooperation Dealers Agents Online stores Purchasing departments Dropshipping

Универсальные фотосепараторы серии Horizont – это ленточные оптические сепараторы, которые применяются для сортировки пищевых и непищевых сыпучих продуктов, таких как орехи, зерновые и бобовые культуры, сушеные овощи и фрукты, кофе, замороженные продукты, чипсы и хлопья, а также для сортировки металлов, минералов и пластиков. Важной особенностью ленточных (горизонтальных) фотосепараторов Horizont является то, что продукт сортировки анализируется со всех сторон —  сверху тремя камерами над лентой транспортера, что позволяет видеть практически 100 % дефектов, и камерой на слете с него. Продукт поступает в поле зрения камер тонким, успокоенным слоем на ленте, что повышает точность анализа и удаления засорителей.  Благодаря меньшим скоростям чем на лотковых аппаратах продукт меньше травмируется — это расширяет диапазон применимости оптической сортировки. Особенности конструкции позволяют адаптировать элементы под использование с абразивными продуктами, мокрыми и сухими, в т.ч. запыленными; требующими бережного отношения. Фотосепаратор оснащен камерами высокого разрешения — 5400 пикселей работающих в видимом и инфракрасном диапазоне. Изображение полученное с камер анализируется интеллектуальной системой способной различать объекты не только по цвету, но и по сложным признакам — текстуры и формы, сортировка по 3D форме. Интеллектуальная система настройки способна сама себя подстраивать при изменении параметров входящего сырья, при минимальном вмешательстве оператора.  

Quick and easy assembly Produced on Trumpf's precision laser bending machines, structural elements are assembled approximately 30-50% faster and less skilled personnel are required for assembly. Self-supporting construction The rigid self-supporting construction of the bucket elevator due to the large number of bends and the thickness of the used sheet metal of 1.5 and 3 mm allows installing bucket elevators up to 45 meters without intermediate supports. Durable construction lasts much longer. Gentle transport The working speed of our elevators is 1.5-2.5 m/s, while that of competitors is usually 2.8-3.4 m/s, with the same performance, due to this, the transported product is less injured. Galvanized version, stainless version Galvanized version provides the best corrosion protection at minimum cost. Stainless steel version available. Transportation of material over a wide range of speeds The specially designed shape of the elevator head provides effective product discharge at a belt speed of 1.5 to 2.5 m/s, which makes it possible not to injure the material during transportation. Automation and safety Elevators can be equipped with all sensors: belt drift sensors, pressure sensor both in the head and shoe of the elevator, belt speed control sensor, reverse device. All holes for these sensors are already laid and closed. Compactness Our elevators have smaller dimensions with the same performance. This is important when there is not enough space to install a noria. Certification The produced bucket elevators have certificates of conformity, a hygiene certificate, a permit from Rostekhnadzor, and CE certificates of the European Union.

Modern bucket elevators CSE 15 by SiSort, with a capacity of up to 15 m³/h, provide economical, fast and safe transportation of bulk material, can be used in various industries. CSE 15 bucket elevators are equipped with plastic buckets, the belt speed range is from 1.1 to 2.5 m/s, they can be used for transporting animal feed, grain or seeds. The start of the electric motor is smooth, which eliminates the possibility of breaking the buckets and cutting the keys on the upper head of the bucket elevator, and allows the use of electric motors of lower power. Convenience in repair, inspection, maintenance is inherent in the design features. The quality of workmanship and thoughtfulness of the design of elevators. Fast installation. In our elevators, more buckets per 1 m of belt are installed, due to this, the wear of buckets is less by 20-40%. The exit in the head has a slope of 35 degrees. This saves installation height. In the basic configuration, all models of bucket elevators have a lining of the head. All elevators are equipped with two suction pipes in the base.

Goggles (partially insulating) - modern, lightweight, universal, made of polycarbonate with a panoramic protective glass. Designed to protect the eyes from the front, top and sides from mechanical impacts, abrasive, UV radiation, direct splashes, splashes of biological fluids . Protective glass is resistant to chemicals, acid and alkali solutions, disinfectants. Features: • Enhanced panoramic view • Light weight • Double-sided anti-fog, abrasion and scratch resistant coating • 100% UV protection • Increased frontal, side and top protection, can be worn with corrective glasses • Compatible with many types of PPE WHEN WHOLESALE ORDER - VOLUME DISCOUNT!!!

The 400-liter copper jug is used to mix spirits, including gin or whiskey. It can be burned with steam, gas, electricity or wood. Easy-to-use CIP cleaning system and automatic stop control. The perfect starting scale for a new spirits business. Technical parameter Pear-shaped helmet with thermometer and inspection glass Copper pot-Ø 900 mm; 3-4 mm strong, Filling capacity 400 liters Approximately 500 liters of full capacity Inlet Ø 400 mm Side-mounted dedicated distillation tower Outlet Ø 200 mm with ball valve 4″ Newly constructed plate to improve the quality of aroma The water bath is completely made of stainless steel and insulated Special-shaped helmet: stainless steel flange connection, no visible screws or washers inside and outside, with sight glass and thermometer. Indirect heating: a steam bath covered with stainless steel and insulated. Copper super aromatics (special distillation tower) 450 mm Ø with 3 bubble caps Blister: a new structure that increases the turbulent movement of the copper surface and the liquid The liquid level of the distillation pan can be adjusted freely-the alcohol content and aroma of the distilled mash can be flexibly adjusted. Include a pre-condenser (fractionator) in the column head Inspection mirror: 4 125mm Ø observation windows for each blister and saccharification reflux Stainless steel condenser: V4A material, diameter 220mm, height 1500mm, automatic cooling with thermostatic regulating valve Safety features: overflow, vacuum circuit breaker, pressure gauge, automatic exhaust, steam trap and dirt filter. Alcohol tube, distilled water, water outlet device of water outlet: completely made of stainless steel. Heating method: steam or electricity Contact us The special attention we give in the final quality inspection of each work is also a guarantee of unparalleled reliability and robustness. If you have any needs or questions, please contact us.